Serverview Trap List
Serverview Trap List Serverview Trap List
18 B Trap List TRAP-TYPE/ Alarm type fanCriticalError Fan will fail cabinetNotConfigured Cabinet not configured powerSupplyRemoved Power supply removed powerSupplyAdded Power supply added powerSupplyFailed Power supply failed powerSupplyOk Power supply OK powerSupplyStatusCritical Power supply critical fanOk Fan OK tempSensorBroken Temperature sensor broken serverManagementDisabled Server management disabled table: SNI-SERVER-CONTROL-MIB Trap (ENTERPRISE : enterprises.231.2.10.2) Specific Level of importance 622 MAJOR Fan %d will fail in near future in cabinet %d of server %s. 623 INFORMAT IONAL 624 INFORMAT IONAL 625 INFORMAT IONAL Cabinet %d at server %s is not configured. Depending on the system type, run Server Configuration Utility (SCU) or Storage Extension Manager (SEMAN) and configure the cabinet! Power supply %d in cabinet %d at server %s was removed. Power supply %d in cabinet %d at server %s was added. 626 MAJOR Power supply %d in cabinet %d at server %s failed. 627 INFORMAT IONAL Power supply %d in cabinet %d at server %s is working again. 628 CRITICAL Insufficiant operating power supplies available in cabinet %d at server %s. 629 INFORMAT IONAL Fan %d in cabinet %d of server %s is working again. 630 MAJOR Temperature sensor %d in cabinet %d of server %s is broken or not connected. 631 INFORMAT IONAL Detailed Messages (%d: optional number %s: system variable) Server management BIOS on server %s is disabled. Enable it to have full server management functionality! Remarks This predicts a fan error. A failure will not occur soon. "Contact Information" in "Read me First", and contact your maintenance engineer. The cabinet is not correctly configured. Set again. The power supply unit was removed by the operator. The power supply unit was added by the operator. The PSU has failed. Refer to "Contact Information" in "Read me First", and contact your maintenance engineer. This message appears after the power supply unit has been attached. Install the power supply unit. This message shows that the fan has returned to normal. This message appears when a fan is replaced. Temperature sensor may be faulty. Refer to "Contact Information" in "Read me First", and contact your maintenance engineer. In order to enable the server management, perform settings using the maintenance tools attached to the hardware.
trapAcFail AC failed TRAP-TYPE/ Alarm type trapDuplicateCabinetId Duplicate cabinet ID trapEventLog Error in event log tempSensorOk Temperature sensor OK svCommunicationEstablished Communication established correctableMemErrorAddr Correctable memory error uncorrectableMemErrorAddr Uncorrectable memory error B.3 SNI-SERVER-CONTROL-MIB (sc.mib) table: SNI-SERVER-CONTROL-MIB Trap (ENTERPRISE : enterprises.231.2.10.2) Specific Level of importance 632 CRITICAL AC failure in cabinet %d of server %s. This message is stored when performing UPS scheduled operations. There is no problem in this case. When not performing UPS scheduled operations, there is a possibility of a power supply error. Refer to "Contact Information" in "Read me First", and contact your maintenance engineer. 633 MAJOR Two or more cabinets have the same ID %d on server %s. 634 MAJOR An error was recorded on server %s. See server management event / error log (Recovery) for detailed information. 635 INFORMAT IONAL 636 INFORMAT IONAL 637 INFORMAT IONAL Detailed Messages (%d: optional number %s: system variable) Temperature sensor %d in cabinet %d of server %s is working again. Communication with the Server Management controller in cabinet %d of server %s established again. Correctable memory error at address %d in cabinet %d of server %s. 638 CRITICAL Uncorrectable memory error at address %d in cabinet %d of server %s. Remarks There is an error in the system configuration. Set the configuration again. An error occurred during POST. Refer to the information stored in "Action" and "Error buffer" in ServerView. This message appears when the temperature sensor recovers. This message appears when communication with the Server Management controller has recovered. An SBE (memory single bit error) has occurred. There is no effect because of the existence of ECC memory. An MBE (memory multibit error) has occurred. Refer to "Contact Information" in "Read me First", and contact your maintenance engineer. 19
- Page 1: About this manual A Trap List Overv
- Page 4 and 5: 4 B.37 EM4513-MIB (unicorn-trap.mib
- Page 6 and 7: 6 A Trap List Overview A.3 Screen d
- Page 8 and 9: 8 A Trap List Overview ● MIB file
- Page 10 and 11: 10 B Trap List TRAP-TYPE/ Alarm typ
- Page 12 and 13: 12 B Trap List TRAP-TYPE/ Alarm typ
- Page 14 and 15: 14 B Trap List TRAP-TYPE/ Alarm typ
- Page 16 and 17: 16 B Trap List B.3 SNI-SERVER-CONTR
- Page 20 and 21: 20 B Trap List TRAP-TYPE/ Alarm typ
- Page 22 and 23: 22 B Trap List sniScShutdownCancell
- Page 24 and 25: 24 B Trap List TRAP-TYPE/ Alarm typ
- Page 26 and 27: 26 B Trap List B.5 SNI-HD-MIB (hd.m
- Page 28 and 29: 28 B Trap List TRAP-TYPE/ Alarm typ
- Page 30 and 31: 30 B Trap List TRAP-TYPE/ Alarm typ
- Page 32 and 33: 32 B Trap List B.11 FSC-SERVERCONTR
- Page 34 and 35: 34 B Trap List table: FSC-SERVERCON
- Page 36 and 37: 36 B Trap List TRAP-TYPE/ Alarm typ
- Page 38 and 39: 38 B Trap List TRAP-TYPE/ Alarm typ
- Page 40 and 41: 40 B Trap List TRAP-TYPE/ Alarm typ
- Page 42 and 43: 42 B Trap List TRAP-TYPE/ Alarm typ
- Page 44 and 45: 44 B Trap List TRAP-TYPE/ Alarm typ
- Page 46 and 47: 46 B Trap List TRAP-TYPE/ Alarm typ
- Page 48 and 49: 48 B Trap List TRAP-TYPE/ Alarm typ
- Page 50 and 51: 50 B Trap List TRAP-TYPE/ Alarm typ
- Page 52 and 53: 52 B Trap List B.19 PROMISE-UNIFIED
- Page 54 and 55: 54 B Trap List TRAP-TYPE/ Alarm typ
- Page 56 and 57: 56 B Trap List B.21 UPSMAN (Upsman.
