10-inch Contractor Table Saw - Powermatic

1.0 Warranty and ServicePowermatic warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair,please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday.Warranty PeriodThe general warranty lasts for the time period specified in the literature included with your product or on the officialPowermatic branded website.• Powermatic products carry a limited warranty which varies in duration based upon the product. (See chartbelow)• Accessories carry a limited warranty of one year from the date of receipt.• Consumable items are defined as expendable parts or accessories expected to become inoperable within areasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects.Who is CoveredThis warranty covers only the initial purchaser of the product from the date of delivery.What is CoveredThis warranty covers any defects in workmanship or materials subject to the limitations stated below. This warrantydoes not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear,improper repair, alterations or lack of maintenance.Warranty LimitationsWoodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to aTwo Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.How to Get Technical SupportPlease contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proofof initial purchase when calling. If a product requires further inspection, the Technical Service representative willexplain and assist with any additional action needed. Powermatic has Authorized Service Centers located throughoutthe United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the ServiceCenter Locator on the Powermatic website.More InformationPowermatic is constantly adding new products. For complete, up-to-date product information, check with your localdistributor or visit the Powermatic website.How State Law AppliesThis warranty gives you specific legal rights, subject to applicable state law.Limitations on This WarrantyPOWERMATIC LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACHPRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESSFOR A PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOWLONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.POWERMATIC SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, ORFOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OFOUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL ORCONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.Powermatic sells through distributors only. The specifications listed in Powermatic printed materials and on the officialPowermatic website are given as general information and are not binding. Powermatic reserves the right to effect atany time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deemnecessary for any reason whatsoever.Product Listing with Warranty Period90 Days – Parts; Consumable items1 Year – Motors, Machine Accessories2 Year – Woodworking Machinery used for industrial or commercial purposes5 Year – Woodworking MachineryNOTE: Powermatic is a division of JPW Industries, Inc. References in this document to Powermatic also apply toJPW Industries, Inc., or any of its successors in interest to the Powermatic brand.2

2.0 Table of contentsSection1.0 Warranty and Service ..................................................................................................................................... 22.0 Table of contents ............................................................................................................................................ 33.0 Safety warnings .............................................................................................................................................. 43.1 Kickback ..................................................................................................................................................... 54.0 About this manual .......................................................................................................................................... 65.0 Glossary ......................................................................................................................................................... 76.0 Features ......................................................................................................................................................... 87.0 Specifications ................................................................................................................................................. 88.0 Setup and Assembly .................................................................................................................................... 108.1 Shipping contents ..................................................................................................................................... 108.2 Unpacking and cleanup ............................................................................................................................ 118.3 Stand assembly ........................................................................................................................................ 128.4 Mounting saw to stand ............................................................................................................................. 138.5 Installing handwheels/hooks .................................................................................................................... 138.6 Installing table extensions ........................................................................................................................ 148.7 Leveling table extensions ......................................................................................................................... 148.8 Rails and Fence ....................................................................................................................................... 148.9 Wood Extension Table ............................................................................................................................. 148.10 Switch bracket ........................................................................................................................................ 158.11 Motor cover ............................................................................................................................................ 158.12 Table insert ............................................................................................................................................. 158.13 Installing and removing blade ................................................................................................................. 158.14 Riving knife ............................................................................................................................................. 168.15 Blade guard ............................................................................................................................................ 169.0 Electrical connections .................................................................................................................................. 169.1 Grounding instructions ............................................................................................................................. 169.2 Voltage conversion ................................................................................................................................... 179.3 Extension cords ........................................................................................................................................ 179.4 Switch lockout .......................................................................................................................................... 1810.0 Adjustments ............................................................................................................................................... 1810.1 Fence alignment ..................................................................................................................................... 1810.2 Blade raising/tilt mechanism ................................................................................................................... 1810.3 Miter gauge ............................................................................................................................................ 1810.4 Positive blade stops ............................................................................................................................... 1910.5 Riving knife alignment ............................................................................................................................ 2010.6 Low profile riving knife ............................................................................................................................ 2010.7 Trunnion adjustment ............................................................................................................................... 2010.8 Table to blade alignment ........................................................................................................................ 2010.9 Belt tension and replacement ................................................................................................................. 2111.0 Operations .................................................................................................................................................. 2112.0 Safety devices ............................................................................................................................................ 2613.0 Maintenance ............................................................................................................................................... 2714.0 Optional accessories .................................................................................................................................. 2815.0 Troubleshooting the 64B Table Saw .......................................................................................................... 2916.0 Replacement Parts ..................................................................................................................................... 2916.1.1 Table and Cabinet Assembly – Exploded View ................................................................................... 3016.1.2 Table and Cabinet Assembly – Parts List ........................................................................................... 3116.2.1 Motor and Trunnion Assembly – Exploded View ................................................................................. 3216.2.2 Motor and Trunnion Assembly – Parts List ......................................................................................... 3316.3.1 Stand Assembly – Exploded View ....................................................................................................... 3516.3.2 Stand Assembly – Parts List ............................................................................................................... 3516.4.1 Blade Guard and Miter Gauge Assemblies – Exploded View ............................................................. 3616.4.2 Blade Guard and Miter Gauge Assemblies – Parts List ...................................................................... 3717.0 Electrical Connections ................................................................................................................................ 3817.1 Connections for 115 volt (64B Table Saw) ............................................................................................ 3817.2 Connections for 230 volt (64B Table Saw) ............................................................................................ 393Page

