Instruction Guide Golvo Classic - www.liko.com

GolvoInstruction GuideEnglish7EN140106-012010-06-04Applies to the following models:Golvo 8000 Classic art. nr 2000024Golvo 8008 Classic art. nr 2000025Golvo 8000 ClassicGolvo 8008 ClassicProduct DescriptionGolvo is a versatile mobile lift, intended for use inmost lifting situations, for example, between bed andwheelchair, to/from toilet, bath and shower, to/fromthe floor, for weighing purposes and for lifting witha stretcher.The wireless hand control gives the caregiver thefreedom to work closer to the patient, which providesextra security in the lifting situation. For the caregiver thisalso enables an ergonomically enhanced work posture.Golvo is equipped with the Liko Diagnostic System,a monitoring system which continually registers operatingdata and automatically indicates when the lift is in needof service.The battery of the lift has built-in charge indicator wherethe charging status of the battery can be read, evenwhen the battery is not attached to the lift. The batteryis of environmentally friendly NiMH type.Individual fitting of the sling and other lifting accessoriesis of utmost importance for function and safety whenusing the lift.is a warning triangle used for situations which require extra care and attention.In this document, the person being lifted is referred to as the patient, and the person helping is referred toas the caregiver.IMPORTANT!Read the instruction guides for both the patient lift and lifting accessories before use. Lifting and transferringa person always involves a certain level of risk. It is important to completely understand the contentsof the instruction guides. The equipment should only be used by trained personnel. Please contactyour Liko representative in the event of any uncertainties or questions.

Table of ContentsSafety Instructions..........................................................................................2Definitions.......................................................................................................3Technical Data................................................................................................3Dimensions.....................................................................................................4Assembly........................................................................................................5Disassembly....................................................................................................7Operation........................................................................................................8HandControl IR.............................................................................................10Operation Panel............................................................................................ 11Charging the Batteries.................................................................................. 11Maximum Load.............................................................................................12Recommended Lifting Accessories...............................................................12Simple Troubleshooting............................................................................... 15Inspection and Maintenance ........................................................................16NOTE! This instruction guide contains important information for users of the product. All those who use theproduct should review and fully understand the contents of the instruction guide. Remember to keep the instructionguide in a place where it is always available to those using the product.Safety InstructionsBefore using the first time make sure that:• the lift is assembled in accordance with the assembly instructions• the lifting accessory is properly attached to the lift• the batteries have been charged for at least 5 hours• you have read the instruction guides for the lift and lifting accessories• personnel using the lift are informed of the correct operation and use of the lift.Before lifting, always make sure that:• the lifting accessories is selected appropriately in terms of type, size, material and designwith regard to the patient’s needs• the lifting accessories are not damaged• the lifting accessory is correctly attached to the lift• the lift strap is not twisted or worn and can move in and out of the lift• the lifting accessory hangs vertically and can move freely• the lifting accessory is correctly and safely applied to the patient in order to prevent injuries• the safety latches are intact; missing or damaged safety latches must always be replaced• the sling’s strap loops are correctly connected to the sling bar hooks when the sling strapis extended, but before the patient is lifted from the underlying surface.Never leave a patient unattended during a lifting situation!Golvo have been tested by an accredited testing institute and fulfil the requirements specified in the Medical DeviceDirective for class 1 products (MDD 93/42/EEC).Golvo complies with the requirements in EN ISO 10535, IEC 60601-1, IEC 60601-1-2, ANSI/AAMI ES60601-1 andCAN/CSA C22.2 no. 60601-1Under no circumstances must the lift be modified. If you have any questions, please contact Liko.Particular care must be observed when using strong sources of potential disturbance, such as diathermy, etc,so that diathermy cables are not positioned on or near the lift. If you have questions, please consult the responsibleassistive-device technician or the supplier.The lift must not be used in areas where flammable mixtures may occur, for example in areas where flammablegoods are stored.Golvo Classic • 7EN140106-01w w w . l i k o . com

