Avalanche User Guide - Wavelink

More documents

Recommendations

Info

Chapter 5: Location Management 502 Select the Properties tab.3 On the Applied Profiles tab, click Edit Exclusions.4 Enable the Excluded check box for the inherited profile you want to exclude.5 Click Save.The profile will be excluded, but will still appear in the Applied Profiles tab for all sublocations.To reapply an inherited profile:1 From the Navigation Window, select the location at which you want to re-apply aninherited profile.2 Select the Properties tab.3 On the Applied Profiles tab, click Edit Exclusions.4 Disable the Excluded check box for the inherited profile you want to reapply.5 Click Save.The profile will be applied for the selected location. It will also be inherited as an appliedprofile, rather than as an excluded profile.
Chapter 6: Managing Network Profiles 51Chapter 6: Managing Network ProfilesA network profile is used to configure devices for your network. The profile containsinformation such as gateway addresses, subnet masks, WWAN settings, and encryption andauthentication information. You can also use a network profile to assign IP addresses to yourdevices. Once the wireless devices are configured with the values from the network profile,you can manage the devices through the Avalanche Console.You can schedule a specific time for a network profile change to take effect. By default,network settings take effect when the profile is enabled. However, you can configure the dateand time for the settings to take effect.The Authorized Users button allows you to assign privileges for a profile to a user that doesnot have rights for that profile. This allows you to give a user permission for one specificprofile, rather than all profiles of a specific type. Users that already have permission for theprofile will not appear in the list of available users. For information about creating users andassigning permissions, see Managing User Accounts on page 35.This section contains the following topics:• Creating Network Profiles• Configuring General Settings for Network Profiles• Configuring Scheduled Settings• Exporting Profiles for Configuring EnablersCreating Network ProfilesA network profile allows you to control network settings for mobile devices. The profile mustbe enabled and applied to a location and then it will be used by all devices meeting the profile'sselection criteria. The home location for the profile is the location you have selected when youcreate the profile.To create a network profile:1 From the Profiles tab, click Add Profile.The Add Profile Wizard appears.2 Select the Network Profile option and click Next.3 Type a Name for the profile and set the status to either Enabled or Disabled. Click Next.4 Use the Selection Criteria Builder to create selection criteria for the profile. Click Next.5 Confirm that the information is correct and click Finish.
Page 1 and 2:
Wavelink Avalanche Site EditionJava
Page 3 and 4:
iiiTable of ContentsChapter 1: Intr
Page 5 and 6:
vChapter 8: Managing a Mobile Devic
Page 7 and 8: viiWeb Viewer Tasks 136The Device T
Page 9 and 10: Chapter 1: Introduction 1Chapter 1:
Page 11 and 12: Chapter 1: Introduction 3• Databa
Page 13 and 14: Chapter 1: Introduction 5• You ha
Page 15 and 16: Chapter 2: Licensing 7When you run
Page 17 and 18: Chapter 2: Licensing 93 Click Activ
Page 19 and 20: Chapter 2: Licensing 11Running the
Page 21 and 22: Chapter 3: Avalanche Java Console 1
Page 43 and 44: Chapter 4: Managing User Accounts 3
Page 53 and 54: Chapter 5: Location Management 45Ch
Page 55 and 56: Chapter 5: Location Management 47
Page 57: Chapter 5: Location Management 496
Page 61 and 62: Chapter 6: Managing Network Profile
Page 69 and 70: Chapter 7: Managing Scan to Configu
Page 75 and 76: Chapter 8: Managing a Mobile Device
Page 85 and 86: Chapter 9: Managing Software Profil
Page 97 and 98: Chapter 10: Managing Mobile Devices
Page 109 and 110:
Chapter 11: Using Remote Control 10
Page 111 and 112:
103Changing the Username and Passwo
Page 113 and 114:
105Debug MailSessionEnables or disa
Page 115 and 116:
107NOTE: If you have some devices t
Page 117 and 118:
109Configuring the Remote Control C
Page 119 and 120:
111PassphraseThe passphrase to use
Page 121 and 122:
113NOTE: Once you have configured t
Page 123 and 124:
115Connecting to Mobile DevicesAfte
Page 125 and 126:
117Standard Viewer TasksThis sectio
Page 127 and 128:
119To create a new folder on the de
Page 129 and 130:
121Device Details dialog box. Click
Page 131 and 132:
123• If you are modifying a Multi
Page 133 and 134:
1253 If you are comparing it to a s
Page 135 and 136:
127To clear the log file:1 Click th
Page 137 and 138:
129Device InfoConfiguring Display a
Page 139 and 140:
131NOTE: You can also configure the
Page 141 and 142:
133The Configuration Data Change di
Page 143 and 144:
135The Configuration Data Change di
Page 145 and 146:
137panels:Device Description PanelT
Page 147 and 148:
139Using the Registry ExplorerFrom
Page 149 and 150:
Chapter 12: Managing Mobile Device
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Chapter 14: Managing Alert Profiles
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Chapter 15: Using Selection Criteri
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Chapter 16: Using the Task Schedule
Page 185 and 186:
Chapter 16: Using the Task Schedule
Page 187 and 188:
SSL Certificates for the Web Consol
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Configuring the Remote Control Serv
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Avalanche Services 197Avalanche Ser
Page 207 and 208:
Port Information 199Port Informatio
Page 209 and 210:
Port Information 201Usage Port Type
Page 211:
Wavelink Contact Information 203Wav
show all

Avalanche User Guide - Wavelink

Create successful ePaper yourself

Delete template?

Save as template?