DATA BOOK - BVT Partners OÜ

BEFORE INSTALLATION Before installation check that the power supply matches the air conditioner.- 105 - '11 • SCM-DB-10912345678910111213Standard accessories (Installation kit)Accessories for indoor unitInstallation board(Attached to the rear of the indoor unit)Wireless remote controlRemote control holderTapping screws(for installation board 4dia. by 25mm)Wood screw(for remote control switch holder 3.5(mm). by 16mm)Battery [R03(AAA,Micro) 1.5V]Air-cleaning filtersFilter holders(Attached to the front panel of indoor unit)Insulation (#486 50 x 100 t3)Sealing plateSleeveInclination platePuttyOption partsDrain hose (extention hose)Piping cover(for insulation of connection piping)Necessary tools for the installation workPlus headed driverKnifeSawTape measureHammerSpanner wrenchTorque wrenchHole core drill (65mm in diameter)Wrench key (Hexagon) [4m/m]Flaring tool setGas leak detectorGauge for projection adjustmentUsed when flare is made by using( conventional flare tool )Pipe bender(14.0 ~ 61.0N·m(1.4 ~ 6.1kgf·m)Designed( )for R410AspecificallyDesigned specifically( )for R410A)Q'ty111422221Q'ty111111SELECTION OF INSTALLATION LOCATION(Install at location that meets the following conditions, after getting approval from the customer)Indoor unit Where there is no obstructions to the air flow and where the cooled and heated air can be evenly distributed. A solid place where the unit or the wall will not vibrate. A place where there will be enough space for servicing. (Where space mentioned below can be secured) Where wiring and the piping work will be easy to conduct. The place where receiving part is not exposed to the direct rays of the sun or the strong rays of the street lighting. A place where it can be easily drained. A place separated at least 1m away from the television or the radio. (To prevent interference to images and sounds.) Places where this unit is not affected by the high frequency equipment or electric equipment. Avoid installing this unit in place where there is much oil mist. Places where there is no electric equipment or household under the installing unit.Wireless remote control A place where the air conditioner can be received the signal surely during operating the wireless remote control. Places where there is no affected by the TV and radio etc. Do not place where exposed to direct sunlight or near heat devices such as a stove.CAUTIONINSTALLATION OF INDOOR UNITInstallation of Installation boardLook for the inside wall structures (Intersediats support or pillar and finallyinstall the unit after level surface has been checked.)Level position (2 locations)Mating mark forlevel surfaceDrilling of holes and fixture of sleeve (Option parts) Drill a hole with whole core drill.Installing the support of pipingIn case of piping in the right rear direction Hold the bottom of the Tape only the portionpiping and fix direction that goes through thebefore stretching it and wall.shaping it. Always tape the wiringwith the piping.Sufficient care must be taken not to damagethe panel when connecting pipes.450Fixing on concrete wallUse of nut anchorUse of bolt anchorBolt(M6 12)Mountingboard In case of rear piping draw out, cut off the lowerand the right side portions of the sleeve collar.Standard holePiping in the left rear directionPiping in the left direction5 cm minimumfrom the wallWhen drilling the wall that contains a metal lath, wire lath or metal plate, be sure to use pipe hole sleeve sold separately.Indoor side65Shaping of pipingsPipingsDrain hoseOutdoor side5Nut(M6)MountingboardMax.10Taping of the exteriorb Topb cThicknese of the wall + 1.5cm• Matters of special notice when piping from left or central/rear of tha unit.[Top view]Left-hand-side piping[Drain hose changing procedures]Completely seal the hole onthe wall with putty. Otherwise,furniture, or other, may bewetted by leaked water ordewing.aTurn totightenIndoor sideIndoor side Outdoor side Installed statePiping in the right rear directionWireless remote controlRemote control holderWood screwsPiping in the right direction7.0 cm minimum from the ceilingSleeve(sold separately)INSTALLATION SPACE (INDOOR UNIT)49222.55012048Space forservice220Installation board10 cm minimumfrom the wallRelation between setting plate and indoor unitRight-hand-side piping1. Remove the drain hose. 2. Remove the drain cap. 3. Insert the drain cap. 4. Connect the drain hose.(FRONT VIEW)Indoor unitInstallation boardSpace forservice 100650120450 22035 3558 54Piping hole (ø65) Remove the screw and Remove it with hand or Insert the drain cap which was removed Insert the drain hose securely,drain hose, making itrotate.pilers.at procedure “2” securely using ahexagonal wrench etc.Note: Be careful that If it is not Insertedsecurely, water leakage mayoccur.making rotate. And install thescrew.Note: Be careful that If it is notInserted securely, waterleakage may occur.puttyAdjustment of the installation board in the horizontaldirection is to be conducted with four screws in a temporarytightened state.Adjust so the board will be level by turning the board withthe standard hole as the center.Nothing is connected to thishole on the back of indoorunit.Outdoor sideputtyPiping for Liquid (20 to 60 type) : ø6.35Piping for Gas (20 to 35 type) : ø9.52(50 to 60 type) : ø12.7Drain hose (ø16) 520.8Piping for Gas 491.1Piping for Liquid 559.1Piping hole (ø65)70 Space for service487.7295.715 Space for service5.6Piping is possible in the rear, left,left rear, left downward, right ordownward direction.RightRearDownward Left rear LeftLeft downward