DefinitionsGolvo 8000/8008 Classic1. Lift Strap171615141312111093456712Forward direction82. Sling bar with safety latches3. HandControl IR4. Parking panel for sling bar5. Holder for Quick Reference Guide and colour codefor sling sizes6. Product decal7. Lift mast with inbuilt motor8. Front wheels9. Base10. Rear wheels with brakes11. Motor for base-width adjustment12. Control box with emergency stop built-in chargerand operation panel (electrical emergencylowering/raising)13. Control box IR receiver14. Battery15. Handles16. Emergency Lowering (mechanical)17. Lift armTechnical DataMaximum load:Material:Weight:Wheels:Turning diameter:Emergencylowering device:Lifting speedwith no load:Lifting interval:Sound level:Protection class:Operating forces,controls:HandControl IR:200 kgAnodised aluminiumGolvo 8000 Classic: 39 kg (86 Ibs)Golvo 8008 Classic: 41 kg (90 Ibs)Heaviest removable part:Golvo 8000 Classic: 18 kg (40 Ibs)Golvo 8008 Classic: 19 kg (42 Ibs)Front: 75 mm* (3 inch.) twin wheels.Rear: 75 mm (3 inch.) twin wheels withbrakesGolvo 8000 Classic: 1240 mm (49 inch.)Golvo 8008 Classic: 1330 mm (52 inch.)Mechanical and electricalTwo speeds; 41 mm/s (1.61 inch/s)and 33 mm/s (1.3 inch/s)1260 mm (50 inch.) (height-adjustable)52,8 dB(A)IP X4Buttons on hand control: 4 NButton on display: 4 NBatteries: 2 AAA LR03 1.5 V, alkaline.Reach: 2 m (78.74 inch.)Electrical data:Intermittentoperation:Battery:Battery charger:Lift motor:Motor for basewidthadjustment:Protected by Patent24 VInt. Op 10/90, active operation max 2 min.Only 10% of a given length of time maybe active, yet no more than 2 min.NiMH cells, 2.2 Ah. New batteriesprovided by the supplier.CBL20001, built-in, 100-240 V AC,50-60 Hz, max 600 mA.24 V, 6.5 A24 V, 3.5 AThe device is intended for use indoors.Type B, in accordance with the electrical shockprotection class.Class II equipment.Golvo Classic • 7EN140106-01w w w . l i k o . com

DimensionsLateral viewTop viewM700 mm 700 mm(27.5 Inch.) (27.5 in)DCAD2OLmaxEEGLminF1F600 mm 600 mm(23.6 Inch.) (23.6 in)B3B2B1BMaximumreachTable of measurementsModelGolvo8000Golvo8008ACDB B1 B2 B3* B4max. min. max. min. max. min.(mm)D2* E F F1 G L max L min M O1995 1360 1115 800 435 435 - 938 654 826 543 0 975 105 25 840 1735 475 440 3622090 1455 1185 870 480 480 - 1020 735 907 623 0 1100 105 25 940 1860 600 436 391ModelGolvo8000Golvo8008(Inch.)ACDB B1 B2 B3* B4max. min. max. min. max. min.D2* E F F1 G L max L min M O78.5 53.5 43.9 31.5 17.1 17.1 - 36.9 25.7 32.5 21.4 0 38.4 4.1 1.0 33.0 68.3 18.7 17.3 12.882.3 57.3 46.6 34.2 18.9 18.9 - 40.2 28.9 35.7 623 0 43.3 4.1 1.0 37 73.2 23.6 17.2 15.4The lifting interval 1260 mm (50 inch.) is height-adjustable, see page 9. Lifting height dimensions are based on the lift being equipped witha standard sling bar and standard wheels. When changing to other lifting accessories, check that the lift still achieves the desired lifting height.* Reference measurement according to Standard EN ISO 10535:2006.Golvo Classic • 7EN140106-01w w w . l i k o . com

AssemblyBefore assembly, make sure you have the following parts and tools:• lift mast with control box, handle with 4 st M8 screws,sling bar with safety latches, 2 M6 screws, bolt andlock nut (M8)• base with width adjustment motor• battery• HandControl IR• bag containing: instruction guide, quick referenceguide, handle reinforcement for emergencylowering, charger cable, charger connector cable,cable lid with screws (2), back cover with alternativesuspension clip for the hand control, 2 adhesivebuttons for hanging up the hand control on anda cord for HandControl IR.• tools: 13 mm spanner, 4, 5 and 6 mm Allen keys.Lock the wheels on the base before starting to assemble the lift.AB1. Unscrew and remove the transportation guard (metal plate)at the bottom of the lift mast. Remove the transportationguard, its attachment screws and the red information decal.A) Position the lift mast between the two black plasticplugs on the base cross member.B) Then push the lift mast forwards as in the figure aboveso that it hooks onto the cross member.2. Screw the two provided M6 screws intothe upper holes on the lift mast.No screws in the lower holes!3. Assemble the handle using the 4 provided M8screws to the appropriate holes on the lift mast.4. Assemble the sling bar (or other lifting accessory)with the provided bolt and lock nut (M8). Checkthat the bolt is properly tightened.Golvo Classic • 7EN140106-01w w w . l i k o . com

