TruVision DVR 60 User Manual - Interlogix
TruVision DVR 60 User Manual - Interlogix TruVision DVR 60 User Manual - Interlogix
2BChapter 3: Getting startedAny changes you make to a setup configuration screen are saved when you exitthe screen and return to the main eZ Setup screen.Note: The TVR 60 firmware supports over 16 languages.Figure 8: Setup Wizard screenTo quickly set up the TVR 60:1. Connect all the devices required to the rear panel of the TVR 60. SeeFigure 1 on page 7.2. Turn on the unit using the power switch on the rear panel. After the boot upscreen, the TVR 60 displays video images on-screen.3. Select the preferred language for the system.4. In the eZ Setup screen, click Next. The User Permission screen appears.5. Administrator configuration:Navigate to the Admin Password edit box and click the edit box with themouse, or press Enter on the front panel or remote control, to display thevirtual keyboard. Enter the default admin password, 1234.Note: You must enter an admin password.Caution: It is strongly recommended that you change the password of theadministrator. Do not leave 1234 as the default password. Write it down in asafe place so that you do not forget it.Click Next. You are then asked if you want to enter the HDD Managementscreen.6. HDD management:Click Enter to open the HDD Management screen and configure your HDDsettings as required.20 TruVision DVR 60 User Manual
2BChapter 3: Getting startedYou can group HDDs and assign cameras to a group. See “Setting HDDgroups” on page 113. You can also set up a drive for redundant recording.See “Setting the HDD to redundancy” on page 115.After setting your HDD settings, click OK and then Next. You are then askedif you want to enter the Record Settings screen.7. Recording configuration:Click Enter to open the Record Settings screen.Under the Recording tab, select a camera and specify the camera settings.Click the Schedule tab.Click Edit.TruVision DVR 60 User Manual 21
- Page 6 and 7: ivTruVision DVR 60 User Manual
- Page 8 and 9: 0BChapter 1: Product introductionFe
- Page 10: 0BChapter 1: Product introduction4
- Page 13 and 14: 1BChapter 2: InstallationFigure 1:
- Page 15 and 16: 1BChapter 2: InstallationFigure 2:
- Page 18 and 19: 1BChapter 2: InstallationCameraSwit
- Page 20 and 21: 1BChapter 2: InstallationUse an RS-
- Page 22 and 23: 1BChapter 2: InstallationBracketsTh
- Page 24 and 25: 1BChapter 2: Installation18 TruVisi
- Page 28 and 29: 2BChapter 3: Getting startedCheck b
- Page 30 and 31: 3BChapter 4: Operating instructions
- Page 32 and 33: 3BChapter 4: Operating instructions
- Page 34 and 35: 3BChapter 4: Operating instructions
- Page 36 and 37: 3BChapter 4: Operating instructions
- Page 38 and 39: 3BChapter 4: Operating instructions
- Page 40 and 41: 4BChapter 5: Live modeFigure 13: Di
- Page 42 and 43: 4BChapter 5: Live modeTable 10: Pop
- Page 44 and 45: 4BChapter 5: Live modeItem Name Des
- Page 46 and 47: 5BChapter 6: Configuring the live m
- Page 48 and 49: 5BChapter 6: Configuring the live m
- Page 50 and 51: 5BChapter 6: Configuring the live m
- Page 52 and 53: 5BChapter 6: Configuring the live m
- Page 54 and 55: 6BChapter 7: Controlling a PTZ came
- Page 56 and 57: 6BChapter 7: Controlling a PTZ came
- Page 58 and 59: 6BChapter 7: Controlling a PTZ came
- Page 60 and 61: 6BChapter 7: Controlling a PTZ came
- Page 62 and 63: 7BChapter 8: Playing back a recordi
- Page 64 and 65: 7BChapter 8: Playing back a recordi
- Page 66 and 67: 7BChapter 8: Playing back a recordi
- Page 68 and 69: 7BChapter 8: Playing back a recordi
- Page 70 and 71: 7BChapter 8: Playing back a recordi
- Page 72 and 73: 8BChapter 9: Archiving recorded fil
- Page 74 and 75: 8BChapter 9: Archiving recorded fil
2BChapter 3: Getting startedYou can group HDDs and assign cameras to a group. See “Setting HDDgroups” on page 113. You can also set up a drive for redundant recording.See “Setting the HDD to redundancy” on page 115.After setting your HDD settings, click OK and then Next. You are then askedif you want to enter the Record Settings screen.7. Recording configuration:Click Enter to open the Record Settings screen.Under the Recording tab, select a camera and specify the camera settings.Click the Schedule tab.Click Edit.<strong>TruVision</strong> <strong>DVR</strong> <strong>60</strong> <strong>User</strong> <strong>Manual</strong> 21