DATA BOOK - BVT Partners OÜ

(2) Remote Installation controller (RC-E5) manual for wired remote controller'11 • SCM-DB-109PJA012D730terminal block.Connect the terminal of remRead together with indoor unit's installation manual.with the terminal of indoor uWARNING(X and Y are no polarity)Wiring route is as shown inFasten the wiring to the terminal securely and hold the cable securely so as not to apply unexpected stress on thedepending on the pulling outerminal.Loose connection or hold will cause abnormal heat generation or fire.Make sure the power supply is turned off when electric wiring work.The wiring inside the remoteOtherwise, electric shock, malfunction and improper running may occur.The sheath should be peeleCAUTIONPulling out from upper leftDO NOT install the remote controller at the following places in order to avoid malfunction.X wiring : 215mm(1) Places exposed to direct sunlight(4) Hot surface or cold surface enough to generate condensationY wiring : 195mm(2) Places near heat devices(5) Places exposed to oil mist or steam directly(3) High humidity places(6) Uneven surfaceInstall the upper case as bethe screws.DO NOT leave the remote controller without the upper case.In case of exposing cord, fixIn case the upper cace needs to be detached, protect the remote controller with a packaging box or bag inInstallation and wiring of remoorder to keep it away from water and dust.Wiring of remote controller sMaximum prolongation of reAccessories Remote controller, wood screw (ø3.516) 2 piecesIf the prolongation is over 10Prepare on site Remote controller cord (2 cores) the insulation thickness in 1mm or more.But, wiring in the remote con[In case of embedding cord] Erectrical box, M4 screw (2 pieces)of the case according to wire[In case of exposing cord] Cord clamp (if needed)connecting section. Be care100 - 200m.........................0Installation procedureUnder 300m.......................0Open the cover of remote controller , and remove the screw under theUnder 400m.......................1buttons without fail.Under 500m.......................2Remove the upper case of remote controller.ScrewMaster/ slave setting when moInsert a flat-blade screwdriver into the dented part of the upper partA maximum of two remote controof the remote controller, and wrench slightly.[In case of embedding cord]Indoor unitsEmbed the erectrical box and remote controller cord beforehand.Controller cordRemote cErectrical box(Prepare on site)Remote controller Remote contSW1 "Master"SW1 "SlavPrepare two M4 screws (recommended length is 12-16mm) on site, and install the lower case to erectrical box.Choose either of the following two positions in fixing it with screws.Upper partUpper partSet SW1 to "Slave" for the slaNote: The setting "Remote controTighten the screws aftercutting off the thin part ofcontroller in the position whLower caseLower casescrew mounting part.The air conditioner operatiomaster/ slave setting of it.Wiring ouletLower partLower partThe indication when power souWiring ouletWhen power source is turned on,communication between the remConnect the remote controller cord to the terminal block.Master remote controller : "Connect the terminal of remote controller (X,Y) with the terminal ofM4 screw 2 (Prepare on site)Slave remote controller : "indoor unit (X,Y). (X and Y are no polarity)The thin partUpperAt the same time, a mark or a nuInstall the upper case as before so as not to catch up the remote controller cord,This is the software's administratand tighten with the screws.Lower case[In case of exposing cord]LowerYou can pull out the remote controller cord from left upper part or center upper part. UpperWhen remote controller cannot cCut off the upper thin part of remote controller lower case with a nipper or knife,appear.and grind burrs with a file etc.Lower caseCheck wiring of the indoor unit anInstall the lower case to the flat wall with attached two wooden screws.Lower