Planck Pre-Launch Status Papers - APC - Université Paris Diderot ...
Planck Pre-Launch Status Papers - APC - Université Paris Diderot ... Planck Pre-Launch Status Papers - APC - Université Paris Diderot ...
J. A. Tauber et al.: Planck pre-launch status: The optical systemTable 4. Planck reflector characteristics at ambient temperature and 40 K.Reflector Design parameter Ambient temperature a Estimated in-flight parameter Estimated uncertaintyPR R = 1440.0 mm R = 1440.41 mm R = 1439.266 mm ±0.1mmk = −0.869417 k = −0.86782 k = −0.867266 ±0.001rms (ring 1,µm) = 7.5 3.5 5.0 brms (ring 2, µm) = 12 4.2 8.2rms (ring 3, µm) = 20 5.3 8.8rms (ring 4, µm) = 33 6.0 8.6rms (ring 5, µm) = 50 16.0 12.6rms (whole surface, µm) = 7.0 8.6SR R = 643.972 mm R = 644.043 mm R = 643.898 mm ±0.1mmk = −0.215424 k = −0.21541 k = −0.215094 ±0.001rms (ring 1, µm) = 7.5 3.6 4.7 crms (ring 2, µm) = 12 3.9 4.5rms (ring 3, µm) = 20 6.2 7.0rms (ring 4, µm) = 33 5.3 5.7rms (ring 5, µm) = 50 11.5 13.2rms (whole surface, µm) = 6.1 10.6Core-wall print-through (±µm) = d 0.4PTV (dimpling, µm) = e
A&A 520, A2 (2010)materials. Therefore, the values of R and K extrapolated to40 K are affected by significant uncertainty, being in practiceconstrained only to a range between linear extrapolation andthe value measured at 90 K.2. Medium-scale features are predicted by the FEMs, whichare also found in the measured surfaces, namely local deformationsaround the isostatic mounts (ISMs), a large central“shelf” of diameter defined by the location of the ISMs, a depressedring outside the circle of the ISMs, and a “curlingup”of the edge areas. However, the predicted amplitude ofthese features is smaller by an order of magnitude than whatis measured.3. On small scales, the behaviour is dominated by the dimpling,i.e. the behaviour of the facesheet within each core cell as afunction of distance from the centre. The measured surfaceis much more inhomogeneous than predicted by the FEMs,i.e. most cells do not exhibit simple concave dimples butmultiple-peak features with amplitudes that are much higherthan the FEM predicts 5 .TheFEMsalsopredictthatthedimplingdepends on the distance from the centre of the reflector,driven by the large-scale reflector curvature. None of theFEM-predicted small-scale behaviour is clearly reproducedin the measurements.Overall, the FEMs have been rather unsuccessful in predictingdetailed reflector thermoelastic behaviour, probably becauseof the dominance of very-small-scale variations in the materialproperties at the interface between the core-cells and thefacesheets. As a consequence, the predictionofthereflectorshapes and associated uncertainties atoperationaltemperatureshas been purely empirical. As described in Sect. 5.1, the reflectorfigures were extrapolated from the evolution measured betweenambient temperature and 95 K. The uncertainty of the beam prediction(Sect. 7) was assumed to lie between the parameter valuesat 95 K and the worst-case extrapolation.Fig. 8. The rms WFE of the full set of horns for the three flight predictionscenarios (nominal or as-built, best and worst cases, defined inSect. 7.1). The top panel shows the absolute WFE (in wavelengths),and the lower panel the WFE of the best and worst cases normalisedby that of the nominal case. The frequency increases from right to left.The horn ID is labelled by instrument (HFI or LFI), frequency and increasinghorn number (as in Fig. 4). The three cases were defined at353 GHz (centre of the focal plane); at other frequencies, compensationsmean that the “worst-case” WFE is not always larger than the“best-case” WFE. Nonetheless, the spread represents the uncertainty inthe in-flight WFE at all frequencies. The best case is clearly very closeto the nominal one in terms of the WFE, but the worst case is quite far,especially at the higher frequencies.5.3. In-flight alignmentThe SR and focal plane were shimmed at ambient temperaturesuch that when the telescope cools, the system will come intooptimal alignment as determined by CodeV. The optimizationtook into account the predicted deformation of the mirrors andstructure. The WFE for the nominal, best, and worst case deformationsis shown in Fig. 8.The uncertainty in the in-flight alignment has the strongestinfluence on the uncertainty in the predicted beam shapes. Theelements contributing the most to the alignment uncertainty are:(a) the rotation of the focal plane assembly; (b) displacement ofthe SR along the X direction (see Fig. 5).AMonteCarloanalysiswasperformedofthefullalignmentbudget, taking into account all the expected thermo-elasticdeformations in the system. Code V was used to compute at353 GHz the WFE of a horn near the centre of the focal plane,for 3000 cases drawn from the estimated error distributions ofeach misalignment type, including displacements, rotations, anddeformations of the reflector figures. The set of 3000 cases coversthe range of misalignment cases that may be encountered inflight. For each case, the optimal location of the