USER MANUAL Dual Ethernet I/O Module Installation and ... - Sixnet
USER MANUAL Dual Ethernet I/O Module Installation and ... - Sixnet USER MANUAL Dual Ethernet I/O Module Installation and ... - Sixnet
TABLE D Modules8AO20M16AI20M16AI8AOAnalog Output and Combination Analog Input and Output modules.Note: Assignments are a template showing 16 analog input and 16 analog output channels. Fewerchannels may be present on the specific module being installed.Upper RowLower RowTerm # Function Term # Function11 AX0 – AI Channel 1 12 AX1– AI Channel 213 AX2 – AI Channel 3 14 AX3 – AI Channel 415 AX4 – AI Channel 5 16 AX5 – AI Channel 617 AX6 – AI Channel 7 18 AX7 – AI Channel 819 AX8 – AI Channel 9 20 AX9 – AI Channel 1021 AX10 – AI Channel 11 22 AX11 – AI Channel 1223 AX12 – AI Channel 13 24 AX13 – AI Channel 1425 AX14 – AO Channel 15 26 AX15 – AO Channel 1627 AY0 – AO Channel 1 28 AY1– AO Channel 229 AY2 – AO Channel 3 30 AY3 – AO Channel 431 AY4 – AO Channel 5 32 AY5 – AO Channel 633 AY6 – AO Channel 7 34 AY7 – AO Channel 835 AY8 – AO Channel 9 (future) 36 AY9 – AO Channel 10 (future)37 AY10 – AO Channel 11 (future) 38 AY11 – AO Channel 12 (future)39 AY12 – AO Channel 13 (future) 40 AY13 – AO Channel 14 (future)41 AY14 – AO Channel 15 (future) 42 AY15 – AO Channel 16 (future)43 Unused 44 UnusedTABLE E Modules10RTDUpper RowLower RowTerm # Function Term # Function11 EXC-1 12 EXC-213 SNS-1 (AX0) 14 SNS-2 (AX1)15 RET-1 16 RET-217 EXC-3 18 EXC-419 SNS-3 (AX2) 20 SNS-4 (AX3)21 RTN-3 22 RTN-423 EXC-5 24 EXC-625 SNS-5 (AX4) 26 SNS-6 (AX5)27 RET-5 28 RTN-629 EXC-7 30 EXC-831 SNS-7 (AX6) 32 SNS-8 (AX7)33 RET-7 34 RET-835 EXC-9 36 EXC-1037 SNS-9 (AX8) 38 SNS-10 (AX9)39 RTN-9 40 RTN-1041 Unused 42 Unused43 Unused 44 UnusedEtherTRAK-2 I/O Module User Manual Page 20 of 37 Last Revised: 05-NOV-2010Sixnet Technology Park 331 Ushers Ballston Lake, NY 12019 USA +1-518-877-5173 support@sixnet.com
TABLE F Modules16ISOTC Upper Row Lower RowTerm # Function Term # Function1 Earth 11 AX0 – TC 1 (+)2 PWR GND 12 AX0 – TC 1 (-)3 PWR 13 AX1 – TC 2 (+)4 PWR2 14 AX1 – TC 2 (-)5 PWR OUT+ 15 AX2 – TC 3 (+)6 WATCHDOG 16 AX2 – TC 3 (-)7 RS485 + 17 AX3 – TC 4 (+)8 RS485 - 18 AX3 – TC 4 (-)9 RS485 Term 19 AX4 – TC 5 (+)10 RS485 GND 20 AX4 – TC 5 (-)21 AX5 – TC 6 (+)22 AX5 – TC 6 (-)23 AX6 – TC 7 (+)24 AX6 – TC 7 (-)25 AX7 – TC 8 (+)26 AX7 – TC 8 (-)27 AX8 – TC 9 (+)28 AX8 – TC 9 (-)29 AX9 – TC 10 (+)30 AX9 – TC 10 (-)31 AX10 – TC 11 (+)32 AX10 – TC 11 (-)33 AX11 – TC 12 (+)34 AX11 – TC 12 (-)35 AX12 – TC 13 (+)36 AX12 – TC 13 (-)37 AX13 – TC 14 (+)38 AX13 – TC 14 (-)40 AX14 – TC 