• Arsenic and chromium from chemicallytreated lumber.3.0 Safety warnings1. Read and understand the entire owner'smanual before attempting assembly oroperation.2. Read and understand the warnings posted onthe machine and in this manual. Failure tocomply with all of these warnings may causeserious injury.3. Replace the warning labels if they becomeobscured or removed.4. This table saw is designed and intended foruse by properly trained and experiencedpersonnel only. If you are not familiar with theproper and safe operation of a table saw, donot use until proper training and knowledgehave been obtained.5. Do not use this table saw for other than itsintended use. If used for other purposes,Powermatic disclaims any real or impliedwarranty and holds itself harmless from anyinjury that may result from that use.6. Always wear approved safety glasses/faceshields while using this table saw. Everydayeyeglasses only have impact resistant lenses;they are not safety glasses.7. Before operating this table saw, remove tie,rings, watches and other jewelry, and rollsleeves up past the elbows. Remove all looseclothing and confine long hair. Non-slipfootwear or anti-skid floor strips arerecommended. Do not wear gloves.8. Always use the blade guard on all ''throughsawing''operations. A through-sawingoperation is one in which the blade cutscompletely through the workpiece.9. Kickback occurs when the workpiece is throwntowards the operator at a high rate of speed. Ifyou do not have a clear understanding ofkickback and how it occurs, DO NOT operatethis table saw!10. Wear ear protectors (plugs or muffs) duringextended periods of operation.11. Some dust created by power sanding, sawing,grinding, drilling and other constructionactivities contain chemicals known to causecancer, birth defects or other reproductiveharm. Some examples of these chemicals are:• Lead from lead based paint.• Crystalline silica from bricks, cement andother masonry products.Your risk of exposure varies, depending onhow often you do this type of work. To reduceyour exposure to these chemicals, work in awell-ventilated area and work with approvedsafety equipment, such as face or dust masksthat are specifically designed to filter outmicroscopic particles.12. Do not operate this machine while tired orunder the influence of drugs, alcohol or anymedication.13. Make certain switch is in the OFF positionbefore connecting machine to power supply.14. Make certain the machine is properlygrounded.15. Make all machine adjustments or maintenancewith the machine unplugged from the powersource.16. Remove adjusting keys and wrenches. Form ahabit of checking to see that keys andadjusting wrenches are removed from themachine before turning it on.17. Keep safety guards in place at all times whenthe machine is in use. If removed formaintenance purposes, use extreme cautionand replace the guards immediately aftercompletion of maintenance.18. Check damaged parts. Before further use ofthe machine, a guard or other part that isdamaged should be carefully checked todetermine that it will operate properly andperform its intended function. Check foralignment of moving parts, binding of movingparts, breakage of parts, mounting and anyother conditions that may affect its operation.A guard or other part that is damaged shouldbe properly repaired or replaced.19. Provide for adequate space surrounding workarea and non-glare, overhead lighting.20. Keep the floor around the machine clean andfree of scrap material, oil and grease.21. Keep visitors a safe distance from the workarea. Keep children away.22. Make your workshop child proof with padlocks,master switches or by removing starter keys.23. Give your work undivided attention. Lookingaround, carrying on a conversation and “horseplay”are careless acts that can result inserious injury.24. Maintain a balanced stance at all times so thatyou do not fall into the blade or other movingparts. Do not overreach or use excessive forceto perform any machine operation.

25. Use the right tool at the correct speed andfeed rate. Do not force a tool or attachment todo a job for which it was not designed. Theright tool will do the job better and more safely.26. Use recommended accessories; improperaccessories may be hazardous.27. Maintain tools with care. Keep saw bladessharp and clean for the best and safestperformance. Follow instructions for lubricatingand changing accessories.28. Turn off the machine before cleaning. Use abrush or compressed air to remove chips ordebris — do not use your hands.29. Do not stand on the machine. Serious injurycould occur if the machine tips over.30. Never leave the machine running unattended.Turn the power off and do not leave themachine until it comes to a complete stop.31. Remove loose items and unnecessary workpieces from the area before starting themachine.32. Keep hands out of the line of saw blade.33. Use a push-stick when required.34. Pay particular attention to instructions onreducing risk of kickback.35. Do not perform any operation freehand.36. Never reach around or over saw blade.37. Don’t use in dangerous environment. Don’tuse power tools in damp or wet location, orexpose them to rain. Keep work area welllighted.3.1 KickbackThe most common accidents among table sawusers, according to statistics, can be linked tokickback, the high-speed expulsion of material fromthe table that can strike the operator. Kickback canalso result in the operator’s hands being pulled intothe blade.Kickback PreventionTips to avoid the most common causes ofkickback:• Make sure the riving knife is always alignedwith the blade. A workpiece can bind or stopthe flow of the cut if the riving knife ismisaligned, and result in kickback.• Use a riving knife during every cut. The rivingknife maintains the kerf in the workpiece,which will reduce the chance of kickback.• Never attempt freehand cuts. The workpiecemust be fed parallel to the blade, otherwisekickback will likely occur. Always use the ripfence or miter gauge to support the workpiece.• Make sure that rip fence is parallel to blade. Ifnot, the chances of kickback are very high.Take the time to check and adjust the ripfence.• Feed cuts through to completion. Anytime youstop feeding a workpiece that is in the middleof a cut, the chance of binding, resulting inkickback, is greatly increased.Protection Tips from KickbackKickback can happen even if precautions are takento prevent it. Listed below are some tips to protectyou if kickback does occur:• Stand to the side of the blade when cutting. Anejected workpiece usually travels directly infront of the blade.• Wear safety glasses or a face shield. Youreyes and face are the most vulnerable part ofyour body.• Never place your hand behind the blade. Ifkickback occurs, your hand will be pulled intothe blade.• Use a push stick to keep your hands fartheraway from the moving blade. If a kickbackoccurs, the push stick will most likely take thedamage that your hand would have received.5

Familiarize yourself with the following safety notices used in this manual:This means that if precautions are not heeded, it may result in minor injury and/or possiblemachine damage.death.This means that if precautions are not heeded, it may result in serious injury or possibly even4.0 About this manualThis manual is provided by Powermatic covering the safe operation and maintenance procedures for aPowermatic Model 64B Contractor Table Saw. This manual contains instructions on installation, safetyprecautions, general operating procedures, maintenance instructions and parts breakdown. Your machine hasbeen designed and constructed to provide years of trouble-free operation if used in accordance with theinstructions as set forth in this document.This manual is not intended to be an exhaustive guide to table saw operational methods, use of jigs or aftermarketaccessories, choice of stock, etc. Additional knowledge can be obtained from experienced users ortrade articles. Whatever accepted methods are used, always make personal safety a priority.If there are questions or comments, please contact your local supplier or Powermatic. Powermatic can also bereached at our web site: www.powermatic.com.Retain this manual for future reference. If the machine transfers ownership, the manual should accompany it.Read and understand the entire contents of this manual before attempting assemblyor operation. Failure to comply may cause serious injury.6

