AT-15 HD 16 Owners Manual - American Tactical Imports

More documents

Recommendations

Info

PROBLEMS / SOLUTIONS…PROBLEM CHECK FOR: WHAT TO DO:BOLT FAILS TO LOCKAFTER LAST ROUNDDIRTY OR CORRODEDBOLT LATCHFAULTY MAGAZINECLEAN - OR REPLACE - BOLT CATCHCHECK FOR BUFFER ENDCAP BACKOUTOR OBSTRUCTIONCHECK FOR FULL TRAVEL OF BOLT CARRIERREPLACESELECTOR LEVERBINDSNEEDS OILDIRT OR SAND UNDERTRIGGERLUBRICATE WITH CLPCLEANBOLT CARRIER“HUNG UP”ROUND JAMMEDBETWEEN BOLT ANDCHARGING HANDLEAND/OR DOUBLE FEEDWARNING:KEEP CLEAR OF MUZZLECAUTION:AFTER ROUND IS REMOVED,BOLT IS UNDER TENSION1.) REMOVE MAGAZINE.2.) PUSH IN ON THE BOTTOM OF THE BOLTLATCH.3.) WHILE PULLING DOWN ON CHARGINGHANDLE, TAP THE RIFLE BUTT ON THE GROUND.BOLT SHOULD LOCK TO THE REAR.4.) WHILE BOLT IS HELD TO THE REAR, ROUNDSHOULD FALL THROUGH THE MAGAZINE WELL.NOTE: IF THIS PROCEDURE FAILS, USE ASECTION OF CLEANING ROD TO PUSH THE BOLTFULLY TO REAR THROUGH THE EJECTION PORT.PAGE 34Manufactured by Head Down Products
COLD WEATHER SHOOTING…If cold weather requires it, your rifle can be shot with gloved or mittened hands. The TriggerGuard is designed to allow the use of a glove. If needed open and swing down allowing betteraccess to Trigger when the shooter is wearing gloves or mittens. Some Head Down lower receivershave integrated trigger guards that can not be removed.1.) Push in Forward TriggerGuard Pin with Bullet tipto release Trigger Guard.2.) Swing Trigger Guarddown for shootingwith gloves or mittens.CAUTION!… Be careful of accidental discharges when inserting glovedfingers into Trigger Guard area.MAINTENANCE IN EXTREME WEATHER…EXTREME COLD: Clean and lubricate Rifle in a warm room with Rifle at room temperature. Do notlay a warm Rifle directly on snow or ice. Moving Rifle from cold into warmth will causecondensation which could keep Rifle from functioning.HOT, WET CLIMATES: Clean and lube Rifle more frequently in moist climates. Inspect hiddensurfaces of Bolt and Carrier Assembly, Upper Receiver, and Chamber / Barrel Extension(Locking Lugs), and Lower Receiver and Receiver Extension Assembly (Buffer Tube) for rustor corrosion. Also pay close attention to the Spring Loaded Detents on the rifle. Wipeoff any hand / finger prints on the Rifle as they can accelerate the onset of rust or corrosion.HOT, DRY CLIMATES: Take extra care with cleaning and lubrication as rifle will be exposed toblowing sand and fine dust, and extreme temperature shifts (hot in the daytime, freezing atnight). Corrosion is less likely to form on metal parts in a dry climate. Lightly lube functionalparts only - too much lubrication can attract and hold dust and sand.RAINS: DO NOT FIRE THE RIFLE IF WATER IS PRESENT IN THE BARREL. Excess pressure cancause the Rifle to explode.ALWAYS drain any water from Barrel prior to firing. Dry the Bore with a Swab and CleaningRod if wet.PAGE 35Manufactured by Head Down Products
Page 1 and 2: TMAmerican TacticalHD-16Manufacture
Page 3 and 4: PLEASE PRACTICE SAFE FIREARMS HANDL
Page 5 and 6: ABOUT YOUR HEAD DOWN RIFLE...This O
Page 7 and 8: PREVENTATIVE MAINTENANCE CHECKS & S
Page 9 and 10: OPERATION OF YOUR RIFLE… LOADINGC
Page 11 and 12: OPERATION OF YOUR RIFLE… (CONTINU
Page 13 and 14: IMMEDIATE ACTIONS — IN CASE OF TR
Page 15 and 16: BULLET STUCK IN THE BORE…WARNING:
Page 17 and 18: DISASSEMBLING YOUR RIFLE… (Contin
Page 19 and 20: DISASSEMBLING YOUR RIFLE… (Contin
Page 21 and 22: INSPECTION — CLEANING — LUBRICA
Page 23 and 24: CLEANING THE UPPER RECEIVER…NOTE:
Page 25 and 26: CLEANING THE LOWER RECEIVER…1.) C
Page 27 and 28: LUBRICATION - BOLT CARRIER GROUP…
Page 29 and 30: REASSEMBLING YOUR RIFLE… (Continu
Page 31 and 32: REASSEMBLING YOUR RIFLE… (Continu
Page 33 and 34: PROBLEMS / SOLUTIONS…PROBLEM CHEC
Page 35: PROBLEMS / SOLUTIONS…PROBLEM CHEC
Page 39 and 40: LIMITED MANUFACTURERS WARRANTYHead

AT-15 HD 16 Owners Manual - American Tactical Imports

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?