STARCUT 500/730 - Spearhead Machinery Ltd

More documents

Recommendations

Info

Spearhead Star-Cut 500 & 730WALTERSCHEID ManufactureCheck the condition of the friction discs before use and following periods of storage.Release the tension from the spring, turn the clutch while holding the P.T.O to ensurehub is not seized to linings. (SEE BELOW):WarningThe slip clutch is there to protect the gearbox. If theblades strike a large obstacle they may get damaged orbreak - avoid these conditions.TO ENSURE PROPER CLUTCH FUNCTION AFTER LONG PERIODS ON INACTIVITY,FRICTION CLUTCHES SHOULD BE RUN-IN TO PREVENT OXIDATION BUILD UP. THECLUTCHES ARE SET TO THE PROPER TORQUE SETTING FROM THE FACTORY, USINGTHE FOLOWING PROCEDURE WILL PROVIDE THE MOST ACCURATE TORQUE SETTING:1). TIGHTEN THE FOUR NUTS ON THE INNER CIRCLE WITH A 13MM SPANNER. THENUTS SHOULD COMPRESS THE BELLEVILLE SPRING AND RELIEVE THE PRESSURE OFFTHE FRICTION DISCS IN THE CLUTCH.2). ROTATE THE SHAFTS BY ONE REVOLUTION, THIS CAN BE DONE BY RUNNINGTHE MACHINE.3). RETURN THE FOUR NUTS TO THEIR ORIGINAL LOCATION AND ALLOW THECLUTCH TO COOL IF NECESSARY. NOTE: THE THREADS ON THE END OF THE STUDSARE DEFORMED TO PREVENT THE NUTS FROM BEING REMOVED.24
Spearhead Star-Cut 500 & 730EnglishType Position Part No. Newtons Setting (L) Friction disc MachineK90/4T Centre 5770500 1200Nm 18.00mm 4 500/730K90/4T Wing 5770503 1200Nm 21.00mm 4 730K90/4T Outer Wing 5770501 1200Nm 18.00mm 4 500K90/4T Inner Wing 5770502 1600Nm 20.90mm 4 730DanskType Position Reservedel Newtons Indstilling Belaegninger Maskinesnummer.(L)K90/4T Midtersektio 5770500 1200 Nm 18.00mm 4 500/730nK90/4T Inder vinge 5770503 1200 Nm 21.00mm 4 730K90/4T Vinge 5770501 1200 Nm 18.00mm 4 500K90/4T Yder vinge 5770502 1600 Nm 20.90mm 4 730DeutschType Position Teile Newtons Einstellung Reibscheiben Maschinenummer.(L)K90/4T Mitte 5770500 1200 Nm 18.00mm 4 500/730K90/4T Innen 5770503 1200 Nm 21.00mm 4 730FlugelK90/4T Flugel 5770501 1200 Nm 18.00mm 4 500K90/4T AußenFlugel5770502 1600 Nm 20.90mm 4 73025
Page 1 and 2: Spearhead Star-Cut 500 & 730STARCUT
Page 3 and 4: Spearhead Star-Cut 500 & 730Content
Page 5 and 6: Spearhead Star-Cut 500 & 730Recomme
Page 7 and 8: Spearhead Star-Cut 500 & 730Introdu
Page 9 and 10: Spearhead Star-Cut 500 & 730Attachi
Page 11 and 12: Spearhead Star-Cut 500 & 730Setting
Page 13 and 14: Spearhead Star-Cut 500 & 730Operati
Page 15 and 16: Spearhead Star-Cut 500 & 730Transpo
Page 17 and 18: Spearhead Star-Cut 500 & 730Service
Page 19 and 20: Spearhead Star-Cut 500 & 730Every 8
Page 21 and 22: Spearhead Star-Cut 500 & 730MP6 Bla
Page 23: Spearhead Star-Cut 500 & 730English
Page 27 and 28: Spearhead Star-Cut 500 & 730Storage
Page 29 and 30: Spearhead Star-Cut 500 & 730Spearhe
Page 31 and 32: Spearhead Star-Cut 500 & 73031
Page 33: Spearhead Star-Cut 500 & 730Spearhe

STARCUT 500/730 - Spearhead Machinery Ltd

Create successful ePaper yourself

Delete template?

Save as template?