5.0 GlossaryArbor: Metal shaft that connects the drivemechanism to the blade.Bevel Edge Cut: Tilt of the saw arbor and bladebetween 0° and 45° to perform an angled cuttingoperation.Blade Guard: Mechanism mounted over the sawblade to prevent accidental contact with the cuttingedge.Crosscut: Sawing operation in which the mitergauge is used to cut across the grain of theworkpiece.Dado Blade: Blade used for cutting grooves andrabbets. A stacked dado set can be used for widergrooves.Dado Cut: Flat bottomed groove in the face of theworkpiece made with a dado blade.Featherboard: Device used to keep a boardagainst the rip fence or table that allows theoperator to keep hands away from saw blade.Freehand: Moving a workpiece into the bladeusing only the hands, without a fixed positioningdevice. (This is a dangerous, unacceptableprocedure – always use appropriate devices tofeed the workpiece though the saw blade duringcutting operations.)Kerf: The resulting cut or gap made by a sawblade.Kerf, Standard: 1/8" gap made with a standardblade.Kickback: An event in which the workpiece is liftedup and thrown back toward the operator, causedwhen a workpiece binds on the saw blade orbetween the blade and rip fence (or other fixedobject). To minimize or prevent injury fromkickbacks, see the Operations section.Miter Gauge: A component that controls theworkpiece movement while performing a crosscutof various angles.Non-Through Cut: A sawing operation thatrequires the removal of the blade guard andstandard riving knife, resulting in a cut that doesnot protrude through the top of the workpiece(includes Dado and rabbet cuts).The blade guard and riving knife must be reinstalledafter performing a non-through cut toavoid accidental contact with the saw blade duringoperation.Parallel: Two lines or surfaces lying at equaldistance from each other at every point along theirlengths. For example, a rip fence must be parallelto the side face of the saw blade.Pawls, Anti-Kickback: Plates with a serratededge, usually mounted to the splitter, that preventthe cut workpiece being drawn back toward theblade and producing kickback.Perpendicular: 90° (right angle) intersection orposition of the vertical and horizontal planes suchas the position of the saw blade (vertical) to thetable surface (horizontal).Push Board/Push Stick: An instrument used tosafely push the workpiece through the cuttingoperation.Rabbet: A cutting operation that creates anL-shaped channel along the edge of the board.Resaw: Process of cutting a thick workpiece intothinner pieces.Rip Cut: A cut made along the grain of theworkpiece.Riving Knife: A metal plate fixed relative to theblade, which moves with the blade as cutting depthis adjusted. Thus, it maintains not only the kerfopening in the workpiece, but also the knife-tobladedistance. A low-profile riving knife sits lowerthan the top edge of the blade, and is used for nonthroughcuts.Splitter (Spreader): A stationary metal plate towhich the blade guard is attached that maintainsthe kerf opening in the workpiece when performinga cutting operation. A splitter that rises and lowerswith the blade is called a riving knife.Straightedge: A tool used to check that a surfaceis flat or parallel.Through Sawing: A sawing operation in which theworkpiece thickness is completely sawn through.Proper blade height usually allows 1/8" of the topof blade to extend above the wood stock. Keep theblade guard down, the anti-kickback pawls down,and the riving knife in place over the blade.7

6.0 FeaturesFigure 11 – Cast iron table extensions2 – T-slots3 – Transparent blade guard with riving knife4 – Precision miter gauge with extension face5 – Accu-Fence ®6 – Rail set (30” shown)7 – Blade tilt handwheel (with lock knob)8 – Blade tilt angle scale9 – Accu-Fence storage hook10 – Adjustable foot pads11 – Blade elevation handwheel (with lock knob)12 – Miter gauge storage hook13 – Industrial style push button switch14 – Motor cover7.0 SpecificationsModel number .................................................................................................................................................... 64BStock Numbers:Model 64B basic saw – with stand, no fence or rails ................................................................................. 1791229Model 64B basic saw – with 30” Rail Set, Accu-Fence ® , 27”x17” Wood Extension Table .........................1791229KModel 64B basic saw – with 50” Rail Set, Accu-Fence ® , 27”x36” Wood Extension Table, Legs ................1791230KMaterials:Stand ............................................................................................................................................................. steelSaw body ....................................................................................................................................................... steelTables........................................................................................................................................... ground cast ironHandwheels ............................................................................................................................................. cast ironTrunnion .................................................................................................................................................. cast ironFence body ................................................................................................................. steel with HDPE side plates8

