CEMB C72 Parts List
CEMB C72 Parts List CEMB C72 Parts List
1.4 - SPECIFICATIONSingle phase power supply................................ 115 - 230 V 50-60 HzProtection class ................................................ IP 54Max. power consumption................................... 1100 WBalancing speed approx. ................................... 180 min -1Cycle time for average wheel (14 Kg).............. (14 Kg) 6 secondsBalancing accuracy ........................................... 0,1 grammiPosition resolution ............................................. ± 1.4 °Average noise level............................................ < 70 dB(A)Distance rim - machine...................................... 0 - 280 mm (400 mm can be preset)Larghezza cerchione impostabile ..................... 1.5” ÷ 20” or 40 ÷ 510 mmDiameter setting range ...................................... 10” ÷ 24” or 265 ÷ 615 mmTotal wheel diameter within guard ..................... 1067 (42”)Total wheel width within guard........................... 500 (42”)Max. wheel weight ............................................. 65 Kg.Min/max. compressed air pressure.................... 7 ÷ 10 Kg/cm 2 approx. 0.7 to 1 Mpa; approx. 7 to 10 BAR;.........................................................................................approx. 100 to 145 PSI.2 - HANDLING AND HOISTINGFig. 2Fig. 2aNB: DO NOT HOIST THE MACHINE USING DIFFERENT GRIPSI 0226 GB - 4
3 - COMMISSIONING3.1 - ANCHORINGThe machine can be operated on any fl at non-resilient fl oor.Make sure that the machine rests solely on the three support points provided (fi g. 2a).It is advisable to secure the system to the ground using the specific feet (see Figure 2a) in theevent of continual use with wheels weighing over 35 Kg.3.2 - ELECTRICAL CONNECTIONThe machine is supplied with a single phase mains cable plus earth (ground).The supply voltage (and mains frequency) is given on the machine nameplate. It may NOT be changed.Connection to the mains should always be made by expert personnel.The machine should not be started up without proper earth (ground) connection.Connection to the mains should be through a slow acting safety switch rated at 4A (230V) or 10A (115V) .3.3 - PNEUMATIC CONNECTION (Versions SE)For operation of the spindle with pneumatic locking (costant thrust air spring) connect the balancing to thecompressed air main. The connection fi tting is located at the back of the machine. At least 7 Kg/cm 2 (~ 0.7MPa; ~ 7 BAR; ~ 100 PSI) pressure is needed for correct operation of the release device.3.4 - EXTRA SAFETY DEVICES (VERSION SE)- Wheel always locked even when there is pressure failure during the balancing cycle.- Always actuate the unlocking control pedal with the machine stationary in order to avoid stressand abnormal wear on the adapter.3.5 - ADAPTER MOUNTINGThe balancing machine is supplied complete with cone adapter for fastening wheels with central bore.Other optional fl anges can be mounted once the terminal part is removed (also see enclosed brochures)N.B. Carefully clean the coupling surfaces before performing any operationa) DISMOUNTING THREADED END PIECEFig. 3ABa) Back-off screw B and remove threaded end-piece A.b) Fit the new adapterI 0226 GB - 5
- Page 1 and 2: Instructions for useIContentsPage1
- Page 3: 1- GENERAL1.1 - GENERAL SAFETY RECO
- Page 7 and 8: SE2-Dismounting360°abcdConee- Qua-
- Page 9 and 10: 4.3 - AUTOMATIC DISTANCE AND DIAMET
- Page 11 and 12: OPERATION FUNCTIONS MENUEccentricit
- Page 13 and 14: 5.2.1.1 - “AUTOMATIC WIDTH” OPT
- Page 15 and 16: 5.3 - RECALCULATION OF THE UNBALANC
- Page 17 and 18: RESULTS UNBALANCE MEASUREMENTFig. 1
- Page 19 and 20: 5.4.4 - ALU AND STATIC MODESFrom th
- Page 21 and 22: 6.1 - SELF-DIAGNOSTICS6 - SET UPDIS
- Page 23 and 24: 6.3 SCREEN SAVERIt is possible to e
- Page 25 and 26: 6.3.3 - WIDTH GAUGE (OPTIONAL)Set w
- Page 27 and 28: 10 - RECOMMENDED SPARE PARTS LIST(F
- Page 29 and 30: 111923 10456737811108111Guarnizione
- Page 31 and 32: C 72 (A) - C 72SE (B)E-0226-C72-GB.
- Page 33 and 34: D0112-111 2 3 4 5 6 7 68 9 6 7 10 1
- Page 35 and 36: D0140-1.1-BP1.1-BPONLY BN. CODE DAT
- Page 37 and 38: D0112-33123 4121110945687N. CODE DA
- Page 39 and 40: D0186-44171511716152431413111256879
- Page 41 and 42: D0186-6611B25 2624231211A105 6 7222
- Page 43: D0186-8-428-42N. CODE DATA N. CODE
- Page 46 and 47: M 0226 - 2 GB
- Page 48 and 49: 3.2 - CALIBRATION OF THE DISTANCE P
- Page 50 and 51: 5 - TROUBLE SHOOTING SEQUENCETests
- Page 52 and 53: 6 - POWER SUPPLY LAYOUT DIAGRAMFig.
1.4 - SPECIFICATIONSingle phase power supply................................ 115 - 230 V 50-60 HzProtection class ................................................ IP 54Max. power consumption................................... 1100 WBalancing speed approx. ................................... 180 min -1Cycle time for average wheel (14 Kg).............. (14 Kg) 6 secondsBalancing accuracy ........................................... 0,1 grammiPosition resolution ............................................. ± 1.4 °Average noise level............................................ < 70 dB(A)Distance rim - machine...................................... 0 - 280 mm (400 mm can be preset)Larghezza cerchione impostabile ..................... 1.5” ÷ 20” or 40 ÷ 510 mmDiameter setting range ...................................... 10” ÷ 24” or 265 ÷ 615 mmTotal wheel diameter within guard ..................... 1067 (42”)Total wheel width within guard........................... 500 (42”)Max. wheel weight ............................................. 65 Kg.Min/max. compressed air pressure.................... 7 ÷ 10 Kg/cm 2 approx. 0.7 to 1 Mpa; approx. 7 to 10 BAR;.........................................................................................approx. 100 to 145 PSI.2 - HANDLING AND HOISTINGFig. 2Fig. 2aNB: DO NOT HOIST THE MACHINE USING DIFFERENT GRIPSI 0226 GB - 4