Digilyzer DL1 User Manual

More documents

Recommendations

Info

• Select the REC field, press enter and the RECORD window is displayed. • Select the recording interval of the recording. The max. recording length is defined by this resolution. The <strong>Digilyzer</strong> has the capability to store data of 500 recording intervals. A higher recording interval is causing a shorter maximum recording length. • Select and confirm GO! to start the logger function. The recording setup window disappears and the REC field is flashing. • The logging may be stopped by pressing the enter key at the REC field. Mask frame Sum of event occurances Event list Measurement Functions Sum of all events in event list Fig 5-21, Overview records Display interval: The events occurred during the user defined display interval are summarized and shown on the <strong>Digilyzer</strong>. The bundling of logger data helps to make the events more clear and easy to overview. After the logging is completed the display interval may be changed. • Zoom out the intervals, e.g. the error log has a recording interval of ten seconds and you want to know how many events have been found in the last hour, just zoom out to a display interval of one hour. • Zoom in to get a more detailed information about the time of individual events occurred. • Set to ALL (maximum zoom out) to get an overview of all records. 36 Display interval Event name
Displaying events The display of the event logger is split into three areas: Basic setting Event list Logger info line Measurement Functions Fig 5-22, Detailed info of records Event list: After the cursor is navigated to the event list, it can be scrolled with the up/down key. In this mode the data can be zoomed by using the left and right arrow keys. Press ESC to quit the event list. Logger info line: While the cursor is in the event list, the individual detailed information to the selected event is displayed. Many errors may occur on channel A or B separately (e.g. AU OVERLOAD) and be indicated. 37
Page 1 and 2: Digilyzer DL1 User Manual
Page 3 and 4: INdex: 1. In t r o d u c t Io n 4 C
Page 5 and 6: egistration Introduction Register a
Page 7 and 8: Warnings In order to avoid any prob
Page 9 and 10: Functions Overview The Digilyzer fe
Page 11 and 12: • Some functions, e.g. SCOPE, are
Page 13 and 14: Connectors The Digilyzer includes t
Page 15 and 16: 3. FIrsT sTeps This chapter is a qu
Page 17 and 18: 8. Change auto power off time - Mov
Page 19 and 20: Menu Bar The menu bar allows the us
Page 21 and 22: setup screen Basic Operation The se
Page 23 and 24: display Basics Debugging and analyz
Page 25 and 26: Following errors are analyzed/visua
Page 27 and 28: 5. MeAsureMeNT FuNCTIoNs Channel St
Page 29 and 30: Row number Measurement Functions Pa
Page 31 and 32: Consistency Check The consistency c
Page 33 and 34: Bit statistic The bit statistic fun
Page 35: Logger The event logger records any
Page 39 and 40: vu+ppM The Digilyzer offers a combi
Page 41 and 42: Level Measurement The Level menu fe
Page 43 and 44: Level RMS The analog Level RMS func
Page 45 and 46: Level Sweep The Digilyzer supports
Page 47 and 48: THd+N The THD+N function (Total Har
Page 49 and 50: scope The scope shows the waveform
Page 51 and 52: 7. ACCessorIes MiniLINK MiniLINK al
Page 53 and 54: 8. AppeNdIx 1C2f Format The AES3 st
Page 55 and 56: Logger Event Coding The following c
Page 57 and 58: DL1 event Cs WordLeN Cs CHACHB Cs o
Page 59 and 60: Byte Bit Bit-info Digilyzer Explana
Page 61 and 62: Appendix Consumer Format Coding Ove
Page 63 and 64: Appendix Byte Bit Bit-info Digilyze
Page 65 and 66: Dimensions (L x W x H) 163 x 86 x 4

Digilyzer DL1 User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?