Motor and Electricals:Motor type .............................................................................. totally enclosed fan cooled, induction, capacitor startHorsepower ............................................................................................................................... 1-3/4 HP (1.3 kW)Phase .......................................................................................................................................................... singleVoltage ......................................................................................................................... 115/230V (prewired 115V)Cycle ........................................................................................................................................................... 60 HzMotor speed .......................................................................................................................................... 3450 RPMListed FLA (full load amps) ....................................................................................................................... 15/7.5 AStarting amps .................................................................................................................................................. 52ARunning amps (no load) .................................................................................................................................... 6AStart capacitor ............................................................................................................................ 400MFD 125VACRun capacitor ....................................................................................................................................... 30μF 250VPower transfer ............................................................................................................................................... v-beltOn/off switch ........................................................................................... manual industrial-style, with padlock holePower cord length .............................................................................................................................. 7 ft. (213cm)Power plug installed ......................................................................................................................................... yesRecommended circuit size 1 ................................................................................... 30A (for 115V) or 20A (for 230V)Noise emission:Without load ........................................................................................................ 78 dB at 20 inches from bladeWith load ............................................................................................................. 85 dB at 20 inches from bladeArbor and blade:Blade Diameter 2 (in.) ..........................................................................................................................10” (254mm)Arbor Diameter (in.) .............................................................................................................................5/8” (16mm)Arbor speed .......................................................................................................................................... 3800 RPMArbor lock ........................................................................................................................................................ yesMaximum cut depth at 90 degrees ................................................................................................... 3-1/8” (79mm)Maximum cut depth at 45 degrees ................................................................................................... 2-1/8” (54mm)Maximum rip to right of blade ................................................................................... 30” (762mm) or 50” (1270mm)Maximum rip to left of blade ................................................................................................................12” (305mm)Dado maximum width .................................................................................................................... 13/16” (20.7mmDado maximum diameter ..................................................................................................................... 8” (200mm)Blade height per one revolution of handwheel .......................................... 5/32” (4mm) for 90°; 1/8” (2.9mm) for 45°Blade tilt .............................................................................................................................................. left, 0 to 45°Table:Table working surface ......................................................................................... 20-1/8” L x 27” W (511 x 686mm)Table working surface, with extensions .............................................................. 44-1/4” L x 27” W (1124 x 686mm)Table working surface, with extensions and optional wood table:With 30” rip capacity ..................................................................................... 71-1/4” L x 27” W (1810 x 686mm)With 50” rip capacity ..................................................................................... 79-5/8” L x 27” W (2022 x 686mm)Table area in front of blade at maximum height ............................................................................. 11-1/2” (292mm)Table height from floor ........................................................................................................................36” (914mm)Miter slot .................................................................................................. two T-slots, 3/4" W x 3/8” D (19 x 10mm)Edge bevel ..................................................................................................................................................... frontDust collection:Dust port outside diameter ................................................................................................................... 4” (100mm)Minimum extraction volume required .......................................................................................... 350 cfm (9.9 cmm)Other:Stand style .....................................................................................................................................................openStand footprint ........................................................................................................ 21-1/2”L x24”W (546 x 610mm)Overall Dimensions, shipping carton (basic saw only) .......................... 39” L x 25” W x 22” H (98.6 x 63.6 x 56.4cm)Overall Dimensions, fully assembled, accessories mounted:With 30” rip capacity ................................................................... 71-1/4” L x 43” W x 42” H (181 x 109 x 107cm)With 50” rip capacity ................................................................... 79-5/8” L x 43” W x 42” H (202 x 109 x 107cm)Weights:Net................................................................................................................................................. 293 lb (133 kg)Shipping......................................................................................................................................... 304 lb (138 kg)1 subject to local and national electrical codes.2 blade not included.9

8.0 Setup and Assembly8.1 Shipping contents(Figures 2 through 7)1 Saw body with switch – A2 Cast iron table extensions – B1 Motor cover – C2 Handwheels – D2 Handwheel locking knobs – E2 Handles – F1 Arbor wrench – G2 Open end wrenches (14-17, 10-12mm) – H4 Hex keys (2.5/3/4/6mm) – I1 Blade guard with anti-kickback pawls – J1 Riving knife – K1 Low profile riving knife – L1 Miter gauge – M1 Push stick – N1 Table insert – OFigure 21 Hardware package (p/n 64B-HP):6 Hex cap screws M10x30 – HP-16 Lock washers 10mm – HP-26 Flat washers 10mm – HP-31 Stand assembly:1 Upper brace, with cutout – P1 Upper brace, long – Q2 Upper braces, short – R2 Lower braces, long – S2 Lower braces, short – T4 Legs – U4 Foot pads – V2 Fence hooks – W1 Miter gauge hook – X1 Small hook – Y1 Stand hardware package (p/n 64B-SHP)4 Hex cap screws M8x25 – SHP-18 Pan head screws M5x15 – SHP-224 Carriage bolts M8x16 – SHP-340 Flat washers 8mm – SHP-428 Lock washers 8mm – SHP-536 Hex nuts M8– SHP-68 Hex nuts M5 – SHP-7Figure 3Figure 4 – Hardware package (64B-HP)1 Instructions and Parts Manual1 Warranty CardNOTE: The Accu-Fence, rail set, optional woodextension table and legs, are all packagedseparately and supplied with their own hardware.Figure 5 – Stand assembly10

Figure 6Figure 7 – Stand hardware package (64B-SHP)8.2 Unpacking and cleanupOpen shipping container and check for shippingdamage. Report any damage immediately to yourdistributor and shipping agent. Do not discard anyshipping material until the Table Saw is assembledand running properly.Compare the contents of your container with theprevious list to make sure all parts are intact.Missing parts, if any, should be reported to yourdistributor. Read the instruction manual thoroughlyfor assembly, maintenance and safety instructions.Tools required for assembly (provided):10, 12, 14 and 17 mm wrenchesHex key setArbor wrenchAdditional tools required (not supplied):Cross point screwdriverRubber mallet or dead-blow hammer (or steelhammer over a block of wood)11

8.3 Stand assemblyAssembly tip: A ratchet wrench with sockets andextensions will speed assembly time.1. Assemble stand, using Figure 8 as a guide.Use the provided carriage bolts, flat washerslock washers, and hex nuts (SHP-3/4/5/6).Only make fasteners snug at this time. Theywill be fully tightened later, after stand hassettled under the weight of the saw.2. Note the orientation of the cut-out brace (P) tothe front brace with Powermatic label (R). Thecut-out brace must be to the left, to allowprotrusion of the motor.3. When stand has been assembled, turn it overand install the rubber foot pads (V). (Shouldyou ever need height adjustment on the footpad, loosen the two hex nuts, rotate the pad,then retighten the hex nuts against the metalof the stand.)4. Turn stand right-side up. The fasteners are notfully tight, but they should be snug enough towithstand the weight of the saw. If the standneeds more stability, snug fasteners a littlemore.5. The four large holes on top of the stand shouldbe reasonably aligned through the upperbraces for easy insertion of the screws.Figure 812

