WellGate 3804A and WellGate 2540 P2P Hotline application

WellGate 3804A ( 4-FXO ) and WellGate 2540 (4-FXO gateway) in Peerto Peer mode with Hotline by port to port application.Note :Please use Windows XP IE 6.0 web browser or above version to configure bothFXO and FXS gateway webpage setting. Welltech products don’t support otherWeb Browser such as FireFox to configure.Here is a typical diagram of this application at Figure 1.Figure 1Before start to configure of both FXO gateway, we have assigned the followingparameters to both devices as follows. Please note that both IP addresses at FXOgateway’s WAN port should be able to see each other. Both FXO gateway CAN NOTinstall behind Router or Firewall or IP Sharing.WellGate 2540 (4-FXO Gateway ) information :IP address : 192.168.18.30SIP Trunk number : 1005FXO Telephone Number : 1001, 1002, 1003 and 1004WellGate 3804A (4-FXO Gateway ) information :IP address : 192.168.18.220FXO Telephone Number : 2001, 2002, 2003 and 2004

For WellGate 3804A configurationStep 1: Configure static IP address to WellGate 3804A, like below Figure 2.For example: Set static IP address of 192.168.18.220 at WAN port on NetworkInterface Network Interface of WellGate 3804A WEB page.Figure 2Step 2: Set SIP information on SIP Config.Selected Mode to Proxy after enters Primary Proxy IP Address and port. (Seefigure 3).The Proxy IP address and port needs to set WG2540’s IP address and portFor example: there IP Address and port is 192.168.18.30 and 8080.Enter the line 1 to line 4 numbers.For example: There are 2001 to 2004.Press OK button.

Figure 3Step 3: Set Hotline numbers for line 1 to line 4. (see figure 4)For example: there are set WG2540’s line 1 to line 4 numbers for 1001 to1004.Press OK button.Figure 4Step 4: Set RTP Payload Type to 101 or to match as WG2540’s payload type.(See figure 5)

Figure 5WellGate 2540 (FXO Gateway) configurationStep 1: set static IP address to WellGate 2540 FXO gateway’s WAN port as followingpicture. For example: Set static IP address 192.168.18.30 on Device SettingNetwork of WellGate 2540 WEB page. (See Figure 6)Figure 6Step 2: Set the FXO SIP line’s information to each line.Go to FXO Setting webpage of WellGate 2540 FXO Gateway and configure eachline by selecting Line ID from 1 to 4. See Figure 7 and Figure 8. Enable Hotlinefeature by selecting Incoming Call Handling to Hot Line and give remote WellGate

3804A FXO gateway port 1 number to 2001. Enter the numbers of TEL No 1001 to1004 from port 1 to port 4.For example:WG2540 port 1 number 1001 hotline to remote WG3804A port 1 number 2001directly.WG2540 port 2 number 1002 hotline to remote WG3804A port 2 number 2002directly.WG2540 port 3 number 1003 hotline to remote WG3804A port 3 number 2003directly.WG2540 port 4 number 1004 hotline to remote WG3804A port 4 number 2004directly.Figure 7Figure 8

Step 3: Set the SIP Trunk information to WellGate 2540 by going to SIP Trunk Modify SIP Trunk webpage. See Figure 91. Select Register Type to predefine and key in the Proxy Server IP address at192.168.18.220 and port 5060 which are remote WG3804A Gateway’s IPaddress and SIP port number.2. Next, configure a SIP Trunk number, user ID, password and display name to SIPTrunk as following examples. See Figure 10.Enter SIP Trunk #1 information as follows.TEL No : 1005User ID : 1005User password: 1005Display Name: 1005Figure 9Figure 10