Leica TDRA6000 Product Brochure - GeoWILD

More documents

Recommendations

Info

Targets and AccessoriesWith a collection of different metrology grade reflectors, adaptersand accessories, the Laser Station Leica TDRA6000 can beequipped to measure almost anything.Tripods and StandsWhether you work indoors or out, the stability of your setup isparamount. Therefore Leica Geosystems has a selection of tripodsto make sure that your specific job needs can be fulfilled.
Leica TDRA6000 Laser Station AccuraciesAll measurements are performed under stable indoor environmentalconditions with the target squarely aligned. Distance measurementsare verified against a laser interferometer over 120 m. Unless statedotherwise, all accuracies are Maximum Permissible Error (≈ ±3 σ),with typical accuracies being ½ MPE (or approximately ±1.5 σ).3D Point AccuracyThe measurement uncertainty of a coordinate “U xyz” is defined as thedeviation between a measured coordinate and the nominal coordinateof that point. This measurement uncertainty is specified as a functionof the distance between the Laser Station and the measured point.The accuracy specified below is achieved with Leica Geosystems1.5” Red Ring reflectors and the “Precise” measurement mode. Specificationsare stated in Maximum Permissible Error (MPE). Typical resultsare ½ MPE.U xyz≤ 30 m volumeU xyz> 30 m volume± 0.5 mm ± 0.3 mm + 13 µm/m3D Point ReproducibilityThe 3D Point Reproducibility “P re” is defined as the standard deviationbetween multiple measurements of a 3D point and is specified as afunction of the distance between the LaserStation and the measuredpoint. The accuracy specified below is achieved with Leica Geosystems0.5” TBR and/or RFI reflectors using the “Precise” measurement mode.P re≤ 30 m volume ± 0.2 mmEDM PerformanceEDM Performance 1.5” 0.5” Reflective NonRRR & BRR 2 TBR & RFI 2 Tape 3 Contact (RL) 4Max Volume 600 m 600 m 600 m 600 mMin Distance 2.0 m 2.0 m 5.0 m 2.0 mAccuracy (MPE) 1 0.5 mm 0.5 mm 1.0 mm 2.0 mm1Accuracy shown is Maximum Permissible Error (MPE). Typical results are 1/2 MPE.2The 1.5” RRR is measured on the laser rail as standard.320 mm x 20 mm target from 5 m to 60 m.4RL measurements are done against the laser rail from 2 to 60 mPower Search PerformancePower Search PerformanceMax VolumeMin DistancePositioning time 11 200 gon to full ATR Lock1.5” RRR & BRR100 m2.0 m< 5 secondsATR PerformanceATR 1.5” 0.5” ReflectivePerformance RRR & BRR TBR & RFI 2 TapeMax Volume 600 m 400 m 40 mMin Distance 2.0 m 2.0 m 5.0 mAccuracy (MPE) 1 ± 0.3 mm + 13 µm/m N/A ± 2.0 mm1Accuracy shown is Maximum Permissible Error (MPE). Typical results are 1/2 MPE.2TBR & RFI reflectors can be used for point reproducibility (i.e. deformation studies).General InformationTelescope MagnificationFocusing range30 x1.7 m to infinityKeyboard and Display Display: ¼ VGA, color, touch, both facesKeyboard: 34 keys, illuminatedData storage Internal memory: 256 MBMemory card: CompactFlash card 256 MB or 1 GBInterfacesOperationRS232, Bluetooth ® WirelessThree endless drives for one ortwo hand operation Precisiontrigger key for manualmeasurementsPower Management Internal: lithium-ion batteryExternal: AC power supplyWeight Laser Station incl. battery7.6 kgEnvironmental specificationsOperating temperatureDust/waterHumidity–20° C to +50° C(IEC 60529) IP5495%, non-condensing
Page 1 and 2: Leica TDRA6000Product BrochureVersi
Page 3 and 4: A new level of speed andperformance
Page 5: Railway ManufacturingThe process of

Leica TDRA6000 Product Brochure - GeoWILD

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?