iG5A, product manual - H2flow

More documents

Recommendations

Info

Note that setting Frequency Ref. for Accel/decel (H70) is set to Max Freq and target freq is setbelow Max freq. the shape of S-curve may be distorted.Accel/decelRef FreqTarget FreqFreqH17H18H17H18CAUTIONIf Target Frequency isbelow Max Frequency, thewaveform will be shownwith the top portion cut out. Accel time for S-curve settingH17 H18= ACC + ACC × + ACC ×22 Decel time for S-curve settingH17 H18= dEC + dEC × + dEC ×22 ACC, dEC indicate the set time in Drive group.• Accel/Decel DisableGroup Code Parameter Name Setting Range Initial Unit[Multi-function input terminal0 ~27I/O group I17- 0P1 define]~ ~I24[Multi-function inputterminal P8 define]247• Select one terminal among Multi-function input terminals 1-8 to define Accel/Decel disable.• If P8 is selected, set I24 to 24 to activate this function.Freq.P8Operatingcommand7-16
7.5 V/F control• Linear V/F pattern operationGroup Code Parameter Name Setting Range Initial UnitFunction group 1 F22 [Base frequency] - 30 ~ 400 60.00 HzF23 [Start frequency] - 0.1 ~ 10.0 0.50 HzF30 [V/F pattern] 0 0 ~ 2 0Function group 2 H40 [Control mode select] - 0 ~ 3 0• Set F30 to 0 {Linear}.• This pattern maintains a linear Volts/frequency ratio from F23 - [Start frequency] to F22-[Base frequency]. This is appropriate for constant torque applications. Base Frequency: Inverter outputs its rated voltage at this level. Enter the motor nameplatefrequency. Start Frequency: Inverter starts to output its voltage at this level.Base freq.Freq.Start freq.Inverter ratedvoltageVoltageRuncommand• Square V/F patternGroup Code Parameter Name Setting Range Initial UnitFunctiongroup 1F30 [V/F pattern] 1 0 ~ 2 0• Set F30 to 1{Square}.• This pattern maintains squared volts/hertz ratio. Appropriate applications are fans, pumps,etc.100%VoltageBase freq.Freq.7-17
Page 2 and 3:
Thank you for purchasing LS Variabl
Page 4 and 5:
OPERATING PRECAUTIONS(1) Handling a
Page 6 and 7:
Important User Information• The p
Page 8 and 9:
8.4 3-Wire ........................
Page 10 and 11:
CHAPTER 1 - BASIC INFORMATION & PRE
Page 12 and 13:
1.3 Product assembling & disassembl
Page 14 and 15:
CHAPTER 2 - INSTALLATION & WIRING2.
Page 16 and 17:
2.2 DimensionsSV004IG5A-1SV004iG5A-
Page 18 and 19:
SV110iG5A-2 /SV150iG5A-2SV110iG5A-4
Page 20 and 21:
2.3 Terminal wiring (Control I/O)T/
Page 22 and 23:
2.4 Specifications for power termin
Page 24 and 25:
WARNING• Use the Type 3 grounding
Page 26 and 27:
2.6 PNP/NPN selection and connector
Page 28 and 29:
3.2 Recommended MCCBInverterCapacit
Page 30 and 31:
CHAPTER 4 - PROGRAMMING KEYPAD & BA
Page 32 and 33:
4.3 Moving to other groups• There
Page 34 and 35:
4.4 How to change the codes in a gr
Page 36 and 37:
4.5 Parameter setting• Changing p
Page 43 and 44: • Frequency Setting via potentiom
Page 45 and 46: CHAPTER 5 - FUNCTION LIST• Drive
Page 47 and 48: • Function group 1LEDdisplayAddre
Page 55 and 56: • Function group 2LEDdisplayH221)
Page 63 and 64: • Input/output groupLEDdisplayAdd
