MW8CX/MW10C Owner's Manual

More documents

Recommendations

Info

ReferenceFront & Rear PanelsThe following applies to both the MW8CX and MW10C. In cases where different features need to bedescribed for each model, the MW8CX feature will be described first, followed by the MW10C featurein brackets: MW8CX (MW10C).Channel Control Section12567890ABChannels1 and 2(Monaural)136790ABChannels3/4 and 5/6(Stereo)Channels7/8 (7/8 and 9/10)(Stereo)430AB1 MIC Input Jacks (CHs 1 to 5/6)These are balanced XLR-type microphone input jacks(1:Ground; 2:Hot; 3:Cold).2 LINE Input Jacks (CHs 1, 2)These are balanced TRS phone-jack line inputs (T:Hot;R:Cold; S:Ground).You can connect either balanced or unbalanced phone plugsto these jacks.3 LINE Input Jacks (CHs 3/4 to 7/8 (CHs 3/4 to9/10))These are unbalanced phone-jack stereo line inputs.4 LINE Input Jacks (CH 7/8, (CHs 7/8, 9/10))These are unbalanced stereo RCA pin jacks.NOTEWhere an input channel provides both a MIC inputjack and a LINE input jack, or a LINE input jack andan RCA pin jack, you can use either jack but not bothat the same time. Please connect to only one jack oneach channel.5 INSERT Jacks (CHs 1, 2)Each of these jacks provides an insert point between theequalizer and LEVEL control of the corresponding inputchannel (CHs 1, 2). The INSERT jacks are ideal for connectingdevices such as graphic equalizers, compressors, or noisefilters into the corresponding channels. These are TRS (tip,ring, sleeve) phone jacks that carry both the send and returnsignal (tip = send/out; ring = return/in; sleeve = ground).NOTEPatching external devices via an INSERT jackrequires a special insert cable such as illustratedbelow (insert cable sold separately).To the input jack of theexternal processorCCCTo the INSERT I/O jackTip: OUTMW8CXSleeve (Ground)Ring: INTip: OUTTip: INTo the output jack ofthe external processorCAUTIONThe signal output from the INSERT jacks isreverse-phased. This should not be a problemwhen connecting to an effect unit, but please beaware of the possiblility of phase conflict whenconnecting to other types of device. A reversedphasedsignal may result in degraded soundquality or even complete sound cancellation.16MW8CX/MW10C Owner’s Manual
ReferenceFront & Rear Panels6 GAIN ControlAdjusts the input signal level.To achieve the best balance between S/N ratio and dynamicrange, adjust the level so that the PEAK indicator 9 lightsonly occasionally and briefly on the highest input transients.The -60 to -16 scale is the MIC input adjustment range. The-34 to +10 scale is the LINE input adjustment range.7 Switch (High Pass Filter)This switch toggles the HPF on or off. To turn the HPF on,press the switch in ( ). The HPF cuts frequencies below80 Hz (the HPF does not apply to the line inputs of stereoinput channels 34).8 COMP ControlAdjusts the amount of compression applied to the channel.As the knob is turned to the right the compression ratioincreases while the output gain is automatically adjustedaccordingly. The result is smoother, more even dynamicsbecause louder signals are attenuated while the overall levelis boosted.NOTE Avoid setting the compression too high, as the thehigher average output level that results may lead tofeedback.9 PEAK IndicatorThe peak level of the post-EQ signal is detected, and thePEAK indicator lights red when the level reaches 3 dBbelow clipping. For XLR-equipped stereo input channels (3/4 and 5/6), both the post-EQ and post-mic-amp peak levelsare detected, and the indicator lights red if either of theselevels reaches 3 dB below clipping.0 Equalizer (HIGH, MID, and LOW)This three-band equalizer adjusts the channel’s high, mid,and low frequency bands. CH 7/8 (CHs 7/8, 9/10) have twobands: high and low. Setting the knob to the ▼ position producesa flat response in the corresponding band. Turning theknob to the right boosts the corresponding frequency band,while turning to the left attenuates the band. The followingtable shows the EQ type, frequency, and maximum cut/boostfor each of the three bands.B PAN Control (CHs 1, 2)PAN/BAL Control (CHs 3/4, 5/6)BAL Control (CH 7/8 (CHs 7/8, 9/10)The PAN control determines the stereo positioning of thechannel signal on the Stereo L and R buses.The BAL control knob sets the balance between left andright channels. Signals input to the L input (odd channel) goto the Stereo L bus; signals input to the R input (even channel)go to the Stereo R bus.NOTEOn channels where this knob provides both PAN andBAL control (channels 3/4 and 5/6), the knob operatesas a PAN control when input is received via theMIC jack or L (MONO) input only, and as a BAL controlwhen input is received via both L and R inputs.C LEVEL ControlAdjusts the level of the channel signal. Use these knobs toadjust the balance between the various channels.NOTESet the controls for unused channels all the waydown to minimize noise.Band Type FrequencyHIGH Shelving 10 kHzMID Peaking 2.5 kHzLOW Shelving 100 HzMaximumCut/Boost±15 dBA EFFECT (AUX) ControlAdjusts the level of the signal sent from the channel to theEFFECT (AUX) bus. Note that the signal level sent to thebus is also affected by the LEVEL control C. On stereochannels (CHs 3/4 to 7/8 (CHs 3/4 to 9/10)) the signalsfrom the L (odd) and R (even) channels are mixed andthen sent to the EFFECT (AUX) bus.MW8CX/MW10C Owner’s Manual 17
Page 1 and 2: EnglishOwner’s ManualBedienungsan
Page 3 and 4: PRECAUTIONSPLEASE READ CAREFULLY BE
Page 5 and 6: IntroductionThank you for choosing
Page 7 and 8: Mixer BasicsQuick GuideMixer Basics
Page 9 and 10: Mixer BasicsQuick GuideStep4 Adjust
Page 11 and 12: Mixer BasicsQuick Guide4On a Window
Page 13 and 14: Mixer BasicsQuick Guide4To hear pla
Page 15: ReferenceReferenceSetupSynthesizerP
Page 19 and 20: ReferenceFront & Rear Panels9 RETUR
Page 21 and 22: ReferenceFront & Rear PanelsDigital
Page 23 and 24: ReferenceTroubleshootingThe sound i
Page 25 and 26: ReferenceSpecifications■ Analog I
Page 27 and 28: ReferenceSpecifications■ Block Di
Page 29 and 30: 2. RESTRICTIONS• You may not enga
Page 31 and 32: 2. BESCHRANKUNGEN• Sie dürfen ni
Page 33 and 34: 2. RESTRICTIONS• Vous ne pouvez e
Page 35 and 36: 2. RESTRICCIONES• No puede somete

MW8CX/MW10C Owner's Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?