iG5A, product manual - H2flow

More documents

Recommendations

Info

CHAPTER 2 - INSTALLATION & WIRING2.1 Installation precautionsCAUTION• Handle the inverter with care to prevent damage to the plastic components. Do not hold theinverter by the front cover. It may fall off.• Install the inverter in a place where it is immune to vibration (5.9 m/s 2 or less).• Install in a location where temperature is within the permissible range (-10~50°C).• The inverter will be very hot during operation. Install it on a non-combustible surface.• Mount the inverter on a flat, vertical and level surface. Inverter orientation must be vertical(top up) for proper heat dissipation. Also leave sufficient clearances around the inverter.10cm MinLeave space enough toallow cooled air flowingeasily between wiringduct and the unitCooling air5cmMin5cmMin10cm MinVentilating fan• Protect from moisture and direct sunlight.• Do not install the inverter in any environment where it is exposed to waterdrops, oil mist,dust, etc. Install the inverter in a clean place or inside a “totally enclosed” panel anysuspended matter is not entered.2-1
• When two or more inverters are installed or a cooling fan is mounted in a panel, the invertersand fan must be installed in proper positions with extreme care to keep the ambienttemperature below the permissible range.• Installed the inverter using screws or bolts to insure the inverter is firmly fastened.< For installing multiple inverters in a panel>Heat (NG)CAUTIONTake caution on proper heat ventilation when installing inverters and fans in a panel.2-2
Page 2 and 3: Thank you for purchasing LS Variabl
Page 4 and 5: OPERATING PRECAUTIONS(1) Handling a
Page 6 and 7: Important User Information• The p
Page 8 and 9: 8.4 3-Wire ........................
Page 10 and 11: CHAPTER 1 - BASIC INFORMATION & PRE
Page 12 and 13: 1.3 Product assembling & disassembl
Page 16 and 17: 2.2 DimensionsSV004IG5A-1SV004iG5A-
Page 18 and 19: SV110iG5A-2 /SV150iG5A-2SV110iG5A-4
Page 20 and 21: 2.3 Terminal wiring (Control I/O)T/
Page 22 and 23: 2.4 Specifications for power termin
Page 24 and 25: WARNING• Use the Type 3 grounding
Page 26 and 27: 2.6 PNP/NPN selection and connector
Page 28 and 29: 3.2 Recommended MCCBInverterCapacit
Page 30 and 31: CHAPTER 4 - PROGRAMMING KEYPAD & BA
Page 32 and 33: 4.3 Moving to other groups• There
Page 34 and 35: 4.4 How to change the codes in a gr
Page 36 and 37: 4.5 Parameter setting• Changing p
Page 43 and 44: • Frequency Setting via potentiom
Page 45 and 46: CHAPTER 5 - FUNCTION LIST• Drive
Page 47 and 48: • Function group 1LEDdisplayAddre
Page 55 and 56: • Function group 2LEDdisplayH221)
Page 63 and 64: • Input/output groupLEDdisplayAdd
Page 65 and 66:
• Input/output groupLEDdisplayAdd
Page 67 and 68:
• Input/Output GroupLEDdisplayAdd
Page 69:
• Input/Output GroupLEDdisplayAdd
Page 72 and 73:
6.1 Frequency setting1st ReferenceF
Page 75 and 76:
6.3 Accel/Decel setting and V/F con
Page 77 and 78:
CHAPTER 7 - BASIC FUNCTIONS7.1 Freq
Page 79 and 80:
I6 ~ I10: Setting input range and c
Page 81 and 82:
Group Code Parameter Name Setting U
Page 83 and 84:
7.2 Multi-Step Frequency settingGro
Page 85 and 86:
• Operating command via FX, RX te
Page 87 and 88:
• Power On Start selectGroup Code
Page 89 and 90:
More precise time unit can be set c
Page 91 and 92:
• Accel/Decel pattern settingGrou
Page 93 and 94:
7.5 V/F control• Linear V/F patte
Page 95 and 96:
• Manual torque boostGroup Code P
Page 97 and 98:
7.7 Frequency limit• Frequency li
Page 99 and 100:
CHAPTER 8 - ADVANCED FUNCTIONS8.1 D
Page 101 and 102:
8.2 Jog operation• Terminal jog o
Page 103 and 104:
• Up-down mode selectGroup Displa
Page 105 and 106:
8.4 3-WireGroup Display Parameter N
Page 107 and 108:
H33: Enter the motor nameplate rate
Page 109 and 110:
• Normal PID drive (H54=0)PID con
Page 111 and 112:
Sleep FreqWake up levelPID Referenc
Page 113 and 114:
• Factory default by motor rating
Page 115 and 116:
EX) Speed search during Instant Pow
Page 117 and 118:
8.13 Operating sound select (Carrie
Page 119 and 120:
8.15 Self-Diagnostic function• Ho
Page 121 and 122:
Selects the self drive in the 2 nd
Page 123 and 124:
Selects the self drive in the 2 nd
Page 125 and 126:
Select 1 and 2 for F70The center va
Page 127 and 128:
CAUTIONIf operation is continued af
Page 129 and 130:
8.25 Parameter Initialize / Lock•
Page 131 and 132:
CHAPTER 9 - MONITORING9.1 Operating
Page 133 and 134:
9.2 Monitoring the I/O terminal•
Page 135 and 136:
When the fault condition is reset v
Page 137 and 138:
9.5 Multi-function output terminal
Page 139 and 140:
• 2: FDT-3 Activated when run fre
Page 141 and 142:
• 12: During operation Activated
Page 143 and 144:
CHAPTER 10 -PROTECTIVE FUNCTIONS10.
Page 145 and 146:
• Overload tripGroup Code Paramet
Page 147 and 148:
10.4 Output phase loss protectionGr
Page 149 and 150:
Ex 1) The inverter determines the f
Page 151 and 152:
CHAPTER 11 -RS485 COMMUNICATION11.1
Page 153 and 154:
11.5 Communication protocol (MODBUS
Page 155 and 156:
2.1) Acknowledge response:ACK Drive
Page 157 and 158:
Address Parameter Scale Unit R/W Al
Page 159 and 160:
2) Extended Common Area :2.1) Inver
Page 161 and 162:
2.3) Inverter Memory Control Area (
Page 163 and 164:
CHAPTER 12 -TROUBLESHOOTING & MAINT
Page 165 and 166:
12.2 Fault remedyKeypaddisplayOverc
Page 167 and 168:
• Fault remedyProtective function
Page 169 and 170:
CHAPTER 13 -SPECIFICATIONS13.1 Tech
Page 171 and 172:
• OperationOperation modeFrequenc
Page 173 and 174:
2) Remote Cable (1M,2M,3M,5M)• Re
Page 175 and 176:
• Conduit KitConduit KitInverter
Page 177 and 178:
DECLARATION OF CONFORMITYCouncil Di
Page 179 and 180:
EMI / RFI POWER LINE FILTERSLS inve
Page 182:
WarrantyMakerModel No.CustomerInfor
show all

iG5A, product manual - H2flow

Create successful ePaper yourself

Delete template?

Save as template?