- Page 58 and 59: 58 B Trap List B.23 PowerNet-MIB (p
- Page 60 and 61: 60 B Trap List TRAP-TYPE/ Alarm typ
- Page 62 and 63: 62 B Trap List TRAP-TYPE/ Alarm typ
- Page 64 and 65: 64 B Trap List TRAP-TYPE/ Alarm typ
- Page 66 and 67: 66 B Trap List TRAP-TYPE/ Alarm typ
18<br />
B <strong>Trap</strong> <strong>List</strong><br />
TRAP-TYPE/<br />
Alarm type<br />
fanCriticalError<br />
Fan will fail<br />
cabinetNotConfigured<br />
Cabinet not configured<br />
powerSupplyRemoved<br />
Power supply removed<br />
powerSupplyAdded<br />
Power supply added<br />
powerSupplyFailed<br />
Power supply failed<br />
powerSupplyOk<br />
Power supply OK<br />
powerSupplyStatusCritical<br />
Power supply critical<br />
fanOk<br />
Fan OK<br />
tempSensorBroken<br />
Temperature sensor broken<br />
serverManagementDisabled<br />
Server management disabled<br />
table: SNI-SERVER-CONTROL-MIB <strong>Trap</strong> (ENTERPRISE : enterprises.231.2.10.2)<br />
Specific<br />
Level of<br />
importance<br />
622 MAJOR Fan %d will fail in near future in cabinet<br />
%d of server %s.<br />
623 INFORMAT<br />
IONAL<br />
624 INFORMAT<br />
IONAL<br />
625 INFORMAT<br />
IONAL<br />
Cabinet %d at server %s is not<br />
configured. Depending on the system<br />
type, run Server Configuration Utility<br />
(SCU) or Storage Extension Manager<br />
(SEMAN) and configure the cabinet!<br />
Power supply %d in cabinet %d at server<br />
%s was removed.<br />
Power supply %d in cabinet %d at server<br />
%s was added.<br />
626 MAJOR Power supply %d in cabinet %d at server<br />
%s failed.<br />
627 INFORMAT<br />
IONAL<br />
Power supply %d in cabinet %d at server<br />
%s is working again.<br />
628 CRITICAL Insufficiant operating power supplies<br />
available in cabinet %d at server %s.<br />
629 INFORMAT<br />
IONAL<br />
Fan %d in cabinet %d of server %s is<br />
working again.<br />
630 MAJOR Temperature sensor %d in cabinet %d of<br />
server %s is broken or not connected.<br />
631 INFORMAT<br />
IONAL<br />
Detailed Messages<br />
(%d: optional number %s: system<br />
variable)<br />
Server management BIOS on server %s<br />
is disabled. Enable it to have full server<br />
management functionality!<br />
Remarks<br />
This predicts a fan<br />
error. A failure will<br />
not occur soon.<br />
"Contact<br />
Information" in<br />
"Read me First", and<br />
contact your<br />
maintenance<br />
engineer.<br />
The cabinet is not<br />
correctly configured.<br />
Set again.<br />
The power supply<br />
unit was removed by<br />
the operator.<br />
The power supply<br />
unit was added by the<br />
operator.<br />
The PSU has failed.<br />
Refer to "Contact<br />
Information" in<br />
"Read me First", and<br />
contact your<br />
maintenance<br />
engineer.<br />
This message appears<br />
after the power<br />
supply unit has been<br />
attached.<br />
Install the power<br />
supply unit.<br />
This message shows<br />
that the fan has<br />
returned to normal.<br />
This message appears<br />
when a fan is<br />
replaced.<br />
Temperature sensor<br />
may be faulty.<br />
Refer to "Contact<br />
Information" in<br />
"Read me First", and<br />
contact your<br />
maintenance<br />
engineer.<br />
In order to enable the<br />
server management,<br />
perform settings<br />
using the<br />
maintenance tools<br />
attached to the<br />
hardware.
Change language