Figure 98.4 Mounting saw to standRefer to Figure 9The table saw is heavy! Getpersons to assist you in lifting it. Failure tocomply may result in serious personal injuryand/or damage to the machine.1. Carefully lift table saw out of carton.2. Place table saw atop the stand, orienting themotor in the cut-out of the stand, and aligningthe four holes on its bottom edge with those inthe stand.3. Insert four screws, with flat washers, lockwashers and hex nuts (SHP-1/4/5/6), asshown.4. Securely tighten all four hex nuts (SHP-6),using a 12mm wrench and an additionalwrench to hold the screw steady whiletightening the nut. (NOTE: If you need moreroom to wrench the back screws, followinstructions below for tilting motor out of theway.)5. Finish tightening all fasteners in the stand.8.5 Installing handwheels/hooksRefer to Figure 9.1. Install a handwheel onto the tilting and raisingshafts, as shown. Fit the slot of the handwheelonto the roll pin on the shaft, then secure byscrewing on the locking knob.2. Install a handle onto each handwheel, using a14mm wrench on the flat to tighten it.3. Install hooks (W and X) with two screws andhex nuts (SHP-2/7). Placement is personalpreference, as all legs have holes for them.NOTE: The two larger hooks will be on thesame side, to hold the fence. The smaller hookholds the miter gauge.4. Mount small hook (Y) to the front, to holdadditional accessories such as arbor wrench,push stick, riving knife, etc.5. Tilt arbor using right handwheel, and removeStyrofoam packing from above motor.13

8.6 Installing table extensionsRefer to Figure 10.Figure 101. Attach a table extension to the saw table.Make sure edge bevel on table extensionfaces front, to match that of saw table. Usethree screws, lock washers and flat washers(HP-1/2/3). Lightly snug screws with 17mmwrench.Assembly Tip: If you are doing this without anassistant, lift table extension vertically to thetable edge. Install center screw and washer,and make snug. Then pivot the extensionparallel to saw table to insert the other twoscrews.2. Repeat for opposite table extension. Lightlysnug screws.3. The front edge of table extensions must beflush with front edge of saw table. If needed,tap front edge of extension with a rubbermallet to make flush. See Figure 11.Figure 11Figure 121. Start by tightening the three screws (17mmwrench) under the table extension that secureit to the saw table. Tighten these just enoughto hold the extension in place but looseenough to change the extension height bytapping on it.2. Lay the straight edge (A, Figure 12) across thesaw table and extension, extending it out pastthe edge of the extension as shown.3. Move the straight edge to several places alongthe table extension, as you continue to nudgethe extension level with the saw table. Whenextension is level with saw table, securelytighten each of the three screws.4. Repeat steps 1 through 3 for opposite tableextension.8.8 Rails and FenceWith table extensions properly aligned, the railsand Accu-Fence ® assembly can now be mountedto the saw. Consult the manual, no. M-2195075Z,that accompanies the fence.NOTE: The two tapped holes at the ends of thetable extensions are not used. There may beadditional holes in the table’s edge that are notrequired for this rail installation.8.9 Wood Extension TableFor instructions on mounting the accessory woodextension table, consult your Accu-Fence®manual, document no. M-2195075Z.8.7 Leveling table extensionsRefer to Figure 12.Level table extensions to saw table using a straightedge. A metal straight edge is ideal, though acarefully jointed board may also be used.14

8.10 Switch bracketRefer to Figure 13.Remove existing screw and washers from thefarthest left hole on the guide tube, and use themto secure the control switch to bottom of guidetube, as shown in Figure 13 (10mm wrench).between table and table insert, slightly raise thatarea of the table insert above main table surface.Figure 158.11 Motor coverFigure 13Refer to Figure 14.1. At the motor side, slide the hinge pins of themotor cover down into the cylinders.2. To secure cover, loosen knob (B), and swingcover shut, while pushing in on the side. Theslot (C) should slide beneath the knob.3. Tighten knob (B).8.13 Installing and removing bladeA blade is not provided with the 64B.1. Using front handwheel, raise blade arbor fullyand tighten lock knob.Refer to Figures 16 and 17.2. Remove nut (A) and flange (B), and installblade onto arbor, making sure the teeth pointdownward toward front of saw.3. Install flange (B) and nut (A).4. Rotate arbor until hole (C, Figure 17) alignswith arbor lock pin (D). Push tab (E) to seat pininto hole, and hold to prevent blade rotation.5. Tighten nut (A) with arbor wrench.6. Release arbor lock (E).Figure 148.12 Table insertRefer to Figure 15.Place insert into table opening (the finger hole istoward front of saw). Verify that insert lies flushwith table surface by resting a straight edge acrossit at various points. If insert is not flush along itslength, turn any of six set screws (D) to raise orlower that area of the insert.NOTE: If while lowering blade, the points on theanti-kickback pawls tend to catch in the seamFigure 1615

