TECHNICAL MANU AL CD 30÷520 06.06 M T E 0 11 2 5 6 ... - Chiller
TECHNICAL MANU AL CD 30÷520 06.06 M T E 0 11 2 5 6 ... - Chiller TECHNICAL MANU AL CD 30÷520 06.06 M T E 0 11 2 5 6 ... - Chiller
CD 30 ÷ 520• One module consists of two units, each unit’s main power should be wired independently andthe detail is shown as follow:The minimal diameter Of wire(mm 2 )Hand switchModelItemsPower(metal tube, vinylite)Power wire(
CD 30 ÷ 52012. Debugging• PreparationAfter cleaning the water system pipeline for several times, ensure the water is clean, thenpump and drain again, and start the pump to ensure the flow and the pressure of inlet and outletpipeline is qualified.Notice: the water pump is under the control of the main unit, so when the water system isrunning, it can make the control circuit of water pump AC contactor electrify by temporarilywiring, thus to make the water pump running.Warning: it is absolutely forbidden to start the pump by the control of main unit before the watersystem has been adjusted well. Please set the address switch on the unit controller according to the rule below.Warning: address switch setting must be done without any electric supply and when the unit iselectrified, setting is absolutely forbidden.29
- Page 1 and 2: R22A I R C O N D I T I O N I N GR40
- Page 3 and 4: CD 30 ÷ 520CONTENTSModular Air-coo
- Page 5 and 6: CD 30 ÷ 520Air-cooled heat-pump mo
- Page 7 and 8: CD 30 ÷ 5203. View (one module 65k
- Page 9 and 10: CD 30 ÷ 5205. SpecificationCooling
- Page 11 and 12: CD 30 ÷ 520CoolingModelCD65 130 19
- Page 13 and 14: CD 30 ÷ 5206.3 Pulse width modulat
- Page 15 and 16: CD 30 ÷ 5207. The capacity control
- Page 17 and 18: CD 30 ÷ 5207.1. Heating and coolin
- Page 19 and 20: CD 30 ÷ 5207.2. Cooling and heatin
- Page 21 and 22: CD 30 ÷ 5207.3 Principle of Digita
- Page 23 and 24: CD 30 ÷ 520 Matched RS485 communic
- Page 25 and 26: CD 30 ÷ 520• Installation founda
- Page 27: CD 30 ÷ 52011. WiringAll wiring in
- Page 31 and 32: CD 30 ÷ 520 Please turn on the mai
- Page 33 and 34: CD 30 ÷ 52013. MaintenanceTo ensur
- Page 35 and 36: CD 30 ÷ 5202) Vacuum refrigerant p
- Page 37 and 38: CD 30 ÷ 52014. Troubles and soluti
- Page 39 and 40: CD 30 ÷ 520Compressor stopby thelo
- Page 41 and 42: CD 30 ÷ 52016. Electric control fi
- Page 43 and 44: 18. Unit electric control & communi
- Page 45 and 46: CD 30 ÷ 520Unit electric controlle
- Page 47 and 48: CD 30 ÷ 520systems. The correspond
- Page 49 and 50: CD 30 ÷ 52016——System A electr
- Page 51 and 52: CD 30 ÷ 5203. Failure & protection
- Page 53 and 54: CD 30 ÷ 5202. Pattern& buttons des
- Page 55 and 56: CD 30 ÷ 520number, etc. will be se
- Page 57 and 58: CD 30 ÷ 520H) The current setting
- Page 59 and 60: CD 30 ÷ 5207) Online units & runni
- Page 61 and 62: CD 30 ÷ 5207——Communication wi
- Page 63 and 64: CD 30 ÷ 52063
<strong>CD</strong> 30 ÷ 52012. Debugging• PreparationAfter cleaning the water system pipeline for several times, ensure the water is clean, thenpump and drain again, and start the pump to ensure the flow and the pressure of inlet and outletpipeline is qualified.Notice: the water pump is under the control of the main unit, so when the water system isrunning, it can make the control circuit of water pump AC contactor electrify by temporarilywiring, thus to make the water pump running.Warning: it is absolutely forbidden to start the pump by the control of main unit before the watersystem has been adjusted well. Please set the address switch on the unit controller according to the rule below.Warning: address switch setting must be done without any electric supply and when the unit iselectrified, setting is absolutely forbidden.29