Digilyzer DL1 User Manual

More documents

Recommendations

Info

Measurement Functions display mode: Giving a better readability the display mode determines the rapidity of following up the input signal changes. The available modes are: • SLOW 3 seconds averaging • NRM 1 seconds averaging • FAST no averaging If averaging is active, measurements are smoothed in an exponential way (exponential time constant) before being displayed. 44
Level Sweep The Digilyzer supports a RMS based frequency sweep. This function can be applied to measure the frequency response of devices. During a frequency sweep, the Digilyzer records the Level RMS of every input signal, that has a stable frequency and level, provided that the frequency is higher than the one of the previous sample (otherwise the sample will be neglected). Arrow mode Zoom Y-Scale Measurement Functions Fig 5-43, Frequency sweep graph Within a graph every recorded sample is connected by a straight line approximately to the previous / next sample, thus building the displayed curve. In practice the following steps are required / available for the execution of a frequency sweep. • Arm the sweep recording process by moving the cursor to the REC field and pressing the enter key. • The DL1 detects the start tone (315 Hz or 1 kHz) of an external sweep and the recording is automatically started. This status is indicated by the flashing REC field. Alternatively, the sweep recording may be started manually by pressing the enter key with the cursor on the ARM field. Consequently, the DL1 records every incoming signal with a higher frequency than the previous sample. 45 Arrow readout
Page 1 and 2: Digilyzer DL1 User Manual
Page 3 and 4: INdex: 1. In t r o d u c t Io n 4 C
Page 5 and 6: egistration Introduction Register a
Page 7 and 8: Warnings In order to avoid any prob
Page 9 and 10: Functions Overview The Digilyzer fe
Page 11 and 12: • Some functions, e.g. SCOPE, are
Page 13 and 14: Connectors The Digilyzer includes t
Page 15 and 16: 3. FIrsT sTeps This chapter is a qu
Page 17 and 18: 8. Change auto power off time - Mov
Page 19 and 20: Menu Bar The menu bar allows the us
Page 21 and 22: setup screen Basic Operation The se
Page 23 and 24: display Basics Debugging and analyz
Page 25 and 26: Following errors are analyzed/visua
Page 27 and 28: 5. MeAsureMeNT FuNCTIoNs Channel St
Page 29 and 30: Row number Measurement Functions Pa
Page 31 and 32: Consistency Check The consistency c
Page 33 and 34: Bit statistic The bit statistic fun
Page 35 and 36: Logger The event logger records any
Page 37 and 38: Displaying events The display of th
Page 39 and 40: vu+ppM The Digilyzer offers a combi
Page 41 and 42: Level Measurement The Level menu fe
Page 43: Level RMS The analog Level RMS func
Page 47 and 48: THd+N The THD+N function (Total Har
Page 49 and 50: scope The scope shows the waveform
Page 51 and 52: 7. ACCessorIes MiniLINK MiniLINK al
Page 53 and 54: 8. AppeNdIx 1C2f Format The AES3 st
Page 55 and 56: Logger Event Coding The following c
Page 57 and 58: DL1 event Cs WordLeN Cs CHACHB Cs o
Page 59 and 60: Byte Bit Bit-info Digilyzer Explana
Page 61 and 62: Appendix Consumer Format Coding Ove
Page 63 and 64: Appendix Byte Bit Bit-info Digilyze
Page 65 and 66: Dimensions (L x W x H) 163 x 86 x 4

Digilyzer DL1 User Manual

Create successful ePaper yourself

Delete template?

Save as template?