CEMB C72 Parts List
CEMB C72 Parts List CEMB C72 Parts List
5 - INDICATIONS AND USE OF THE WHEEL BALANCER5.1 - DOUBLE OPERATOR PROGRAMThis program allows memorizing the dimensions of two types of wheels. Thus two operators can worksimultaneously on two different cars using the same balancing machine. The system memorizes twoprograms with various preset dimensions.1 - Press to select operator (1 or 2). Selection is confi rmed by panel-mounted LED.2 - Enter the dimensions (see PRESETTING OF WHEEL DIMENSIONS)3 - carry out the balancing as usualWith program 1 or 2 is called for subsequent balancing operations without having to newly enterthe dimensions.5.2 - PRESETTING OF WHEEL DIMENSIONS5.2.1 - AUTOMATIC PRESETTING- Standard wheels (calibration necessary also for modes ALU 1, 2, 3, 4 Static)Fig. 8 DISTANCE + DIAMETERMove the gauge tip into contact against the rim keeping it inposition for at least 2 seconds.N.B. Measurement is the same in position A or B. Always usethe round part of the contact tip.Pos. APos. BIndication of gauge in movementIndication of dimensions acquired.N.B.: When the beep signal is enabled (see section CONTROLOF THE FUNCTIONS MENU), reaching of the dimensions isaccompanied by a “beep”Return the gauge to position 0. If automatic WIDTH readout isdisenabled (see GAUGE ENABLE), the system automatically goes to theWIDTH position.The system automatically switches to WIDTH position- The nominal width is normally stampedon the rim; if not, proceed to measuredimension “b” with the calibre gauge(supplied as standard).I 0226 GB - 12
5.2.1.1 - “AUTOMATIC WIDTH” OPTIONIf WIDTH measurement with sonar is enabled, the machine is set for the acquisition of this value:Fig. 9The LT script on the LH matrix display indicates that LIGHT TRUCK wheel measurement is set (largedimension wheels such as off-road, trucks or wheels which protrude signifi cantly from the rim).This function can be enabled/disenabled by pressing push button prior to the measurement, whichis then performed by closing the guard; once completely closed and if “automatic START on guard closure”is enabled, the launch will be made for unbalance measurement. If automatic START is disenabled, oncethe guard is closed the display will show the width value measured.5.2.1.2 - WHEEL ALU-S(correction from inside for two balancing planes with direct calibration):Fig. 10After measurement for inside F1 as shown, again remove the gauge in order to memorize the data for theoutside FE; keep the position for at least 2 seconds. The measurement can be made either in the positionshown in Fig. 8/Pos.A or in Fig. 8/Pos.B.Manual presetting is possible by using the push buttons as for detailed hereunder.I 0226 GB - 13
- Page 1 and 2: Instructions for useIContentsPage1
- Page 3 and 4: 1- GENERAL1.1 - GENERAL SAFETY RECO
- Page 5 and 6: 3 - COMMISSIONING3.1 - ANCHORINGThe
- Page 7 and 8: SE2-Dismounting360°abcdConee- Qua-
- Page 9 and 10: 4.3 - AUTOMATIC DISTANCE AND DIAMET
- Page 11: OPERATION FUNCTIONS MENUEccentricit
- Page 15 and 16: 5.3 - RECALCULATION OF THE UNBALANC
- Page 17 and 18: RESULTS UNBALANCE MEASUREMENTFig. 1
- Page 19 and 20: 5.4.4 - ALU AND STATIC MODESFrom th
- Page 21 and 22: 6.1 - SELF-DIAGNOSTICS6 - SET UPDIS
- Page 23 and 24: 6.3 SCREEN SAVERIt is possible to e
- Page 25 and 26: 6.3.3 - WIDTH GAUGE (OPTIONAL)Set w
- Page 27 and 28: 10 - RECOMMENDED SPARE PARTS LIST(F
- Page 29 and 30: 111923 10456737811108111Guarnizione
- Page 31 and 32: C 72 (A) - C 72SE (B)E-0226-C72-GB.
- Page 33 and 34: D0112-111 2 3 4 5 6 7 68 9 6 7 10 1
- Page 35 and 36: D0140-1.1-BP1.1-BPONLY BN. CODE DAT
- Page 37 and 38: D0112-33123 4121110945687N. CODE DA
- Page 39 and 40: D0186-44171511716152431413111256879
- Page 41 and 42: D0186-6611B25 2624231211A105 6 7222
- Page 43: D0186-8-428-42N. CODE DATA N. CODE
- Page 46 and 47: M 0226 - 2 GB
- Page 48 and 49: 3.2 - CALIBRATION OF THE DISTANCE P
- Page 50 and 51: 5 - TROUBLE SHOOTING SEQUENCETests
- Page 52 and 53: 6 - POWER SUPPLY LAYOUT DIAGRAMFig.
- Page 54 and 55: 8 - TO CHECK MACHINE CALIBRATION1)
- Page 56: M 0226 - 12 GB
5 - INDICATIONS AND USE OF THE WHEEL BALANCER5.1 - DOUBLE OPERATOR PROGRAMThis program allows memorizing the dimensions of two types of wheels. Thus two operators can worksimultaneously on two different cars using the same balancing machine. The system memorizes twoprograms with various preset dimensions.1 - Press to select operator (1 or 2). Selection is confi rmed by panel-mounted LED.2 - Enter the dimensions (see PRESETTING OF WHEEL DIMENSIONS)3 - carry out the balancing as usualWith program 1 or 2 is called for subsequent balancing operations without having to newly enterthe dimensions.5.2 - PRESETTING OF WHEEL DIMENSIONS5.2.1 - AUTOMATIC PRESETTING- Standard wheels (calibration necessary also for modes ALU 1, 2, 3, 4 Static)Fig. 8 DISTANCE + DIAMETERMove the gauge tip into contact against the rim keeping it inposition for at least 2 seconds.N.B. Measurement is the same in position A or B. Always usethe round part of the contact tip.Pos. APos. BIndication of gauge in movementIndication of dimensions acquired.N.B.: When the beep signal is enabled (see section CONTROLOF THE FUNCTIONS MENU), reaching of the dimensions isaccompanied by a “beep”Return the gauge to position 0. If automatic WIDTH readout isdisenabled (see GAUGE ENABLE), the system automatically goes to theWIDTH position.The system automatically switches to WIDTH position- The nominal width is normally stampedon the rim; if not, proceed to measuredimension “b” with the calibre gauge(supplied as standard).I 0226 GB - 12