ncr/doc/Kiosks/TechnicalManuals/7401_Kiosk_Sit... - Alsys Data

More documents

Recommendations

Info

52 Site Preparation15-inch LCD No-Cabinet Feature7401-F757The 15-inch LCD No-Cabinet Feature (F757) is purchased by customerswho design their own enclosures to meet their specific needs. Thissection provides information that must be considered when designingenclosures.Installation Guidelines• To prevent moisture from entering system, the front of the displaymust be in close contact with the opening in the enclosure.• Within every custom enclosure, the Electronics Box Back CoverMUST remain installed because it helps dissipate the heatgenerated by the CPU.• Adequate ventilation must be provided in every custom enclosure.The maximum allowable ambient temperature within anyenclosure is 45 o C (113 o F).• To prevent accidental shorts, the power supply and any otherperipheral within the enclosure must be mounted securely andwithin reach of the display’s connectors.• This feature comes with a motion sensor that is at the end of a381 mm (15 in.) cable. When using the motion sensor, it must bemounted between 25 and 76 mm (1 to 3 in.) below the bottom of thedisplay and centered along the width of the display.• Compliance of this device with regulatory requirements must beverified in the end-use application.• This device is a component which requires a suitable enclosure inits end-use application. The end-use product in which thiscomponent is used should be certified in accordance with UL 1950,EN60950, IEC950 or other applicable safety standard.Caution: NCR displays are not designed for horizontal or inverteduse. NCR displays must be mounted no more than 40 o forward orbackward from horizontal. Failure to follow this guideline could resultin overheating.
Site Preparation 53Mounting Specification IllustrationsThe following illustration shows the minimum allowable dimensionsfor the display opening when the optional cosmetic bezel is used.OPTIONAL COSMETIC BEZELGASKET MUST MEET INSIDE SURFACEOF CUSTOM DISPLAY OPENING.(OPTIONAL COSMETIC GASKET NOT USEDIF OPTIONAL BEZEL IS NOT USED).348.7 mm3.730 in. 4.2 mm.165 in.9.4 mm.372 in.270 mm10.630 in.FRONT SURFACE OF DISPLAY BEZEL (IF USED)MUST PROTRUDE THROUGH ENCLOSURE. GASKETMUST MEET INSIDE SURFACE OF CUSTOMAPPLICATION'S DISPLAY OPENING. THIS ISTO PROVIDE A SECURE AND WATERTIGHT FIT.USE 4 #8-32 MACHINE SCREWS INCORNERS OF UNIT TO MOUNT DISPLAYINTO ENCLOSURE. 8 TOTAL SCREWSMAY BE USED FOR MULTIPLE MOUNTINGCONFIGURATIONS.345.4 mm13.600 in.156.2 mm6.150 in.175 mm6.888 in.141.6 mm5.575 in.292.4 mm11.510 in.22.9 mm.900 in.200.7 mm7.900 in.17.2 mm.678 in.19100
Page 1 and 2:
N CRNCR EasyPoint 7401Release 2.5Si
Page 3 and 4:
Site PreparationiPrefaceSafety Requ
Page 5 and 6:
Site PreparationiiiAbout this BookG
Page 7 and 8:
Site PreparationvReferences• NCR
Page 9 and 10:
Site PreparationviiTable of Content
Page 11 and 12:
Site PreparationixCable Routing Con
Page 13 and 14:
Site PreparationxiRevision RecordIs
Page 15 and 16:
Site PreparationxiiiInternational R
Page 17 and 18:
Site PreparationxvDeclaration of Co
Page 19 and 20: Site PreparationIntroduction7401-2x
Page 21 and 22: Site Preparation 3Interpreting the
Page 23 and 24: Site Preparation 5Customer Responsi
Page 25 and 26: Site Preparation 77401-2xxx and 3xx
Page 27 and 28: Site Preparation 97401-2xxx and 3xx
Page 29 and 30: Site Preparation 11Operating and Se
Page 31 and 32: Site Preparation 137401-22xx/26xx T
Page 33 and 34: Site Preparation 157401-25xx/26xx (
Page 35 and 36: Site Preparation 177401-K540 (12.1
Page 37 and 38: Site Preparation 197401-K580/590 w/
Page 39 and 40: Site Preparation 217401 with 2336-K
Page 41 and 42: Site Preparation 23EasyPoint 45 Ped
Page 43 and 44: Site Preparation 25NCR 2189 Cash Dr
Page 45 and 46: Site Preparation 277196 Thermal Rec
Page 47 and 48: Site Preparation 29Component Weight
Page 49 and 50: Site Preparation 317401 Power Requi
Page 51 and 52: Site Preparation 33Power Consumptio
Page 53 and 54: Site Preparation 35Cable Routing Co
Page 55 and 56: Site Preparation 377401-4xxxExterna
Page 57 and 58: Site Preparation 39Terminal with K5
Page 59 and 60: Site Preparation 41Terminal with K5
Page 61 and 62: Site Preparation 43Lag Screws (6)1.
Page 63 and 64: Site Preparation 45Printer Only Mou
Page 65 and 66: Site Preparation 47Considerations f
Page 67 and 68: Site Preparation 4912.1-inch LCD No
Page 69: Site Preparation 51Mounting Specifi
Page 73 and 74: Site Preparation 55K/F 502 Flush Wa
Page 75 and 76: Site Preparation 577401-4xxx Mounti
Page 77 and 78: Site Preparation 597401-4xxx EasyPo
Page 79 and 80: Site Preparation 61System CablesCab
Page 81 and 82: Site Preparation 63Cable Illustrati
Page 83 and 84: Site Preparation 65External Paralle
Page 85 and 86: Appendix A: Transient ProtectionAC
Page 87 and 88: Index—1—12.1 Inch LCD No-Cabine
Page 90: B005-0000-1255 Dec 2002 Printed on
show all

ncr/doc/Kiosks/TechnicalManuals/7401_Kiosk_Sit... - Alsys Data

Create successful ePaper yourself

Delete template?

Save as template?