telescope focalplane (i.e. the location that minimizes WFE) was computed usingsensitivity coefficients for each individual misalignment, andcompared to the design locationofthefeedhornphasecentre;5 This is fortunate because it significantly reduces the ordered dimplesthat would produce unwanted grating lobes.the difference constitutes the true misalignment of that case inan optical sense. The results of this analysis (see Fig. 9)indicatethat the misalignment uncertainty is of order ±0.7 mm(1σ) inthe defocus direction, which has averysignificantimpactontheability to predict the optical performance in-flight (see Sect. 6.2).Early in the development, concerns were raised that thealignment process relied on a complex accumulation of measurementsand extrapolations, which were not verified by an end-toendmeasurement at operating frequencies. It was noted that if ahuman error were made in this process (and not caught by “standard”verification practices), it would not be found until flight(the “Hubble” problem). An end-to-end measurement of theflight hardware is infeasible because of the need to operate thePlanck detectors at low temperatures, which cannot be achievedin an RF measurement chamber. Therefore, an additional (coherent)320 GHz detector/feedhorn assembly was placed in the focalplane, whose purpose was to verify that no such human errorhad been made. A special technique based on modulated reflectivitymeasurements was developed (and validated on the qualificationmodel of the Planck telescope) that allowed us to measurethe radiation pattern of this detector in a compact antennatest range (CATR) with a dynamic range of ∼15 dB (Paquayet al. 2008). The shape of the pattern varies rather sensitivelywith deviations from the optimal location, in particular defocus.This measurement therefore allowed us to determine the locationof the focal plane, at ambient conditions, with an accuracyof ±1 mm(Paquayetal.2008), which was considered adequatePage 10 of 22
- Page 1 and 2: A&A 520, E1 (2010)DOI: 10.1051/0004
- Page 3 and 4: ABSTRACTThe European Space Agency
- Page 5 and 6: A&A 520, A1 (2010)Fig. 2. An artist
- Page 7 and 8: A&A 520, A1 (2010)Fig. 4. Planck fo
- Page 9 and 10: A&A 520, A1 (2010)Fig. 6. The Planc
- Page 11 and 12: A&A 520, A1 (2010)Table 4. Summary
- Page 13 and 14: A&A 520, A1 (2010)three frequency c
- Page 15 and 16: A&A 520, A1 (2010)Fig. 12. The left
- Page 17 and 18: A&A 520, A1 (2010)Fig. 14. Left pan
- Page 19 and 20: A&A 520, A1 (2010)flux limit of the
- Page 21 and 22: A&A 520, A1 (2010)- University of C
- Page 23 and 24: A&A 520, A1 (2010)57 Instituto de A
- Page 25 and 26: A&A 520, A2 (2010)Fig. 1. (Left) Th
- Page 27 and 28: A&A 520, A2 (2010)Fig. 3. (Top)Twos
- Page 29 and 30: A&A 520, A2 (2010)Table 2. Predicte
- Page 31: Table 3. Predicted in-flight main b
- Page 35 and 36: A&A 520, A2 (2010)Fig. 11. Comparis
- Page 37 and 38: A&A 520, A2 (2010)Table 5. Inputs u
- Page 39 and 40: A&A 520, A2 (2010)Fig. 16. Three cu
- Page 41 and 42: A&A 520, A2 (2010)Table 7. Optical
- Page 43 and 44: A&A 520, A2 (2010)Fig. A.1. Dimensi
- Page 45 and 46: A&A 520, A2 (2010)5 Università deg
- Page 47 and 48: A&A 520, A3 (2010)Horizon 2000 medi
- Page 49 and 50: A&A 520, A3 (2010)Fig. 1. CMB tempe
- Page 51 and 52: A&A 520, A3 (2010)Ω ch 2τn s0.130
- Page 53 and 54: A&A 520, A3 (2010)Fig. 6. Integral
- Page 55 and 56: A&A 520, A3 (2010)Table 2. LFI opti
- Page 57 and 58: 3.3.1. SpecificationsThe main requi
- Page 59 and 60: A&A 520, A3 (2010)Fig. 11. Schemati
- Page 61 and 62: A&A 520, A3 (2010)features of the r
- Page 63 and 64: A&A 520, A3 (2010)Fig. 13. Level 2
- Page 65 and 66: A&A 520, A3 (2010)Fig. 15. Level 3
- Page 67 and 68: A&A 520, A3 (2010)GUI = graphical u
- Page 69 and 70: A&A 520, A3 (2010)23 Centre of Math
- Page 71 and 72: A&A 520, A4 (2010)In addition, all
- Page 73 and 74: A&A 520, A4 (2010)Table 2. Sensitiv
- Page 75 and 76: A&A 520, A4 (2010)Fig. 2. Schematic
- Page 77 and 78: A&A 520, A4 (2010)Fig. 6. LFI recei
- Page 79 and 80: A&A 520, A4 (2010)Fig. 9. Schematic
- Page 81 and 82: A&A 520, A4 (2010)Table 4. Specific
J. A. Tauber et al.: <strong>Planck</strong> pre-launch status: The optical systemTable 4. <strong>Planck</strong> reflector characteristics at ambient temperature and 40 K.Reflector Design parameter Ambient temperature a Estimated in-flight parameter Estimated uncertaintyPR R = 1440.0 mm R = 1440.41 mm R = 1439.266 mm ±0.1mmk = −0.869417 k = −0.86782 k = −0.867266 ±0.001rms (ring 1,µm) = 7.5 3.5 5.0 brms (ring 2, µm) = 12 4.2 8.2rms (ring 3, µm) = 20 5.3 8.8rms (ring 4, µm) = 33 6.0 8.6rms (ring 5, µm) = 50 16.0 12.6rms (whole surface, µm) = 7.0 8.6SR R = 643.972 mm R = 644.043 mm R = 643.898 mm ±0.1mmk = −0.215424 k = −0.21541 k = −0.215094 ±0.001rms (ring 1, µm) = 7.5 3.6 4.7 crms (ring 2, µm) = 12 3.9 4.5rms (ring 3, µm) = 20 6.2 7.0rms (ring 4, µm) = 33 5.3 5.7rms (ring 5, µm) = 50 11.5 13.2rms (whole surface, µm) = 6.1 10.6Core-wall print-through (±µm) = d 0.4PTV (dimpling, µm) = e