Technical Service Manual - mbm-Service GmbH

More documents

Recommendations

Info

INSTALLATION INSTRUCTION FLORAL CASE BAFFLE INSTALLATION The baffle is installed on floral cabinets to slow the velocity of the air down. This will make the flowers last longer, because the pedals do not dry out as quickly. 1. Trim a small square out of top left side of baffle to accommodate the suction line. 2. Place baffle in place and install #6 x 1/2 screws into 1/2” lip of the baffle and top of cabinet. 3. Install #6 x 1/2 screws into 1/2” lip and evaporator cover being careful not to puncture evaporator drain pan. Baffle 38 Evaporator Housing
REQUIRED TOOLS • 1/16" Drill • 1/8" - 1/4" Shim (2) • Socket wrench ____________ STEP 1 ____________ Remove all products and shelving from interior of cabinet. ____________ STEP 2 ____________ Disconnect power to the unit. ____________ STEP 3 ____________ Wipe interior of cooler with a clean dry cloth to remove dirt and moisture. Surface must be clean and dry for adhesive on extrusions (mirror support strips). ____________ STEP 4 ____________ Measure 15/16" from rear interior wall forward and mark the side wall for the mirror support strip location. Select two shims of equal height between 1/8" - 1/4 (one for each side of the cabinet). Measure and mark the height of the shim against the side wall. Repeat on the opposite wall (see figure 1 & 3). ____________ STEP 5 ____________ Locate two channel extrusions (mirror support strips). Remove paper strip covering adhesive from one of the mirror support strips. ____ STEP 6 _____ Carefully secure mirror support strip against the side wall the height of the shim mark and along the mark 15/16" from the back wall. INSTALLATION INSTRUCTION GDM-23FC Mirror Retrofit Kit 5/16” Figure 2. Repeat on the opposite wall (adhesive backing is the only anchor for the mirror supports. ____________ STEP 7 ____________ Place shims on the interior floor in line to support the mirror when in position. ____________ STEP 8 ____________ Slip one edge of the mirror in the mirror support strip channel, bow mirror and feed into the other mirror support strip. Work until mirror fits flat inside support strips and rests on top of the floor shims (see figure 2). ____________ STEP 9 ____________ Locate left edge of the drain line Figure 1. cover at the rear of the cabinet. At the top edge of the mirror measure in 1" and down 2". Mark center point. At the bottom edge of the mirror measure in 1" from the drain line cover and up 2" from the bottom edge of the mirror. Mark center point. (see figure 3). NOTE If the drain line cover edge at the tank bottom is difficult to locate measure the distance from the side wall to the center point at the top of the mirror and use that measurement for the bottom center point. ____________ STEP 10 ____________ Drill pilot holes at both center points with a 1/16" drill bit through the mirror and drain line cover. ______ STEP 11 _____ Fasten 10-16 x 1/2 hex knurled head screw (included) in both pilot holes snug against mirror. 39 WARNING Do not over tighten screw to avoid cracking mirror. ____________ STEP 12 ____________ Remove shims, replace shelving and reconnect power to cabinet. Figure 3. 2 1 shims 2 1 drain line cover
Page 1 and 2: Technical Service Manual (All Model
Page 3 and 4: Index Page Glass Insert - Swing Doo
Page 5 and 6: ELECTRICAL REQUIREMENTS There are s
Page 7 and 8: CABINET INSTALLATION AND SET UP CHE
Page 9 and 10: INSTALLATION INSTRUCTION GDM / T-Se
Page 11 and 12: This scale may be used as a guide f
Page 13 and 14: REQUIRED TOOLS • Slotted Screwdri
Page 15 and 16: Notes
Page 17 and 18: CABINET MAINTENANCE SCHEDULE Monthl
Page 21 and 22: POLYOL ESTER LUBRICANT THE CFC REPO
Page 23 and 24: CFC & Refrigeration Basics BASIC RE
Page 25 and 26: TRUE’S REMOTE SYSTEM - HOW IT WOR
Page 29 and 30: TOP REMOVAL FOR TBB & TDD UNITS Dis
Page 31 and 32: TPP COUNTERTOP REPLACEMENT INSTRUCT
Page 33 and 34: 1. Disconnect the power to the unit
Page 35 and 36: INSTALLATION INSTRUCTION END CAP RE
Page 37: The pro c e d u re listed below wil
Page 41 and 42: REQUIRED TOOLS INSTALLATION INSTRUC
Page 43 and 44: INSTALLATION INSTRUCTION TEMPERATUR
Page 49 and 50: REQUIRED TOOLS • Permagum • Phi
Page 51 and 52: SURGE PROTECTOR INSTALLATION This i
Page 57 and 58: REQUIRED TOOLS • Drill • 1/8”
Page 59 and 60: INSTALLATION INSTRUCTION REMOVAL AN
Page 61 and 62: INSTALLATION INSTRUCTION TORSION SP
Page 63 and 64: REQUIRED TOOLS • Phillips Head Sc
Page 65 and 66: INSTALLATION INSTRUCTIONS Glass Ins
Page 67 and 68: REPLACEMENT OF DOOR FRAME HEATER ON
Page 69 and 70: INSTALLATION INSTRUCTION IDL Harnes
Page 71 and 72: INSTALLATION INSTRUCTION SHIMMING T
Page 73 and 74: REQUIRED TOOLS • Drewel tool or s
Page 75 and 76: SLIDE BARREL LOCK (FRONT VIEW) 34 3
Page 79 and 80: REQUIRED TOOLS • Phillips screwdr
Page 81 and 82: KIT CONTENTS • Shelf, 1 ea. • S
Page 83 and 84: This instruction is True’s recomm
Page 87 and 88: KIT CONTENTS • Clear Plastic Shie
Page 89 and 90:
INSTALLATION INSTRUCTION GDM-33CPT
Page 91 and 92:
This instruction is True's recommen
Page 93 and 94:
REQUIRED TOOLS • Drill - 1/4" Bit
Page 95 and 96:
Notes
Page 97 and 98:
REQUIRED TOOLS • Accurate Remote
Page 99 and 100:
A B C D E COMPLAINT CFC & REFRIGERA
Page 101 and 102:
CAPILLARY TUBE REPLACEMENT INSTRUCT
Page 103 and 104:
REFRIGERATION TROUBLESHOOTING CHART
Page 105 and 106:
REFRIGERATION TROUBLESHOOTING CHART
Page 107 and 108:
CAPILLARY TUBE REPLACEMENT INSTRUCT
Page 109 and 110:
FIELD TROUBLESHOOTING 3. Check the
Page 111 and 112:
TROUBLESHOOTING FLUORESCENT LIGHTIN
Page 113 and 114:
Notes
Page 115 and 116:
EQUIPMENT CARE AND CLEANING Cleanin
Page 117 and 118:
STAINLESS STEEL EQUIPMENT CARE AND
Page 119 and 120:
STAINLESS STEEL EQUIPMENT CARE AND
Page 121:
Notes
show all

Technical Service Manual - mbm-Service GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?