2. Push guard down so that the pins slide into theslots in the riving knife, then pull guardbackward to seat.3. Secure with top latch (K).4. The transparent guard leaves (L) should dropfreely to the table.5. Lift the latch (J) to free the pawls. Pawls mustbe lowered into operating position before usingthe saw!8.14 Riving knifeFigure 17Refer to Figure 18.The saw is supplied with two riving knives: Oneextends above the blade and accepts the bladeguard; the other is a low-profile knife that actsalone for non-through cutting.To install a riving knife:1. Remove table insert, and raise arbor all theway up.2. Slide prongs of riving knife into slot betweenblock (F, Figure 18) and plate (G), and pushriving knife down as far as it will go.3. Push lever (H) downward, toward blade, untiltight.4. The riving knife must be parallel to saw blade.See section 10.5.8.15 Blade guardFigure 18Refer to Figure 18.1. Lift the anti-kickback pawls (I) and securethem with the latch (J).9.0 Electrical connectionsElectrical connections mustbe made by a qualified electrician incompliance with all relevant codes. Thismachine must be properly grounded to helpprevent electrical shock and possible fatalinjury.The 64B table saw is rated at 115/230V power, andis pre-wired for 115 volt. The table saw comes witha plug designed for use on a circuit with agrounded outlet that looks like the one pictured inA, Figure 19.Before connecting to power source, be sure switchis in off position.It is recommended that the table saw, whenoperated on 115 volt power, be connected to adedicated 30 amp circuit with a 30 amp circuitbreaker or time-delay fuse marked “D”. Whenoperated on 230 volt power, it is recommendedthat the table saw be connected to a dedicated 20amp circuit with a 20 amp circuit breaker or timedelayfuse marked “D”. Local codes takeprecedence over recommendations.9.1 Grounding instructions1. All Grounded, Cord-connected Tools:In the event of a malfunction or breakdown,grounding provides a path of least resistance forelectric current to reduce the risk of electric shock.This tool is equipped with an electric cord havingan equipment-grounding conductor and agrounding plug. The plug must be inserted into amatching outlet that is properly installed andgrounded in accordance with all local codes andordinances.Do not modify the plug provided - if it will not fit theoutlet, have the proper outlet installed by aqualified electrician.Improper connection of the equipment-groundingconductor can result in a risk of electric shock. Theconductor with insulation having an outer surfacethat is green with or without yellow stripes is theequipment-grounding conductor.16

If repair or replacement of the electric cord or plugis necessary, do not connect the equipmentgroundingconductor to a live terminal.Use only 3-wire extension cords that have 3-pronggrounding plugs and 3-pole receptacles that acceptthe tool's plug.Repair or replace damaged or worn cordimmediately.9.2 Voltage conversionIf 230V single phase operation is desired, followthese instructions:1. Disconnect table saw from power source.2. Open the motor junction box, and consult thediagram on the inside of the junction boxcover. Similar diagrams are shown in section17.0.NOTE: In case of discrepancy, the junctionbox label takes precedence.3. The four motor leads are connected for 115Voperation; reconnect these leads for 230Voperation, as shown in the diagrams.Figure 192. Grounded, cord-connected tools intended foruse on a supply circuit having a nominal rating lessthan 150 volts:This tool is intended for use on a circuit that has anoutlet that looks like the one illustrated in A, Figure19. An adapter, shown in B and C, may be used toconnect this plug to a 2-pole receptacle as shownin B if a properly grounded outlet is not available.The temporary adapter should be used only until aproperly grounded outlet can be installed by aqualified electrician. This adapter is not permittedin Canada. The green-colored rigid ear, lug, andthe like, extending from the adapter must beconnected to a permanent ground such as aproperly grounded outlet box.3. Grounded, cord-connected tools intended foruse on a supply circuit having a nominal ratingbetween 150 - 250 volts, inclusive:This tool is intended for use on a circuit that has anoutlet that looks like the one illustrated in D, Figure19. The tool has a grounding plug that looks likethe plug illustrated in D. Make sure the tool isconnected to an outlet having the sameconfiguration as the plug. No adapter is availableor should be used with this tool. If the tool must bereconnected for use on a different type of electriccircuit, the reconnection should be made byqualified service personnel; and after reconnection,the tool should comply with all local codes andordinances.Check with a qualifiedelectrician or service personnel if thegrounding instructions are not completelyunderstood, or if in doubt as to whether thetool is properly grounded. Failure to complymay cause serious or fatal injury.4. The 115 volt attachment plug, supplied withthe saw, must be replaced with a UL/CSAlisted plug suitable for 230 volt operation.Consult an electrician for proper procedures toinstall the plug. The saw must comply with alllocal and national codes after the 230 volt plugis installed.In all cases (115V or 230V) make certain thereceptacle in question is properly grounded. Ifyou are not sure, have a registered electriciancheck the receptacle.9.3 Extension cordsUSE PROPER EXTENSION CORD. Make sureyour extension cord is in good condition. Whenusing an extension cord, be sure to use one heavyenough to carry the current your product will draw.An undersized cord will cause a drop in line voltageresulting in loss of power and overheating. Table 1shows correct size to use depending on cordlength and nameplate ampere rating. If in doubt,use the next heavier gauge. The smaller the gaugenumber, the heavier the cord.AmpereRatingMoreThanNotMoreThanVolts120240Total length ofcord in feet255050100100200AWG15030000 06 18 16 16 1406 10 18 16 14 1210 12 16 16 14 12Not12 16 14 12RecommendedExtension Cord RecommendationsTable 117

9.4 Switch lockoutThe table saw is equipped with a push-buttonswitch that will accept a safety padlock, as shownin Figure 20. To safeguard your machine fromunauthorized operation and accidental starting byyoung children, the use of a padlock (not included)is highly recommended. Place the key in a locationthat is inaccessible to children and others notqualified to use the tool.Figure 20: Switch Lock Out10.0 Adjustments10.1 Fence alignmentBefore using the Accu-Fence ® , verify that it isproperly aligned with the blade. Consult themanual, no. M-2195075Z, that accompanied thefence.10.2 Blade raising/tilt mechanismDo not try to force tiltingmechanism past the 45º or 90º stops. This maycause blade to go out of alignment.Refer to Figure 21:To raise or lower blade, loosen lock knob (A) andturn handwheel (B) on front of saw until desiredheight is reached. Tighten lock knob. The bladeshould be adjusted about 1/8" above top surface ofmaterial being cut.To tilt blade, turn lock knob (C) counter-clockwiseto loosen, turn handwheel (D) until desired angle isobtained, and retighten lock knob (C).Figure 2110.3 Miter gaugeRefer to Figure 22.10.3.1 Setting miter angleThe precision miter gauge has a rack and pinionadjustment for setting the angle. To operate:1. Slide miter gauge into one of the slots on tabletop.2. Loosen lock handle (A, Figure 22) by turningcounterclockwise.3. Pull out spring-loaded knob (C) and rotateknob until body (B) of miter gauge is at thedesired angle as indicated on the scale.4. Tighten lock handle (A).10.3.2 Indent settingsThere are indents at the 0º, 30º and 45º right andleft positions. At these settings, release knob (C) toengage stop rod. Then tighten lock handle (A).Note: Do not rely solely on the indents for anaccurate setting. After the stop rod engages at the0º, 30º and 45º positions, make a fine adjustmentwith the knob (C) if necessary, setting it against thescale indicator (G).10.3.3 Extension plateThe extension plate (D, Figure 22) can be adjustedby sliding to the right or left or removed entirely.To adjust, loosen two lock handles (E), position theextension plate and retighten lock handles. Makesure end of extension plate is not in the blade’spath.NOTE: The lock handles (E) are adjustable. Pullout on a handle, rotate it to different position, thenrelease, making sure it seats itself upon the pin.To remove extension plate, slide it completely offand remove lock handles (E) and mountinghardware.10.3.4 Calibration1. Place miter gauge in one of the slots on thetable top.2. Set miter gauge at 90º to blade (0º setting onthe scale) by loosening lock handle (A), thenpulling out spring-loaded knob (C) and turningthe body (B) until 0º is indicated on scale.3. Measure the accuracy of the gauge againstthe slot with a combination square.If adjustment is necessary:4. Adjust body (B) until it is perfectly square (90º)to miter slot.5. Tighten lock handle (A).6. Verify that scale indicator (G) reads 0º. Iffurther adjustment is needed:18

