pipe clamps - heavy series

More documents

Recommendations

Info

pipe clampstechnical appendixrecommended distance between clampsclamp installation in case of bend pipeLThe values of the distancesof the clamps shown in the tableare indicative values, reportedto static loads.Pipe outsidediameter (mm)Distance L(m)Pipe outsidediameter (mm)Distance L6,0 - 13,5 1,0 114,0 - 168,0 5,013,5 - 18 1,2 168,0 - 219,0 6,018 - 32 1,5 219,0 - 324,0 6,732 - 38 2,0 324,0 - 356,0 7,038 - 57,2 2,7 356,0 - 406,0 7,557,2 - 75 3,0 406,0 - 480,0 8,075 - 76,1 3,5 481,0 550,0 8,576,1 - 88,9 3,7 551,0 - 630,0 9,088,9 - 102,0 4,0 631,0 - 716,0 10,0102,0 - 114,0 4,5 716,0 - 800,0 12,0(m)Bend pipes should be fixed by clamps immediatelybefore and after the bend.Morever it is recommended to design these clampsas fixed piont clamps.Joints is recommended for applicationswith the use of clamps before and after the junction.CodePI.EFFE.CI.C1THREAD CHARTConversion table and Metric thread / UNC threadSTANDARD SERIES HEAVY SERIES TWIN SERIESMetric threadUNC threadCodePI.EFFE.CI.CP1Metric threadUNC threadCodePI.EFFE.CI.C2 CP2 M10 3/8 - 16 UNC CF2C3 CP3 CF3C4 CP4 M12 7/16 - 14 UNC CF4C5 M6 1/4 - 20 UNC CP5 M16 5/8 - 11 UNC CF5C6 CP6 M20 3/4 - 10 UNCC7 CP7 M24 7/8 - 9 UNCC8 CP8 M30 11/8 - 7 UNCC9CP9CP10M3011/4 - 7 UNCMetric threadUNC threadCF1 M6 1/4 - 20 UNCM85/16 - 18 UNCPROPERTY CLASSES FOR BOLTS AND SCREWSACCESSORIES MATERIAL FINISHING CLASSSocket cap screwSteel Zinc plated/Untreated 8,8Stainless Steel --- A4-70Hexagon head boltSteel Zinc plated/Untreated 8,8Stainless Steel --- A4-70Safety washerSteel Zinc plated/Untreated 8Stainless Steel --- A4-70U-bolt nutSteel Zinc plated 8Stainless Steel --- A4-70 A2-70Flanged nut for U-boltsSteel Zinc plated 8Stainless Steel --- ---Washer for U-boltsSteel Zinc plated 100 HVStainless Steel --- A4-70 A2-70Nut bolt Steel Zinc plated 876
TEChnical appendixTightening Torques and Maximum Loads in Pipe DirectionTightening Torques and Maximum Loads in Pipe DirectionAll tightening torques and maximum loads in pipe direction regard clampswith upper plates and hexagon head bolts according to EN ISO 4014/4017.FThe value of the load F is an average value of testsperformed with steel tube Fe360.If the stress of the clamp in an axial direction of the pipe,the pipe slides into the clamp.Sliding starts when F value is reached.CodePI.EFFE.CI.C1Hexagon head bolt(EN ISO 4014/4017)Tighteningtorque(Nm)STANDARD SERIESPolypropylene Polyamide AluminiumMax load in pipedirection F(KN)Tighteningtorque(Nm)Max load in pipedirection F(KN)Tighteningtorque(Nm)Max load in pipedirection F(KN)8 0,7 10 0,7 12 3,6C2 8 1,2 10 0,9 12 4,3C3 8 1,5 10 1 12 4,4C4 8 1,7 10 1,8 12 4,8C5 M68 1,8 10 1,9 12 5,2C6 8 2 10 2,1 12 7,5C7 8 2,2 10 2,8 12 9C8 8 2,3 10 2,5 --- ---C9 8 2,4 10 2,5 --- ---CodePI.EFFE.CI.CP1Hexagon head bolt(EN ISO 4014/4017)Tighteningtorque(Nm)HEAVY SERIESPolypropylene Polyamide AluminiumMax load in pipedirection F(KN)Tighteningtorque(Nm)Max load in pipedirection F(KN)Tighteningtorque(Nm)Max load in pipedirection F(KN)13 1,8 21 4,5 32 13CP2 M1013 3 21 4,7 32 16CP3 15 3,5 25 5,2 37 16,5CP4 M12 30 8,5 40 9,5 55 30,5CP5 M16 46 11,5 56 27 125 36,5CP6 M20 80 15 155 25 225 62,5CP7 M24 110 30 200 34 250 71,7CP8190 41 360 50 500 86,5CP9 M30210 125 380 130 500 190,5CP10 270 168 450 180 600 244,5CodePI.EFFE.CI.Hexagon head bolt(EN ISO 4014/4017)Tightening torque(Nm)PolypropyleneTWIN SERIESMax load in pipe direction F(KN)Tightening torque(Nm)PolyamideMax load in pipe direction F(KN)CF1 M6 6 1,1 6 1,1CF213 2,5 13 2,5CF3 13 2,1 13 2,1M8CF4 13 2,9 13 3,1CF5 9 2,2 9 2,777
Page 3 and 4:
Pi.Effe.Ci.Over 35 yearsof experien
Page 5 and 6:
STANDARDSeriesClamps• Order Codes
Page 7 and 8:
pipe clamps - standard seriesOrder
Page 10:
pipe clamps - standard seriesDimens
Page 13 and 14:
pipe clamps - standard seriesMounti
Page 17 and 18:
pipe clamps - heavy seriesOrder Cod
Page 20 and 21:
pipe clamps - heavy seriesDimension
Page 22 and 23:
Page 24 and 25:
Page 27 and 28: TWIN SeriesClampstwin series clamps
Page 30 and 31: pipe clamps - twin seriesDimensions
Page 32 and 33: pipe clamps - twin seriesDimensions
Page 34 and 35: pipe clamps - twin seriesMounting E
Page 36 and 37: standard series clamps with rubber
Page 38 and 39: clamps with rubber bushingMounting
Page 40 and 41: standard series clamps for twin pip
Page 42 and 43: standard series with spaced platesO
Page 44 and 45: standard and twin series with space
Page 46 and 47: clamps with mounting rail 40x22Orde
Page 49 and 50: Special Clampsspecial clamps• Ord
Page 51 and 52: special clampsOrder Codes and Dimen
Page 53 and 54: HEAVY SeriesTWIN DESIGN Clamps• O
Page 55 and 56: LIGHT SeriesClampslight series clam
Page 57: PIPE CLMAPS - light seriesOrder Cod
Page 60 and 61: special clamps for industrial elect
Page 62 and 63: super heavyweight seriesElectro-wel
Page 64 and 65: light series u-boltType BCLight ser
Page 66 and 67: medium series u-boltType BCMedium s
Page 68 and 69: heavy series u-boltType BCHeavy ser
Page 70 and 71: ØD1round steel u-bolt according to
Page 72: light and medium squared U-boltOrde
Page 76 and 77: materialcharacteristicsclamp bodyma
Page 81 and 82: Tool for Weldingof Platestool for w
Page 84: a worldwidepresencemain office and
show all

pipe clamps - heavy series

Create successful ePaper yourself

Delete template?

Save as template?