blackmagic atem 1 m/e production switcher - Imagecraft

More documents

Recommendations

Info

70 Operating Your ATEM Switcher Luma Key Settings Performing an Upstream Luma/Linear Key Since luma and linear keys use the same parameters, they are set up on the software control panel and broadcast panel using a common menu, called the luma key menu. What defines the key as being either luma or linear is in the selection of fill and key sources. In a luma key, fill and key sources are the same. For a linear key, fill and key sources are different. To set up a luma/linear key on upstream keyer 1 on the software control panel: Step 1. Expand the upstream key 1 M/E 1 palette and select luma from the key types bar. Step 2. Select the fill source and key source. If performing a luma key, select the same source for both fill and key. Adjust the key parameters to refine the key. For a description of luma key parameters, refer to the table below. To set up a luma/linear key on upstream keyer 1 on the broadcast panel: Step 1. Press the KEY 1 button in the transition control block to enable the keyer on the preview output. The system control will dynamically navigate to the KEY 1 menu. You can manually navigate to the KEY 1 menu by pressing HOME > EFFECTS KEYS > KEY 1. Step 2. Select the LUMA KEY menu button. Step 3. The destination display will say key1fill. Select the fill source on the select bus. Step 4. Hold down the CUT/FILL button so the destination display says key1 cut and select the key source. If performing a luma key, select the same source for both fill and key. Step 5. Adjust the clip and gain controls to refine the key or press the pre-mult button for pre-multipled keys. The clip and gain controls are not available for pre-multipled keys.
71 Operating Your ATEM Switcher Upstream key luma/linear key parameters: Mask Enables a rectangular mask that can then be adjusted using the top, bottom, left and right parameters. Pre-Mult Identifies the key signal as a pre-multiplied key. Clip The clip level adjusts the threshold at which the key cuts its hole. Decreasing the clip level reveals more of the background. If the background video is completely black then the clip value is too low. Gain The gain adjustment electronically modifies the angle between on and off thereby softening the edges of the key. Adjust the gain value until the edge softness is desirable but the background video luminance or brightness is not affected. Inverse Inverts the key signal. Fly Key Enables/disables DVE effects
Page 1 and 2:
Installation and Operation Manual A
Page 3 and 4:
Contents ATEM Production Switchers
Page 5 and 6:
5 Getting Started Introducing ATEM
Page 7 and 8:
7 Getting Started Another great adv
Page 9 and 10:
9 Getting Started Plugging in Multi
Page 11 and 12:
11 Getting Started Follow install p
Page 13 and 14:
13 Getting Started Set IP Address f
Page 15 and 16:
15 Getting Started Plugging in Came
Page 17 and 18:
17 Getting Started ATEM Setup Utili
Page 19 and 20: 19 Getting Started Change Network S
Page 21 and 22: 21 Getting Started GPI and Tally In
Page 23 and 24: 23 Updating the Software ATEM Setup
Page 25 and 26: 25 Connecting Video Outputs There a
Page 27 and 28: 27 Using ATEM Software Control Inte
Page 29 and 30: 29 Using ATEM Software Control ATEM
Page 31 and 32: 31 Using ATEM Software Control Tran
Page 33 and 34: 33 Using ATEM Software Control Proc
Page 35 and 36: 35 Using ATEM Software Control ATEM
Page 37 and 38: 37 Using ATEM Software Control Set
Page 39 and 40: 39 Using ATEM Software Control Cust
Page 41 and 42: 41 CUT FILL SHIFT PREV TRANS KEY 1
Page 43 and 44: E O 43 CUT FILL SHIFT ON ON ON 1 2
Page 45 and 46: 45 Operating Your ATEM Switcher Int
Page 47 and 48: 47 Operating Your ATEM Switcher Cut
Page 49 and 50: 49 Operating Your ATEM Switcher Aut
Page 51 and 52: 51 Operating Your ATEM Switcher To
Page 53 and 54: 53 Operating Your ATEM Switcher Tra
Page 55 and 56: 55 Operating Your ATEM Switcher Wip
Page 57 and 58: 57 Operating Your ATEM Switcher DVE
Page 61 and 62: 61 Operating Your ATEM Switcher Sha
Page 63 and 64: 63 Operating Your ATEM Switcher Sof
Page 65 and 66: 65 Operating Your ATEM Switcher Man
Page 67 and 68: 67 Operating Your ATEM Switcher Key
Page 69: 69 Operating Your ATEM Switcher Bac
Page 73 and 74: 73 Operating Your ATEM Switcher Chr
Page 75 and 76: 75 Operating Your ATEM Switcher Adj
Page 79 and 80: 79 Operating Your ATEM Switcher Add
Page 81 and 82: 81 Operating Your ATEM Switcher Key
Page 83 and 84: 83 Operating Your ATEM Switcher Usi
Page 85 and 86: 85 Operating Your ATEM Switcher Usi
Page 87 and 88: 87 Operating Your ATEM Switcher Med
Page 89 and 90: 89 Blackmagic Media Express What is
Page 91 and 92: 91 Blackmagic Media Express Media L
Page 93 and 94: 93 Blackmagic Media Express Media L
Page 95 and 96: 95 Blackmagic Media Express In the
Page 97 and 98: 97 Blackmagic UltraScope What is Bl
Page 99 and 100: 99 Blackmagic UltraScope Full Scree
Page 101 and 102: 101 Blackmagic UltraScope Color Cor
Page 103 and 104: 103 Blackmagic UltraScope 3. Vector
Page 105 and 106: 105 Blackmagic UltraScope From the
Page 107 and 108: 107 Blackmagic UltraScope 6. Audio
Page 109 and 110: 109 Help Getting Help The fastest w
Page 111 and 112: 111 Help Which notebooks can I use
show all

blackmagic atem 1 m/e production switcher - Imagecraft

Create successful ePaper yourself

Delete template?

Save as template?