Series 9820Q ASTRA Installation/Operation Manual - Gasboy

More documents

Recommendations

Info

GASBOY Series 9820QSW1-6 AuthorizationThis switch allows activation of the 9820Q from sometypes of fuel management systems. When the switchis closed, a 115 VAC (230 VAC Int’l) signal must bepresent on the Control Feed line for pump activationto occur (required setting for Series 1000, TopKATmechanical, and all non-GASBOY systems ). Whenopen, the 9800 ignores the Control Feed line(required setting for CFN, TopKAT electronic, or nofuel system).AuthorizationYesNoSW1-6 Fuel SystemClosed Series 1000TopKAT mechanicalAll Non-GASBOY systemsOpen CFNTopKAT top-mountTopKAT electronicNo fuel systemSW1-7 TotalizersThis switch should be set to open for normal operation. When closed, thisswitch enables the reset of the electronic totalizers. See View/ResetTotalizers later in this section for details.SW1-8Not used.TotalizersResetNormalSW1-7ClosedOpenSW2This four-position switch pack serves a dual purpose: as an address setting when communicating on the GASBOYRS-485 loop or TopKAT, or as a pulser output rate selector when pulser data is sent to a fuel management systemother than a GASBOY CFN or TopKAT.Address SwitchesA unique address identifier must be set when the 9820Qis connected to the GASBOY RS-485 pump loop via the9820Q RS-485 I/F PCB. Because there are 16 possibleaddress combinations, up to 16 units (single or twin) maybe connected to the pump loop. Addressing should startat 1 and continue sequentially through 16. The physicalwiring order does not have to correspond with the addressorder; that is the first unit on the RS-485 loop doesn'thave to be address 1. The chart at right gives the switchsettings and address selections.Address SW2-11 Closed2 Open3 Closed4 Open5 Closed6 Open7 Closed8 Open9 Closed10 Open11 Closed12 Open13 Closed14 Open15 Closed16 OpenSW2-2ClosedSW2-3ClosedSW2-4ClosedClosed Closed ClosedOpen Closed ClosedOpen Closed ClosedClosed Open ClosedClosed Open ClosedOpen Open ClosedOpen Open ClosedClosed Closed OpenClosed Closed OpenOpen Closed OpenOpen Closed OpenClosedClosedOpenOpenOpenOpenOpen Open OpenOpen Open Open30 MDE-4339 9820Q ASTRA Installation/Operation • July 2004
Pump OperationPulser Output Rate SwitchesWhen the 9820Q is connected to external control equipmentother than a GASBOY CFN system (standalone), the pulsersignals are sent out via the 9820Q Pump I/F PCB. The pulserate required by the monitoring equipment can be configured bysetting the switches as shown in the chart at right. The pulse raterepresents pulses per gallon (PPG, domestic) or pulses per liter(PPL, international). For domestic units, the pulse rate can be upto 1000 PPG. For international units, the pulse rate can be up to250 PPL for all other models. This switch may need to be sealedby a Weights and Measures paper seal if the 9820Q is used forthe resale of product.Leading zeros are always suppressed in the hundreds and tenspositions to the left of the decimal point. When in standalonemode, positions to the right of the decimal point are displayedbased on the pulse rate selected as shown in the table at right.Timeout SwitchWhen the 9820Q is in standalone mode, it will turn off an activehose if it doesn't detect pulses for 4 minutes, 15 seconds. Thistimeout feature can be disabled by setting switch SW2-4 toOPEN.Pulse Rate SW2-1 SW2-2 SW2-31 Closed Closed Closed10 Open Closed Closed100250ClosedOpenOpenOpenClosedClosed5001000ClosedOpenClosedClosedOpenOpenNoneNoneClosedOpenOpenOpenOpenOpenPulse Rate Display1:1 XXX.10:1 XXX.X100:1250:1XXX.XXXXX.XXX500:11000:1XXX.XXXXXX.XXXTimeoutEnabledDisabledSW2-4ClosedOpenMDE-4339 9820Q ASTRA Installation/Operation • July 2004 31
Page 1 and 2: Series 9820Q ASTRAInstallation/Oper
Page 4 and 5: FCC InformationThe US Federal Commu
Page 6 and 7: GASBOY Series 9820Q023866 Wiring Di
Page 8 and 9: GASBOY Series 9820QOptional Feature
Page 12 and 13: GASBOY Series 9820QTypical Installa
Page 14 and 15: GASBOY Series 9820Q011930 Base Layo
Page 16 and 17: GASBOY Series 9820Q011885 Base Layo
Page 18 and 19: GASBOY Series 9820Q12 MDE-4339 9820
Page 20 and 21: GASBOY Series 9820QNeutral FeedThe
Page 24 and 25: GASBOY Series 9820QGroundTo ensure
Page 26 and 27: GASBOY Series 9820QConduitAll wirin
Page 34 and 35: GASBOY Series 9820QElectronic Compo
Page 38 and 39: GASBOY Series 9820QATC Information
Page 40 and 41: GASBOY Series 9820QTo view the pump
Page 42 and 43: Start-up and Test6. Start-Up and Te
Page 44 and 45: GASBOY Series 9820Q1. Check meter r
Page 46 and 47: GASBOY Series 9820QClean the Dial F

Series 9820Q ASTRA Installation/Operation Manual - Gasboy

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?