iG5A, product manual - H2flow

More documents

Recommendations

Info

TECHNICAL STANDARDS APPLIEDThe standards applied in order to comply with the essential requirements of the Directives2006/95/CE "Electrical material intended to be used with certain limits of voltage" and 2004/108/CE"Electromagnetic Compatibility" are the following ones:• EN 50178 (1997)•EN 61800-3 (2004)• EN 55011/A2 (2003)•EN61000-4-2/A2 (2001)•EN61000-4-3/A2 (2004)•EN61000-4-4/A2 (2002)•EN61000-4-5/A1 (2001)•EN61000-4-6/A1 (2001)“Electronic equipment for use in power installations”.“Adjustable speed electrical power drive systems. Part 3: EMCproduct standard including specific methods”“Industrial, scientific and medical (ISM) radio-frequencyequipment. Radio disturbances characteristics. Limits andmethods of measurement”“Electromagnetic compatibility (EMC). Part 4: Testing andmeasurement techniques. Section 2: Electrostatic dischargeimmunity test.“Electromagnetic compatibility (EMC). Part 4: Testing andmeasurement techniques. Section 3: Radiated, radiofrequency,electromagnetic field immunity test.“Electromagnetic compatibility (EMC). Part 4: Testing andmeasurement techniques. Section 4: Electrical fast transients /burst immunity test.“Electromagnetic compatibility (EMC). Part 4: Testing andmeasurement techniques. Section 5: Surge immunity test.“Electromagnetic compatibility (EMC). Part 4: Testing andmeasurement techniques. Section 6: Immunity to conducteddisturbances, induced by radio-frequency fields.•CEI/TR 61000-2-1 (1990) “Electromagnetic compatibility (EMC). Part 2: Environment.Environment description for low-frequency conducteddisturbances and signalling in public low voltages supplysystems”• EN 61000-2-2 (2003)• EN 61000-2-4 (1997)•EN60146-1-1/A1 (1998)“Electromagnetic compatibility (EMC). Part 2: Environment.Compatibility level for low-frequency conducted disturbances andsignalling in public low voltages supply systems”“Electromagnetic compatibility (EMC). Part 2: Environment.Compatibility level in industrial plants for low-frequencyconducted disturbances”“Semiconductor convertors. General requirments and linecommutated convertors. Part 1-1: Specifications of basicrequirements”ii
EMI / RFI POWER LINE FILTERSLS inverters, iG5A seriesRFI FILTERSTHE LS RANGE OF POWER LINE FILTERS FF ( Footprint ) - FE ( Standard ) SERIES, HAVE BEEN SPECIFICALLYDESIGNED WITH HIGH FREQUENCY LS INVERTERS. THE USE OF LS FILTERS, WITH THE INSTALLATION ADVICEOVERLEAF HELP TO ENSURE TROUBLE FREE USE ALONG SIDE SENSITIVE DEVICES AND COMPLIANCE TOCONDUCTED EMISSION AND IMMUNITY STANDARS TO EN 50081 -> EN61000-6-3:02 and EN61000-6-1:02CAUTIONIN CASE OF A LEAKAGE CURRENT PROTECTIVE DEVICES IS USED ON POWER SUPPLY, IT MAY BE FAULT ATPOWER-ON OR OFF. IN AVOID THIS CASE, THE SENSE CURRENT OF PROTECTIVE DEVICE SHOULD BE LARGERTHAN VALUE OF LEAKAGE CURRENT AT WORST CASE IN THE BELOW TABLE.RECOMMENDED INSTALLATION INSTRUCTIONSTo conform to the EMC directive, it is necessary that these instructions be followed as closely as possible.Follow the usual safety procedures when working with electrical equipment. All electrical connections to thefilter, inverter and motor must be made by a qualified electrical technician.1-) Check the filter rating label to ensure that the current, voltage rating and part number are correct.2-) For best results the filter should be fitted as closely as possible to the incoming mains supply of the wiring enclousure,usually directly after the enclousures circuit breaker or supply switch.3-) The back panel of the wiring cabinet of board should be prepared for the mounting dimensions of the filter. Careshould be taken to remove any paint etc... from the mounting holes and face area of the panel to ensure the best possibleearthing of the filter.4-) Mount the filter securely.5-) Connect the mains supply to the filter terminals marked LINE, connect any earth cables to the earth stud provided.Connect the filter terminals marked LOAD to the mains input of the inverter using short lengths of appropriate gaugecable.6-) Connect the motor and fit the ferrite core ( output chokes ) as close to the inverter as possible. Armoured or screenedcable should be used with the 3 phase conductors only threaded twice through the center of the ferrite core. The earthconductor should be securely earthed at both inverter and motor ends. The screen should be connected to the enclosurebody via and earthed cable gland.7-) Connect any control cables as instructed in the inverter instructions manual.IT IS IMPORTANT THAT ALL LEAD LENGHTS ARE KEPT AS SHORT AS POSSIBLE AND THAT INCOMING MAINSAND OUTGOING MOTOR CABLES ARE KEPT WELL SEPARATED.FF SERIES ( Footprint )INVERTERSHIELDED CABLEMOTORFE SERIES ( Standard )FILTERFILTERINVERTERSHIELDED CABLEMOTORiii