12 35. Connect the cables as follows:- Charger cable to socket 1- Cable from lift motor to socket 2- Cable from motor for base-widthadjustment to socket 3.6. Thread the cables through the opening in thecable lid. Push the lid up and secure with theprovided Allen key and screws (2).7. Place the battery in itsbracket in the control box.Check to see that the batteryis secured in its position.8. Hang the hand control on thegreen “button” on the mast. Twoextra self-adhesive “buttons” forpositioning the hand control areprovided.9. Press the handle reinforcementinto place with the text “Emergencylowering” visible on the emergencylowering handle.10. Place the Quick ReferenceGuide in the holder on thelift mast.11. Release the emergency stopby turning the button in thedirection indicated by the arrowson the button.12. Before initial use, charge thebattery by plugging the chargercable into the connector cable.Then plug the charger cable intoan electrical socket (100-240 V AC).The battery charges fully in about5 hours.Golvo Classic • 7EN140106-01w w w . l i k o . com

13. Place the charger cable on the intended hookon the lift mast after completed charging.14. Activate the IR system by pressing any buttonon the operation panel.After assembly, make sure that:• the motion of the lift arm corresponds to thebuttons on the hand control/operating panel;• the emergency lowering functions are working(mechanical and electrical);• the wheel brakes are working;• the base-width adjustment works;• the batteries are charged.Disassembly1. Begin by removing the sling bar or other accessory that is fitted to the lift.2. Remove the cables from the control box, see page 6.3. Remove the handle, see below:4. Remove the lift mast as described below:When the lift mast has been detached from the base, it must be supported to prevent it from falling.A. Unscrew both the safety screws in the upper holeson the lift mast.Golvo Classic • 7EN140106-01B. Then screw the safety screws into the lower holeson the lift mast. This releases the lift mast from thebase, and it can now be removed.w w w . l i k o . com

OperationActivate:Reset:Emergency stopActivate: Press the red button on the control box.Reset: Turn the button in the direction indicatedby the arrows.Electrical emergency lowering/raisingThe lift arm is lowered/raised electrically bypressing one of the markings for “down” and “up”,respectively, on the operation panel.AReplacing the Hand Control BatteriesWhen the indicator A on the hand control flashes (yellow),the batteries in the hand control should be replaced. Use2 batteries of type AAA LR03 1.5 V, alkaline.Remove the back cover using a cross-head screwdriver.Replace the batteries. Refit the back cover.Installation of safety latchesAfter installation, check that the safety latch locksand runs freely in the sling bar hook.LockUnlockLocking the WheelsThe rear wheels can be locked to prevent rotating andturning. To lock the wheels, push down the lock pedal withyour foot. To disengage, press the raised button at the wheel.When lifting, the wheels should be unlocked so that the liftcan be moved to the patient’s centre of gravity. The wheelsshould be locked however, if there is a risk of the lift rollinginto the patient, for instance, when lifting from the floor.Mechanical emergency loweringEmergency lower by moving the handle marked”Emergency lowing” up and down. Repeat themotion until the patient in the lift is lowered ontoa firm surface; draw down the sling bar manuallyand continue to pump the handle until the slingbar is low enough to enable the sling’s strap loopsto be unhooked.Locked wheels during lifting can increasethe risk of tipping.Golvo Classic • 7EN140106-01w w w . l i k o . com

