STARCUT 500/730 - Spearhead Machinery Ltd
STARCUT 500/730 - Spearhead Machinery Ltd STARCUT 500/730 - Spearhead Machinery Ltd
Spearhead Star-Cut 500 & 730Clutch Maintenance & SettingsBondioli ManufactureCheck the condition of the friction discs before use and following periods ofstorage. Release the tension from the spring, turn the clutch while holding theP.T.O stationary. Adjust the spring compression to the original setting.Following seasonal use, unload the spring tension and stone clutch assemblyin a dry place. Check condition of friction linings and reset spring compressionto original height before use.Should the assembly overheat due to frequent or prolonged clutch slipping,dismantle for inspection. The original thickness of the lining is 3.2mm, replacethem when worn to 2.5mm. Clean up all contact surfaces and replace anydamaged components before assembly.WarningThe slip clutch is there to protect the gearbox. If theblades strike a large obstacle they may get damaged orbreak - avoid these conditions.22
Spearhead Star-Cut 500 & 730EnglishType Position Part No. Newtons Setting (H) Friction disc MachineFV 42 Centre 5770225 1200 Nm 18.9 mm 57 71 328 500/730FV 34 Inner Wing 5770230 1200 Nm 17.6 mm 57 71 328 500FV 42 Inner Wing 5770231 1600 Nm 18.5mm 57 71 338 730FV 42 Outer Wing 5770207 1200 Nm 17.8 mm 57 71 328 730DanskType Position Reservedels Newtons Indstilling (H) Belaegninger Maskinenummer.FV 42 Midter sektion 5770225 1200 Nm 18.9 mm 57 71 328 500/730FV 34 Inder vinge 5770230 1200 Nm 17.6 mm 57 71 328 500FV 42 Vinge 5770231 1600 Nm 18.5mm 57 71 338 730FV 42 Yder vinge 5770207 1200 Nm 17.8 mm 57 71 328 730DeutschType Position Teilenummer. Newtons Einstellung (H) Reibscheiben MaschineFV 42 Mitte 5770225 1200 Nm 18.9 mm 57 71 328 500/730FV 34 Innen Flugel 5770230 1200 Nm 17.6 mm 57 71 328 500FV 42 Flugel 5770231 1600 Nm 18.5mm 57 71 338 730FV 42 Außen Flugel 5770207 1200 Nm 17.8 mm 57 71 328 73023
- Page 1 and 2: Spearhead Star-Cut 500 & 730STARCUT
- Page 3 and 4: Spearhead Star-Cut 500 & 730Content
- Page 5 and 6: Spearhead Star-Cut 500 & 730Recomme
- Page 7 and 8: Spearhead Star-Cut 500 & 730Introdu
- Page 9 and 10: Spearhead Star-Cut 500 & 730Attachi
- Page 11 and 12: Spearhead Star-Cut 500 & 730Setting
- Page 13 and 14: Spearhead Star-Cut 500 & 730Operati
- Page 15 and 16: Spearhead Star-Cut 500 & 730Transpo
- Page 17 and 18: Spearhead Star-Cut 500 & 730Service
- Page 19 and 20: Spearhead Star-Cut 500 & 730Every 8
- Page 21: Spearhead Star-Cut 500 & 730MP6 Bla
- Page 25 and 26: Spearhead Star-Cut 500 & 730English
- Page 27 and 28: Spearhead Star-Cut 500 & 730Storage
- Page 29 and 30: Spearhead Star-Cut 500 & 730Spearhe
- Page 31 and 32: Spearhead Star-Cut 500 & 73031
- Page 33: Spearhead Star-Cut 500 & 730Spearhe
<strong>Spearhead</strong> Star-Cut <strong>500</strong> & <strong>730</strong>Clutch Maintenance & SettingsBondioli ManufactureCheck the condition of the friction discs before use and following periods ofstorage. Release the tension from the spring, turn the clutch while holding theP.T.O stationary. Adjust the spring compression to the original setting.Following seasonal use, unload the spring tension and stone clutch assemblyin a dry place. Check condition of friction linings and reset spring compressionto original height before use.Should the assembly overheat due to frequent or prolonged clutch slipping,dismantle for inspection. The original thickness of the lining is 3.2mm, replacethem when worn to 2.5mm. Clean up all contact surfaces and replace anydamaged components before assembly.WarningThe slip clutch is there to protect the gearbox. If theblades strike a large obstacle they may get damaged orbreak - avoid these conditions.22