TruVision DVR 60 User Manual - Interlogix
TruVision DVR 60 User Manual - Interlogix TruVision DVR 60 User Manual - Interlogix
13BChapter 14: Camera managementFigure 38: Camera management screenEnabling or disabling analog camerasWhen you turn on the DVR the status of all 16 IP cameras is automatically onand all the cameras are recording, even if there are not 16 analog camerasconnected. You can disable the unused camera links in order to save space onthe hard drive.You may also need to disable analog cameras in order to be able to add more IPcameras to the system. You need to disable one analog camera to add one 4CIFIP camera, and to disable two analog cameras to add one 720p IP camera.To enable or disable analog cameras:1. Enter the Camera Management screen by clicking Camera in the main menu.2. Determine the number of analog cameras to disable.3. Click the Status button to enter the Analog Camera Status menu.4. Clear the check boxes of the cameras you want to disable.5. Click OK to save your settings.A confirmation message appears on the screen prompting you to reboot theDVR. Click Yes to reboot.106 TruVision DVR 60 User Manual
13BChapter 14: Camera managementConfiguring IP camerasUse the Camera Management menu to set up IP cameras. You can also add ordelete IP cameras.Only TruVision IP cameras can be configured from the DVR. The DVR detectsand lists all TruVision IP cameras in the IP Camera Settings screen. By defaultthey all have the same IP address. However, each camera must have a uniqueIP address in order to function correctly.Note: UltraView IP cameras can only be configured using TruVision Navigator.It is recommended to install all the analog cameras first and then the IP camerasso that the camera locations are all grouped together.Add IP cameras individually to the system.To configure IP cameras:1. Enter the Camera Management screen by clicking Camera in the main menu.The list of IP cameras available on the network is displayed.2. Click Setup. The IP Camera Settings screen appears.All TruVision IP cameras connected to the DVR over the same network arelisted (there are no IP cameras installed in the example shown.)3. Connect an IP camera to the network. It may take a minute or more to boot ifyou are using a PoE switch to power the camera.4. Click Refresh.The IP camera is now listed with its parameters including its IP address.5. To change a camera’s default IP address, select the camera by doubleclickingthe IP camera listed. In the screen that appears, enter the camera’sIP address and password. The default password is 1234. Click OK to returnto the Camera Settings screen. The new IP address for the selected camerais shown.6. Select a camera from the list and enter its parameters.Use the IP protocol TruVision H.264 (default is UltraView ENC 10.)TruVision DVR 60 User Manual 107
- Page 62 and 63: 7BChapter 8: Playing back a recordi
- Page 64 and 65: 7BChapter 8: Playing back a recordi
- Page 66 and 67: 7BChapter 8: Playing back a recordi
- Page 68 and 69: 7BChapter 8: Playing back a recordi
- Page 70 and 71: 7BChapter 8: Playing back a recordi
- Page 72 and 73: 8BChapter 9: Archiving recorded fil
- Page 74 and 75: 8BChapter 9: Archiving recorded fil
- Page 76 and 77: 8BChapter 9: Archiving recorded fil
- Page 78 and 79: 9BChapter 10: Using the Web browser
- Page 80 and 81: 9BChapter 10: Using the Web browser
- Page 82 and 83: 9BChapter 10: Using the Web browser
- Page 84 and 85: 9BChapter 10: Using the Web browser
- Page 86 and 87: 10BChapter 11: Configuring recordin
- Page 88 and 89: 10BChapter 11: Configuring recordin
- Page 90 and 91: 10BChapter 11: Configuring recordin
- Page 92 and 93: 10BChapter 11: Configuring recordin
- Page 94 and 95: 11BChapter 12: Configuring alarm se
- Page 96 and 97: 11BChapter 12: Configuring alarm se
- Page 98 and 99: 11BChapter 12: Configuring alarm se
- Page 100 and 101: 11BChapter 12: Configuring alarm se
- Page 102 and 103: 11BChapter 12: Configuring alarm se
- Page 104 and 105: 11BChapter 12: Configuring alarm se
- Page 106 and 107: 12BChapter 13: Configuring network
- Page 108 and 109: 12BChapter 13: Configuring network
- Page 110 and 111: 12BChapter 13: Configuring network
- Page 114 and 115: 13BChapter 14: Camera managementEnt
- Page 116 and 117: 13BChapter 14: Camera management5.
- Page 118 and 119: 13BChapter 14: Camera management112
- Page 120 and 121: 14BChapter 15: HDD managementTo set
- Page 122 and 123: 14BChapter 15: HDD managementChecki
- Page 124 and 125: 14BChapter 15: HDD management118 Tr
- Page 126 and 127: 15BChapter 16: Configuring the DVR
- Page 128 and 129: 15BChapter 16: Configuring the DVR
- Page 130 and 131: 15BChapter 16: Configuring the DVR
- Page 132 and 133: 15BChapter 16: Configuring the DVR
- Page 134 and 135: 15BChapter 16: Configuring the DVR
- Page 136 and 137: 16BAppendix A: TroubleshootingFailu
- Page 138 and 139: 17BAppendix B: SpecificationsLangua
- Page 140 and 141: 17BAppendix B: Specifications134 Tr
- Page 142 and 143: 18BAppendix C: PTZ protocols136 Tru
- Page 144 and 145: 19BAppendix D: PTZ protocolsNavigat
- Page 146 and 147: 20BAppendix E: PTZ protocolsFigure
- Page 148 and 149: 20BAppendix E: PTZ protocolsFigure
- Page 150 and 151: 20BAppendix E: PTZ protocolsTVR 60
- Page 152 and 153: 20BAppendix E: PTZ protocols7. Pres
- Page 154 and 155: 20BAppendix E: PTZ protocols148 Tru
- Page 156 and 157: 21BAppendix F: PTZ protocolsAnalog(
- Page 158 and 159: 21BAppendix F: PTZ protocolsAnalog(
- Page 160 and 161: 22BAppendix G: GlossaryTermPTZUSBDe
13BChapter 14: Camera managementConfiguring IP camerasUse the Camera Management menu to set up IP cameras. You can also add ordelete IP cameras.Only <strong>TruVision</strong> IP cameras can be configured from the <strong>DVR</strong>. The <strong>DVR</strong> detectsand lists all <strong>TruVision</strong> IP cameras in the IP Camera Settings screen. By defaultthey all have the same IP address. However, each camera must have a uniqueIP address in order to function correctly.Note: UltraView IP cameras can only be configured using <strong>TruVision</strong> Navigator.It is recommended to install all the analog cameras first and then the IP camerasso that the camera locations are all grouped together.Add IP cameras individually to the system.To configure IP cameras:1. Enter the Camera Management screen by clicking Camera in the main menu.The list of IP cameras available on the network is displayed.2. Click Setup. The IP Camera Settings screen appears.All <strong>TruVision</strong> IP cameras connected to the <strong>DVR</strong> over the same network arelisted (there are no IP cameras installed in the example shown.)3. Connect an IP camera to the network. It may take a minute or more to boot ifyou are using a PoE switch to power the camera.4. Click Refresh.The IP camera is now listed with its parameters including its IP address.5. To change a camera’s default IP address, select the camera by doubleclickingthe IP camera listed. In the screen that appears, enter the camera’sIP address and password. The default password is 1234. Click OK to returnto the Camera Settings screen. The new IP address for the selected camerais shown.6. Select a camera from the list and enter its parameters.Use the IP protocol <strong>TruVision</strong> H.264 (default is UltraView ENC 10.)<strong>TruVision</strong> <strong>DVR</strong> <strong>60</strong> <strong>User</strong> <strong>Manual</strong> 107