7. Loosen screw (F) and adjust indicator (G) untilit reads 0º.8. Tighten screw (F).NOTE: The bar of the miter gauge has two slotswith set screws (H). Adjust these set screws (4mmhex key) to eliminate any play between bar andmiter slot.Figure 2310.4.2 45° Blade stopRepeat steps 1 through 4 above for 45° setting, asshown in Figure 24. The 45° stop is shown at C,Figure 25.Figure 2210.4 Positive blade stopsThe stops for 90°, 45° blade tilt, and elevationsettings have all been factory set, and shouldrequire no immediate adjustment. The settingsshould be confirmed by the operator, however, andespecially if cuts become inaccurate.10.4.1 90° Blade stop1. Disconnect machine from power source.2. Make sure table insert has been leveled withtable surface. See section 8.12.3. Raise blade all the way, and place a 90°square on the table and against the blade(Figure 23). Make sure that a blade tooth doesnot obstruct the actual reading.4. Tilt blade with handwheel as needed untilsquare and blade are flush.5. If adjustment is required, loosen the twosetscrews on 90° stop collar (A, Figure 25 –3mm hex key) and rotate collar along the leadscrew to needed position. Verify the newsetting.6. Loosen screw on pointer (B, Figure 25), andadjust pointer to zero. Retighten screw.Figure 24Figure 2510.4.3 Blade elevation stopsLower blade all the way; it should drop completelybelow the table surface. If it does not, adjustamount of drop using two stop screws (D, Figure26).19

Figure 2610.5 Riving knife alignmentThe riving knife must be aligned with the blade forproper and safe operation of the table saw. Thishas been set by the manufacturer, but should beverified by the operator.1. Disconnect machine from power source.2. Install riving knife and tighten lever (H, Figure18).3. Place a straight edge against blade and rivingknife; it should lie flush against both surfaces.See Figure 27.4. If correction is needed, remove straight edge,table insert, and riving knife and locate four setscrews (E, Figure 28) through the corner holesof clamp block.5. Rotate any of the four set screws as needed totilt the angle of the clamp block, and thus theriving knife.6. Install riving knife and verify the setting withthe straight edge. Make further adjustments asneeded.Figure 27Figure 2810.6 Low profile riving knifeA low profile riving knife is included with your saw.It mounts and adjusts in the same manner as thestandard riving knife. The low profile riving knifesits just below top of blade and is used for makingnon-through cuts. The blade guard is not used withthis knife, so extra precautions should be takenduring operation.10.7 Trunnion adjustmentIf backlash develops in the trunnion assembly, itcan be adjusted out using the screws (6mm hexkey) at front and back of cabinet (F, Figure 25shows front screw). Front and rear trunnionsshould receive the same amount of spring tensionfrom the screws.10.8 Table to blade alignmentRefer to Figures 29 and 30.The table has been squared to the blade by themanufacturer and no adjustment is necessary now.If cuts become inaccurate, check table-bladesquareness and correct if necessary. Use the miterslot to do this:1. Disconnect saw from power source.2. Raise blade to maximum height.3. Mark one tooth (A, Figure 29) with a greasepencil and position the tooth slightly above thetop edge of table at the front.4. Raise the miter gauge slightly out of its slot toserve as a shoulder. Using a sliding square (B)against the side of the bar, slide the scale overuntil it touches the tip of the blade, and lockthe scale in position.20

1. Loosen screw (A) and hex nut (B) and pivotmotor upward to release tension on belt. Ifgreater movement is needed, remove screw(A) and pivot motor further.2. Replace belt.3. Reinstall screw (A) and push down on motor totension new belt.4. Tighten screw (A) and hex nut (B).Figure 29Figure 31Figure 305. Rotate marked tooth (A) so that it is slightlyabove table top at the rear and, using thesquare as before, verify that the distance tothe blade is the same. See Figure 30. If thedistances are not the same, make a carefulnote of the difference.6. Loosen table screws (item #30, section16.1.1), and nudge table according to thedistance you noted.7. Retighten screws firmly.8. Verify the alignment, angle pointer setting,fence setting, etc. Make any neededadjustments.10.9 Belt tension and replacementTension of the drive belt should be inspected afterthe first few days of operation, as it may stretchslightly during initial use; also inspect it periodicallythereafter.To tighten belt:1. Disconnect machine from power source.2. Loosen screw (A, Figure 31) and hex nut (B,Figure 31).3. Press down on motor while retightening screw(A) and hex nut (B).If belt shows signs of wear, fraying, cracks, etc. itshould be replaced:11.0 OperationsNOTE: If the saw is to be used without the metalstand provided, care must be taken to provide ahole in the stand or bench used by the operator tofacilitate removal of sawdust.If there is any tendency toslide, walk, or tip over during operation, thestand or bench MUST be secured to the floor.Familiarize yourself with the location and operationof all controls and adjustments and the use ofaccessories such as miter gauge and rip fence.11.1 Start/stop switchThis table saw has a manualswitch. If the power goes out during operation,push the STOP button. Otherwise, the saw willstart up when power is restored.11.2 Kickback preventionSerious injury can result from kickbacks whichoccur when a workpiece binds on the saw blade orbinds between the blade and rip fence or otherfixed object. This binding can cause the workpieceto lift up and be thrown toward the operator.Listed below are conditions which can causekickbacks: Confining the cutoff piece whencrosscutting or ripping.21