Page 65 and 66: • Input/output groupLEDdisplayAdd
Page 67 and 68: • Input/Output GroupLEDdisplayAdd
Page 69: • Input/Output GroupLEDdisplayAdd
Page 72 and 73: 6.1 Frequency setting1st ReferenceF
Page 75 and 76: 6.3 Accel/Decel setting and V/F con
Page 77 and 78: CHAPTER 7 - BASIC FUNCTIONS7.1 Freq
Page 79 and 80: I6 ~ I10: Setting input range and c
Page 81 and 82: Group Code Parameter Name Setting U
Page 83 and 84: 7.2 Multi-Step Frequency settingGro
Page 85 and 86: • Operating command via FX, RX te
Page 87 and 88: • Power On Start selectGroup Code
Page 89 and 90: More precise time unit can be set c
Page 91: • Accel/Decel pattern settingGrou
Page 95 and 96: • Manual torque boostGroup Code P
Page 97 and 98: 7.7 Frequency limit• Frequency li
Page 99 and 100: CHAPTER 8 - ADVANCED FUNCTIONS8.1 D
Page 101 and 102: 8.2 Jog operation• Terminal jog o
Page 103 and 104: • Up-down mode selectGroup Displa
Page 105 and 106: 8.4 3-WireGroup Display Parameter N
Page 107 and 108: H33: Enter the motor nameplate rate
Page 109 and 110: • Normal PID drive (H54=0)PID con
Page 111 and 112: Sleep FreqWake up levelPID Referenc
Page 113 and 114: • Factory default by motor rating
Page 115 and 116: EX) Speed search during Instant Pow
Page 117 and 118: 8.13 Operating sound select (Carrie
Page 119 and 120: 8.15 Self-Diagnostic function• Ho
Page 121 and 122: Selects the self drive in the 2 nd
Page 123 and 124: Selects the self drive in the 2 nd
Page 125 and 126: Select 1 and 2 for F70The center va
Page 127 and 128: CAUTIONIf operation is continued af
Page 129 and 130: 8.25 Parameter Initialize / Lock•
Page 131 and 132: CHAPTER 9 - MONITORING9.1 Operating
Page 133 and 134: 9.2 Monitoring the I/O terminal•
Page 135 and 136: When the fault condition is reset v
Page 137 and 138: 9.5 Multi-function output terminal
Page 139 and 140: • 2: FDT-3 Activated when run fre
Page 141 and 142: • 12: During operation Activated
Page 143 and 144:
CHAPTER 10 -PROTECTIVE FUNCTIONS10.
Page 145 and 146:
• Overload tripGroup Code Paramet
Page 147 and 148:
10.4 Output phase loss protectionGr
Page 149 and 150:
Ex 1) The inverter determines the f
Page 151 and 152:
CHAPTER 11 -RS485 COMMUNICATION11.1
Page 153 and 154:
11.5 Communication protocol (MODBUS
Page 155 and 156:
2.1) Acknowledge response:ACK Drive
Page 157 and 158:
Address Parameter Scale Unit R/W Al
Page 159 and 160:
2) Extended Common Area :2.1) Inver
Page 161 and 162:
2.3) Inverter Memory Control Area (
Page 163 and 164:
CHAPTER 12 -TROUBLESHOOTING & MAINT
Page 165 and 166:
12.2 Fault remedyKeypaddisplayOverc
Page 167 and 168:
• Fault remedyProtective function
Page 169 and 170:
CHAPTER 13 -SPECIFICATIONS13.1 Tech
Page 171 and 172:
• OperationOperation modeFrequenc
Page 173 and 174:
2) Remote Cable (1M,2M,3M,5M)• Re
Page 175 and 176:
• Conduit KitConduit KitInverter
Page 177 and 178:
DECLARATION OF CONFORMITYCouncil Di
Page 179 and 180:
EMI / RFI POWER LINE FILTERSLS inve
Page 182:
WarrantyMakerModel No.CustomerInfor
show all

iG5A, product manual - H2flow

Create successful ePaper yourself

Delete template?

Save as template?