aAfter mechanical emergency lowering / Restoringthe lifting levelIf the lift strap has been lengthened due to using theemergency lowing function, the lift interval height willbe lower than previously. To restore maximum liftingheight, the lift strap must be reset to its original length.Do as follows:1. Unload the strap above the emergency loweringdevice. Do this by either placing the sling bar abovethe lift arm or by another person holding the sling barup so that the strap hangs loose.2. Lower and raise the handle marked ”Emergencylowering” with your left hand. At the same timetension the strap by turning the black knob (a)clockwise with your right hand. Repeat thisprocedure until the red mark on the strap is justabove the emergency lowering device.Adjustment of the lift interval levelIf it is necessary to reach a lower level with the slingbar, this can be arranged by lengthening the lift strapusing the mechanical emergency lowering device.Do not lengthen the strap more than necessary asthe highest obtainable lifting level is also affected.An example it would be advantageous to lower thelift interval is when lifting from the floor using a slingwhose strap loops do not reach up to the sling barhooks when the lift is in its lowest position.Do as follows: Push down the red emergencylowering handle at the same time as loading the slingbar (pull down the sling bar with your other hand).This extends the strap and the sling bar is lowered.Repeat until the required strap length is obtained.WRONG!WRONG!Avoid unbalanced liftingAlways ensure that the lift strap is vertical and parallelto the lift mast when lifting. To achieve this, think ofGolvo’s position under the bed. Adjust the width and/orplace Golvo differently under the bed to achieve thecorrect position.Do not lift when the load is unbalanced on the lift strapas this can cause instability as well as wear the strap.Unbalanced lifting poses a tipping risk!Parking the sling barWhen the lift is not in use or is being moved withouta load, it can be beneficial to place the sling barin the parking panel.The parking panel is intended for parking UniversalSlingBars 350, 450 and 600 (all models).When the sling bar is parked in the parkingpanel, the lift should not be raised since thiscould be dangerous and cause personnel injuryor damage to the lift if the sling bar should releaseand swing out from the panel.Golvo Classic • 7EN140106-01w w w . l i k o . com

HandControl IRThe hand control has 6 buttons:UpDownUp (lower speed)Down (lower speed)Base wideningBase narrowingIf the lift has not been used for more than 24 hours, the system must be enabled by pressing any buttonon the control box operation panel before the HandControl IR can be used.A HandControl IR can be used to control several Liko patient lifts (overhead lifts and mobile lifts that are equipped withthe same IR system). If further hand controls are to be used with the lift, IR control must be activated as describedbelow in A.Important! If more than one IR-controlled lift is present in the same room, each lift has to be given a uniquecommunication code in order to avoid maneuvering several lifts with one hand control. A unique communicationcode is created as per operation B.A.A. Enable IR control: Hold the HandControl IR approx.20 cm (8 inch.) from the control box’s IR receiver andpress the hand control’s large Up and Down buttonssimultaneously approx. 2 s. When a signal is emitted,the function is enabled. The lift is now ready to be usedwith the HandControl IR.B.B. Check if the other lifts in the room are affected by yourhand control.If other lifts are affected by your hand control: Use thelarge Up and Down buttons on the operation panel ofthe lift to be used. Press the two buttons simultaneouslyuntil a signal is emitted. The lift now has a uniquecommunication code.Now enable the IR control, see A above.Hand control enabled (green light)- Illuminates when the control box is receiving signals from the hand control.Overload (orange light)Operation PanelThe lift can be operated directly from the operation panel on top of the control box. On the operation panel thereare a number of indicator lights with corresponding symbols; see the description below.Illuminates if the lift’s recommended max. load is exceeded, and the lift stops. The indicator turns offafter 3 s. and the lift operates again. Read more about maximum load on page 12.Service indication (orange light)- IIlluminates when service is needed. Contact the service technician authorized by Liko.ELT, Expected Life Time (red light)- When the light flashes during lifting, the Liko Diagnostic System indicates that the expected life timefor the lift is approaching its end.Contact the service technician authorized by Liko.If the ELT proceeds to shine continuously when lifting, the lift should be taken out of service.Contact the service technician authorized by Liko.Golvo Classic • 7EN140106-0110 w w w . l i k o . com

Charging the Batteries2341Battery CapacityCheck the battery capacity by pressing the i button (1).The following information is available:2 - Green light: More than 50 % of the battery capacity remains.3 - Orange light: 25–50 % of the battery capacity remains.4 - Orange light: 0–25 % of the battery capacity remains.The indication lamps light up for about half a minute; they then go out.The battery capacity is also shown when the lift is in use.To obtain max. service life, it is important to charge the batteries regularly. We recommend charging afteruse of the lift or every night. Maximum charge is obtained after about 5 hours. When the batteries are fullycharged, the charger switches to trickle charging automatically.During charging the lights shine alternatively (orange, orange, green). Completed charging is indicated bya flashing green light. When the operation time is noticeably shortened, the batteries probably need changing.Stop charging and switch batteries.Never charge batteries in a wet area.The lift cannot be charged with the emergency stop engaged.NOTE! If the lift is not to be used for a long period, the battery should be connected to charging.ChargingWith built-in charger:Check that the charger cable is connected to the control box outlet; see p. 6.Connect the charger cable to an electrical outlet (100-240 V AC).Completed charging is indicated by a flashing green light on the battery.If the charger cable is permanently stretched, it should be replaced inorder to minimize the risk of the cable getting stuck and breaking.NOTE! The lift cannot be used when the charger cable is plugged into a wall socket.Old batteries are to be deposited at the nearest recycling station or given to personnel authorizedby Liko.Golvo Classic • 7EN140106-0111 w w w . l i k o . com