15 (+)41 AX14 – TC 15 (-)42 AX15 – TC 16 (+)43 AX15 – TC 16 (-)TPane10 - 30 VDCUser+-ToRS48DeviceGNDNote – The screw terminals used on the E2-BASE-TC-1(used in E2-16ISOTC-D only) can accept30 to 16 AWG. The screw size is M2 and the recommended torque is 1.5 IN/LB.EtherTRAK-2 I/O Module User Manual Page 21 of 37 Last Revised: 05-NOV-2010Sixnet Technology Park 331 Ushers Ballston Lake, NY 12019 USA +1-518-877-5173 support@sixnet.com
- Page 1 and 2: USER MANUALEtherTRAK ® -2 and Ethe
- Page 3 and 4: Section 1OverviewGeneralSpecificati
- Page 5 and 6: USB installationInstructionsTo use
- Page 7 and 8: Section 2PanelAssemblyAssembly and
- Page 9 and 10: Section 3Setting theNetworkJumperJu
- Page 11 and 12: NOTE:The DI COM jumper is located o
- Page 13 and 14: Section 4PowerRequirementsPower Wir
- Page 15 and 16: Base Power &CommunicationsWiring Di
- Page 17 and 18: Screw Terminals (11 - 44) for Speci
- Page 19: TABLE BModules32DI2432DO2432AI2032A
- Page 23 and 24: Table H Module16DORLYUpper RowLower
- Page 25 and 26: Discrete InputCounter FeatureApplic
- Page 27 and 28: Applicable to:E2-MIX24880E2-MIX2488
- Page 29 and 30: Section 7Dual EthernetModeConfigura
- Page 31 and 32: RS-485 Modes ofOperationThe EtherTR
- Page 33 and 34: OK LEDIndicationON SolidOFF Complet
- Page 35 and 36: Section 10EtherTRAK-2 Module to Wir
- Page 37: Section 11Service InformationServic
TABLE F <strong>Module</strong>s16ISOTC Upper Row Lower RowTerm # Function Term # Function1 Earth 11 AX0 – TC 1 (+)2 PWR GND 12 AX0 – TC 1 (-)3 PWR 13 AX1 – TC 2 (+)4 PWR2 14 AX1 – TC 2 (-)5 PWR OUT+ 15 AX2 – TC 3 (+)6 WATCHDOG 16 AX2 – TC 3 (-)7 RS485 + 17 AX3 – TC 4 (+)8 RS485 - 18 AX3 – TC 4 (-)9 RS485 Term 19 AX4 – TC 5 (+)10 RS485 GND 20 AX4 – TC 5 (-)21 AX5 – TC 6 (+)22 AX5 – TC 6 (-)23 AX6 – TC 7 (+)24 AX6 – TC 7 (-)25 AX7 – TC 8 (+)26 AX7 – TC 8 (-)27 AX8 – TC 9 (+)28 AX8 – TC 9 (-)29 AX9 – TC 10 (+)30 AX9 – TC 10 (-)31 AX10 – TC 11 (+)32 AX10 – TC 11 (-)33 AX11 – TC 12 (+)34 AX11 – TC 12 (-)35 AX12 – TC 13 (+)36 AX12 – TC 13 (-)37 AX13 – TC 14 (+)38 AX13 – TC 14 (-)40 AX14 – TC 15 (+)41 AX14 – TC 15 (-)42 AX15 – TC 16 (+)43 AX15 – TC 16 (-)TPane10 - 30 VDCUser+-ToRS48DeviceGNDNote – The screw terminals used on the E2-BASE-TC-1(used in E2-16ISOTC-D only) can accept30 to 16 AWG. The screw size is M2 <strong>and</strong> the recommended torque is 1.5 IN/LB.EtherTRAK-2 I/O <strong>Module</strong> User Manual Page 21 of 37 Last Revised: 05-NOV-2010<strong>Sixnet</strong> Technology Park 331 Ushers Ballston Lake, NY 12019 USA +1-518-877-5173 support@sixnet.com
Change language