TruVision DVR 60 User Manual - Interlogix
TruVision DVR 60 User Manual - Interlogix TruVision DVR 60 User Manual - Interlogix
3BChapter 4: Operating instructionsItemDescription14. Tour Enter preprogrammed three-digit code to call up shadow tour.15. Focus + and - Use to control focus of camera lens.16. Playback control Use to control playback (Rewind, Pause, Play, and Fast Forward).17. Search Open the Search menu.18. Replay Replay the selected file from the beginning.19. Eject Eject the CD or DVD disk.20. Archive Press once to enter quick archive mode. Press twice to start archiving.Aim the remote control at the IR receiver located at the front of the unit to testoperation.To connect the remote control to the TVR 60:1. Press the Menu button on the remote control or front panel or right-click themouse and select the Menu button. The main menu screen appears.2. Click the Display icon.3. Click the Monitor tab. The Monitor screen appears.4. Check and remember the DVR device address value. The default value is255. This device address is valid for all IR controls.Note: The device address does not apply to keypads.5. On the remote control press the Device button.6. Enter the device address value. It must be the same as that on the TVR 60.7. Press the ENTER button on the remote or front panel.To place batteries into the IR remote control:1. Remove the battery cover.2. Insert the batteries. Make sure that the positive (+) and negative (−) poles arecorrectly placed.3. Replace the battery cover.Troubleshooting the remote control:If the IR remote control is not functioning properly, perform the following tests:• Check the battery polarity.• Check the remaining charge in the batteries.• Check that the IR remote control sensor is not masked.If the problem still exists, please contact your administrator.28 TruVision DVR 60 User Manual
3BChapter 4: Operating instructionsMain menu overviewThe TVR 60 has an icon-driven menu structure that allows you to configure theunit’s parameters. Figure 11 below shows the TVR 60 main menu screen. Eachcommand icon displays a screen that lets you edit a group of TVR 60 settings.Most screens are available only to system administrators.You must be in live mode to access the main menu.The currently selected command icon is highlighted in green.Figure 11: Main menuTable 6: Description of the menu commands and optionsMain menu command iconDisplayCamerasRecordNetworkAlarmsPTZUserSystemsHelpDescriptionConfigures display settings including dwell time, schedule, language anddisplay formats.Configures camera settings including motion detection, video imageadjustments, camera title, and copy settings to other cameras. SeeConfigures recording settings including recording schedules, record quality,and record mode.Configures standard network settings including IP address, e-mailnotifications, DDNS setup, and advanced network settings.Configures alarm settings including alarm input, relay output, video loss,remote alert, pre-alarm and post-alarm seconds.Configures PTZ settings.Configures users, passwords, and access privileges.Configures system settings including system date and time, audio output,device name, RS-485 settings, RS-232 settings, firmware upgrade, harddrive settings, boot log, and shutdown.Provides reference information to the various toolbars, menus, and keyswithin the interface.TruVision DVR 60 User Manual 29
- Page 6 and 7: ivTruVision DVR 60 User Manual
- Page 8 and 9: 0BChapter 1: Product introductionFe
- Page 10: 0BChapter 1: Product introduction4
- Page 13 and 14: 1BChapter 2: InstallationFigure 1:
- Page 15 and 16: 1BChapter 2: InstallationFigure 2:
- Page 18 and 19: 1BChapter 2: InstallationCameraSwit
- Page 20 and 21: 1BChapter 2: InstallationUse an RS-
- Page 22 and 23: 1BChapter 2: InstallationBracketsTh
- Page 24 and 25: 1BChapter 2: Installation18 TruVisi
- Page 26 and 27: 2BChapter 3: Getting startedAny cha
- Page 28 and 29: 2BChapter 3: Getting startedCheck b
- Page 30 and 31: 3BChapter 4: Operating instructions
- Page 32 and 33: 3BChapter 4: Operating instructions
- Page 36 and 37: 3BChapter 4: Operating instructions
- Page 38 and 39: 3BChapter 4: Operating instructions
- Page 40 and 41: 4BChapter 5: Live modeFigure 13: Di
- Page 42 and 43: 4BChapter 5: Live modeTable 10: Pop
- Page 44 and 45: 4BChapter 5: Live modeItem Name Des
- Page 46 and 47: 5BChapter 6: Configuring the live m
- Page 48 and 49: 5BChapter 6: Configuring the live m
- Page 50 and 51: 5BChapter 6: Configuring the live m
- Page 52 and 53: 5BChapter 6: Configuring the live m
- Page 54 and 55: 6BChapter 7: Controlling a PTZ came
- Page 56 and 57: 6BChapter 7: Controlling a PTZ came
- Page 58 and 59: 6BChapter 7: Controlling a PTZ came
- Page 60 and 61: 6BChapter 7: Controlling a PTZ came
- Page 62 and 63: 7BChapter 8: Playing back a recordi
- Page 64 and 65: 7BChapter 8: Playing back a recordi
- Page 66 and 67: 7BChapter 8: Playing back a recordi
- Page 68 and 69: 7BChapter 8: Playing back a recordi
- Page 70 and 71: 7BChapter 8: Playing back a recordi
- Page 72 and 73: 8BChapter 9: Archiving recorded fil
- Page 74 and 75: 8BChapter 9: Archiving recorded fil
- Page 76 and 77: 8BChapter 9: Archiving recorded fil
- Page 78 and 79: 9BChapter 10: Using the Web browser
- Page 80 and 81: 9BChapter 10: Using the Web browser
- Page 82 and 83: 9BChapter 10: Using the Web browser
3BChapter 4: Operating instructionsItemDescription14. Tour Enter preprogrammed three-digit code to call up shadow tour.15. Focus + and - Use to control focus of camera lens.16. Playback control Use to control playback (Rewind, Pause, Play, and Fast Forward).17. Search Open the Search menu.18. Replay Replay the selected file from the beginning.19. Eject Eject the CD or DVD disk.20. Archive Press once to enter quick archive mode. Press twice to start archiving.Aim the remote control at the IR receiver located at the front of the unit to testoperation.To connect the remote control to the TVR <strong>60</strong>:1. Press the Menu button on the remote control or front panel or right-click themouse and select the Menu button. The main menu screen appears.2. Click the Display icon.3. Click the Monitor tab. The Monitor screen appears.4. Check and remember the <strong>DVR</strong> device address value. The default value is255. This device address is valid for all IR controls.Note: The device address does not apply to keypads.5. On the remote control press the Device button.6. Enter the device address value. It must be the same as that on the TVR <strong>60</strong>.7. Press the ENTER button on the remote or front panel.To place batteries into the IR remote control:1. Remove the battery cover.2. Insert the batteries. Make sure that the positive (+) and negative (−) poles arecorrectly placed.3. Replace the battery cover.Troubleshooting the remote control:If the IR remote control is not functioning properly, perform the following tests:• Check the battery polarity.• Check the remaining charge in the batteries.• Check that the IR remote control sensor is not masked.If the problem still exists, please contact your administrator.28 <strong>TruVision</strong> <strong>DVR</strong> <strong>60</strong> <strong>User</strong> <strong>Manual</strong>