Maximum LoadDifferent maximum loads may apply to different products on the assembled lift unit: lift, sling bar, sling and anyother accessories used. For the assembled lift unit, the maximum load is always the lowest maximum load ratingfor any of the components. For example, a Golvo which is approved for 200 kg (440 lbs) can be equipped with anaccessory which is approved for 300 kg (660 lbs). In this case, the maximum load of 200 kg (440 lbs) applies to theassembled lift unit. Take a look at the markings on the lift and lift accessories or contact Liko’s representative if youhave any queries.Recommended Lifting AccessoriesUsing lifting accessories other than those approved can entail a risk.Generally recommended sling bars and accessories for Golvo mobile lifts are described below.When changing a sling bar or other lifting accessories, the highest possible lifting height of the lift is affected.Before changing lifting accessories you should always ensure that the lift, after change, can fulfill the desiredlifting height in order to manage the lifting situations for which the lift is to be used.To select suitable slings and other lifting accessories, refer to the brochures “Golvo” and “Lifting accessories”.For additional guidance in selecting a sling, refer to the instruction guides for the respective sling models.Here, you will also find guidance for combining Liko’s sling bars with Liko’s slings.Contact your Liko representative or visit www.liko.com for advice and information on Liko’s product range.SlingBar Mini 220 Prod. No. 3156005Max 205 kg (450 lbs)Universal SlingBar 350* Prod. No. 3156074Max 300 kg (660 lbs)Universal SlingBar 450* Prod. No. 3156075(Standard on Golvo)Max 300 kg (660 lbs)Universal SlingBar 600* Prod. No. 3156076Max 300 kg (660 lbs)Universal TwinBar 670* Prod. No. 3156077Max 300 kg (660 lbs)Universal SideBars 450 Prod. No. 3156079including bagMax 300 kg (660 lbs)Sling Cross-bar 450* Prod. No. 3156021Max 300 kg (660 lbs)Sling Cross-bar 670* Prod. No. 3156018Max 300 kg (660 lbs)SlingBar Cover Paddy 30 Prod. No. 3607001(fits Universal SlingBars 350, 450 and 600,as well as SlingBar Slim 350)* also available equipped with Quick-Release HookGolvo Classic • 7EN140106-0112 w w w . l i k o . com

Bag for SlingBars Prod. No. 2001025Quick-Release HookLiko’s Quick-Release Hooks are a system for quick change of lifting accessorieson Liko’s mobile and stationary lifts. The Golvo must be equipped with Q-link inorder to be used with the Quick-release Hook.The Quick-Release Hook Universal fits the Universal SlingBar 350, 450 and 600(prod. no. 3156074 - 3156076). Quick-Release Hook TDM fits the SlingBar Mini220 (prod. no. 3156005), Sling Cross-bar 450 and 670 (prod. no. 3156021and 3156018) and Universal TwinBar 670 (prod. no. 3156077).See the “Guide to Liko’s Quick-Release Hook System”, which can bedownloaded from our website www.liko.com, or contact your Likorepresentative for more information on the advantages of the Quick-Release Hook system.Q-linkProd. No. 31590005Quick-release HookUniversalProd. No. 3156508Quick-release HookTDMProd. No. 3156502StretchersMost stretchers in Liko’s product range can be used in combination with Golvo.Contact your local Liko representative for more information.ScaleFor weighing patients in combination with Golvo, we recommendusing LikoScale 350 Max 350 kg (770 lbs).LikoScale 350 is certified according to the European DirectiveNAWI 90/384 (Non-Automatic Weighing Instruments).Contact your local Liko representative for more information.LikoScale 350Prod. No. 3156228Support Springs for Jump/Gait TrainingElastic springs are available as an accessory in order to produce asofter,springy motion, for example, during gait training.The springs are available in three different versions:Long, 28 cm (11 inch.), max 70 kg (154 lbs) user weight/pair Prod. No. 3156511Short, 22 cm (8.6 inch.), max 70 kg (154 lbs) user weight/pair Prod. No. 3156512Short, 22 cm (8.6 inch.), max 100 kg (220 lbs) user weight/pair Prod. No. 3156513See the instruction guides for Liko MasterVest,models 60 and 64 or Liko LiftPants model 92,for more information.Golvo Classic • 7EN140106-0113 w w w . l i k o . com