Page 2 and 3:
Thank you for purchasing LS Variabl
Page 4 and 5:
OPERATING PRECAUTIONS(1) Handling a
Page 6 and 7:
Important User Information• The p
Page 8 and 9:
8.4 3-Wire ........................
Page 10 and 11:
CHAPTER 1 - BASIC INFORMATION & PRE
Page 12 and 13:
1.3 Product assembling & disassembl
Page 14 and 15:
CHAPTER 2 - INSTALLATION & WIRING2.
Page 16 and 17:
2.2 DimensionsSV004IG5A-1SV004iG5A-
Page 18 and 19:
SV110iG5A-2 /SV150iG5A-2SV110iG5A-4
Page 20 and 21:
2.3 Terminal wiring (Control I/O)T/
Page 22 and 23:
2.4 Specifications for power termin
Page 24 and 25:
WARNING• Use the Type 3 grounding
Page 26 and 27:
2.6 PNP/NPN selection and connector
Page 28 and 29:
3.2 Recommended MCCBInverterCapacit
Page 30 and 31:
CHAPTER 4 - PROGRAMMING KEYPAD & BA
Page 32 and 33:
4.3 Moving to other groups• There
Page 34 and 35:
4.4 How to change the codes in a gr
Page 36 and 37:
4.5 Parameter setting• Changing p
Page 43 and 44:
• Frequency Setting via potentiom
Page 45 and 46:
CHAPTER 5 - FUNCTION LIST• Drive
Page 47 and 48:
• Function group 1LEDdisplayAddre
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
• Function group 2LEDdisplayH221)
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
• Input/output groupLEDdisplayAdd
Page 65 and 66:
• Input/output groupLEDdisplayAdd
Page 67 and 68:
• Input/Output GroupLEDdisplayAdd
Page 69:
• Input/Output GroupLEDdisplayAdd
Page 72 and 73:
6.1 Frequency setting1st ReferenceF
Page 75 and 76:
6.3 Accel/Decel setting and V/F con
Page 77 and 78:
CHAPTER 7 - BASIC FUNCTIONS7.1 Freq
Page 79 and 80:
I6 ~ I10: Setting input range and c
Page 81 and 82:
Group Code Parameter Name Setting U
Page 83 and 84:
7.2 Multi-Step Frequency settingGro
Page 85 and 86:
• Operating command via FX, RX te
Page 87 and 88:
• Power On Start selectGroup Code
Page 89 and 90:
More precise time unit can be set c
Page 91 and 92:
• Accel/Decel pattern settingGrou
Page 93 and 94:
7.5 V/F control• Linear V/F patte
Page 95 and 96:
• Manual torque boostGroup Code P
Page 97 and 98:
7.7 Frequency limit• Frequency li
Page 99 and 100:
CHAPTER 8 - ADVANCED FUNCTIONS8.1 D
Page 101 and 102:
8.2 Jog operation• Terminal jog o
Page 103 and 104:
• Up-down mode selectGroup Displa
Page 105 and 106:
8.4 3-WireGroup Display Parameter N
Page 107 and 108:
H33: Enter the motor nameplate rate
Page 109 and 110:
• Normal PID drive (H54=0)PID con
Page 111 and 112:
Sleep FreqWake up levelPID Referenc
Page 113 and 114:
• Factory default by motor rating
Page 115 and 116:
EX) Speed search during Instant Pow
Page 117 and 118:
8.13 Operating sound select (Carrie
Page 119 and 120:
8.15 Self-Diagnostic function• Ho
Page 121 and 122:
Selects the self drive in the 2 nd
Page 123 and 124:
Selects the self drive in the 2 nd
Page 125 and 126:
Select 1 and 2 for F70The center va
Page 127 and 128: CAUTIONIf operation is continued af
Page 129 and 130: 8.25 Parameter Initialize / Lock•
Page 131 and 132: CHAPTER 9 - MONITORING9.1 Operating
Page 133 and 134: 9.2 Monitoring the I/O terminal•
Page 135 and 136: When the fault condition is reset v
Page 137 and 138: 9.5 Multi-function output terminal
Page 139 and 140: • 2: FDT-3 Activated when run fre
Page 141 and 142: • 12: During operation Activated
Page 143 and 144: CHAPTER 10 -PROTECTIVE FUNCTIONS10.
Page 145 and 146: • Overload tripGroup Code Paramet
Page 147 and 148: 10.4 Output phase loss protectionGr
Page 149 and 150: Ex 1) The inverter determines the f
Page 151 and 152: CHAPTER 11 -RS485 COMMUNICATION11.1
Page 153 and 154: 11.5 Communication protocol (MODBUS
Page 155 and 156: 2.1) Acknowledge response:ACK Drive
Page 157 and 158: Address Parameter Scale Unit R/W Al
Page 159 and 160: 2) Extended Common Area :2.1) Inver
Page 161 and 162: 2.3) Inverter Memory Control Area (
Page 163 and 164: CHAPTER 12 -TROUBLESHOOTING & MAINT
Page 165 and 166: 12.2 Fault remedyKeypaddisplayOverc
Page 167 and 168: • Fault remedyProtective function
Page 169 and 170: CHAPTER 13 -SPECIFICATIONS13.1 Tech
Page 171 and 172: • OperationOperation modeFrequenc
Page 173 and 174: 2) Remote Cable (1M,2M,3M,5M)• Re
Page 175 and 176: • Conduit KitConduit KitInverter
Page 177: DECLARATION OF CONFORMITYCouncil Di
Page 182: WarrantyMakerModel No.CustomerInfor
show all

iG5A, product manual - H2flow

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?