Leg Protector set GolvoGrey, pair, fits: Golvo 7000, 8000Grey, pair, fits: Golvo 7007, 8008Prod. No. 2006011GProd. No. 2006012GCord for HandControl IR Prod. No. 2006030Wall-mounted Battery Charger Prod. No. 2004108Extra battery Prod. No. 2006107Golvo Classic • 7EN140106-0114 w w w . l i k o . com

Simple TroubleshootingThe lift cannot be controlledvia HandControl IR.1. Check that the emergency stop has not been activated.2. Make sure that the charging cable is not connectedto an electric outlet.3. Check if HandControl IR indicates battery change.4. If the lift has been inactive for 24 hours, enable thesystem, press optional button on the operation panel.5. Make sure that the HandControl IR control is enabled.6. If the problem remains, see “The lift cannotbe controlled via the operation panel”, below.The lift cannot be controlledvia the operation panel.1. Make sure that the emergency stop has not beenactivated.2. Check that the charger cable is not connectedto an electric outlet.3. Check the battery capacity.4. Make sure that the cables to the control box areconnected correctly.5. Check that the battery’s contact plates are not defectiveor broken.6. If the problem remains, please contact Liko.The charger doesn’t work.1. Make sure that the emergency stop has not beenactivated.2. Make sure that the battery is properly attached.3. Check that the battery pack’s contact plates are notdefective or broken.4. If the problem remains, please contact Liko.The lift is stuck in the highposition.1. Make sure that the emergency stop has not beenactivated.2. Check the battery capacity.3. HandControl IR indicates battery change.4. Use the indicated electrical emergency loweringto lower the patient onto a firm surface.5. Use the indicated mechanical emergency loweringto lower the patient onto a firm surface.6. If the problem remains, please contact Liko.The lift does not reach maximumlifting height.1. Check that the lifting interval level is correctly set.2. If the problem remains, please contact Liko.If you hear unusual sounds.Contact Liko.Golvo Classic • 7EN140106-0115 w w w . l i k o . com

Inspection and MaintenanceCare and MaintenanceFor trouble-free use, certain details should be checked each day the lift is used:• Inspect the lift and check to make sure that there is no external damage.• Check the sling bar attachment.• Check the lift strap for wear, and ensure that the strap is not twisted.• Check the functionality of the safety latches.• Check the integrity of the lifting motion and the base-width adjustment.• Check that the lifting interval level is set correctly and that the emergency lowering is working as it should(both the electrical and the mechanical).• Charge the batteries each day the lift is used and make sure the charger works.When necessary, clean the lift with a moist cloth, using warm water or disinfectant and check that the wheels arefree from dirt. NOTE! Do not use cleaning agents that contain phenol or chlorine, since these can damagealuminium and polyamide material.The lift should not be exposed to running water.ServiceA periodic inspection of the lift should be carried out at least once a year.Periodic inspection, repair and maintenance may be performed only in accordance with the Liko servicemanual by personnel authorized by Liko and using original Liko spare parts.Service AgreementLiko offers the opportunity to enter into service contracts for the maintenance and regular inspection of yourLiko product.Expected Life TimeThe product has an expected life time of 10 years when correctly handled, serviced and periodically inspectedin accordance with Liko’s instructions.Transport and StorageDuring transportation, or when the lift is not to be used for a long time, the emergency stop should be engaged.The environment where the lift is transported and stored should have a temperature of 10 to 40 °C (50–104 °F)and a relative humidity of 30 to 75 %. The air pressure should be 700–1060 hPa.© Copyright Liko AB 2010-06RecyclingFor instructions on how to recycle your Liko product, please visit our website: www.liko.com.Product ChangesLiko’s products undergo continuous development, which is why we reserve the right to make product changeswithout prior notice. Contact your Liko representative for advice and information about product upgrades.Design and Quality by Liko in SwedenLiko is quality certified in accordance with ISO 9001 and its equivalent for the medical device industry, ISO 13485.Liko is also certified in accordance with environmental standard ISO 14001.www.liko.comManufacturer:Liko ABSE-975 92 LuleåSwedeninfo@liko.se