Releasing the workpiece beforecompleting operation or not pushing workpiece all the way past saw blade. Not using the splitter/riving knife whenripping or not maintaining alignment of thesplitter/riving knife with the saw blade. Using a dull saw blade. Not maintaining alignment of the rip fenceso that it tends to angle toward rather thanaway from the saw blade front to back. Applying feed force when ripping to thecutoff (free) section of the workpieceinstead of the section between saw bladeand fence. Ripping wood that is twisted (not flat), ordoes not have a straight edge, or hastwisted grain.To minimize or prevent injury from kickbacks: Avoid conditions listed above. Wear a safety face shield, goggles, orglasses. Do not use the miter gauge and rip fencein the same operation unless provision ismade by use of a facing board on thefence so as to allow the cutoff section ofthe workpiece to come free before theactual cut begins (See Figure 39). As the machine receives use, theoperation of the anti-kickback pawlsshould be checked periodically (Figure32). If the pawls do not stop the reversemotion of a workpiece, resharpen all thepoints.narrow (6" width or less), or thin work. Usea push block or miter gauge hold-downwhen dadoing or molding. Never use the fence as a length stopwhen crosscutting. Do not hold or touchthe free end or cutoff section of aworkpiece. On through-sawing operations,the cutoff section must NOT be confined. Always keep your hands out of line of thesaw blade and never reach back of thecutting blade with either hand to hold theworkpiece. Bevel ripping cuts should always be madewith the fence on the right side of sawblade so that the blade tilts away from thefence and minimizes the possibility of thework binding and the resulting kickback.11.3 Rip sawingRipping is where the workpiece is fed with the graininto the saw blade using the fence or otherpositioning device as a guide to ensure desiredwidth of cut (Figure 33).Before starting a ripping cut,verify that fence is clamped securely andaligned properly. Never rip freehand or use miter gauge incombination with the fence. Never rip workpieces shorter than the sawblade diameter. Never reach behind the blade with eitherhand to hold down or remove the cutoffpiece with the saw blade rotating.Figure 32 Where possible, keep your face and bodyout of line with potential kickbacksincluding when starting or stopping themachine. Dull, badly set, improper, or improperlyfiled cutting tools, and cutting tools withgum or resin adhering to them can causeaccidents. Never use a cracked sawblade. The use of a sharp, wellmaintained, and correct cutting tool for theoperation will help avoid injuries. Support the work properly and hold itfirmly against gauge or fence. Use a pushstick or push block when ripping short,22Figure 33Always use blade guard, splitter/riving knife andanti-kickback pawls. Make sure splitter/riving knifeis properly aligned. When wood is cut along thegrain, the kerf tends to close and bind on the bladeand kickbacks can occur.

Figure 34The rip fence (A, Fig. 34) should be set for thewidth of the cut by using the scale on the front rail,or by measuring the distance between blade (A)and fence (B). Stand out of line with saw blade andworkpiece to avoid sawdust and splinters comingoff the blade or a potential kickback.If the work piece does not have a straight edge,nail an auxiliary straight edged board on it toprovide one against the fence. To cut properly, theboard must make good contact with the table. If itis slightly warped, turn the hollow side down. Donot attempt to cut boards with significant warp.In ripping, use one hand to hold the board downagainst the fence or fixture, and the other to push itinto the blade between blade and fence. Ifworkpiece is narrower than 6" or shorter than 12",use a push stick or push block to push it throughbetween fence and blade (Figure 35). Never pushin a location such that the pushing hand is in linewith the blade. Move the hand serving as a holddowna safe distance from blade as cut nearscompletion.For very narrow ripping where a push stick cannotbe used, use a push block or auxiliary fence.Always push the workpiece completely past theblade at the end of a cut to minimize the possibilityof a kickback.Figure 36When ripping long boards, use a support at front oftable (C, Figure 36), such as a roller stand, and asupport or "tailman" at the rear (D).Never use the rip fence beyond the point where thecarriage is flush with the end of the rails.Have the blade extend about 1/8" above the top ofthe workpiece. Exposing the blade above this pointcan be hazardous.11.4 ResawingResawing is a ripping operation in which thickboards are cut into thinner ones. Note: A band sawis the ideal tool for resawing.If the table saw is used forresawing, take precautions such as using anauxiliary fence, resaw barrier or similar devicesto stabilize the workpiece and provide operatorsafety.Narrow boards up to 3" can be resawn in one pass.Wider boards up to 6" must be resawn in twopasses.In resawing wider boards, adjust the blade heightso as to overlap the two cuts by 1/2" as shown inFigure 37. Too deep a first cut can result in bindingand possible kickbacks on the second cut. Alwaysuse the same side of the board against the fencefor both cuts.Figure 3523

11.5 CrosscuttingFigure 37Crosscutting is where the workpiece is fed crossgrain into the saw blade using the miter gauge tosupport and position the workpiece (Figure 38).Do not crosscut workpieces shorter than 6". Beforestarting a cut, be sure the miter gauge is securelyclamped at the desired angle. Hold the workpiecefirmly against the table and back against the mitergauge. Always use the saw guard and riving knifeand make sure the riving knife is properly aligned.For 90 degree crosscutting, most operators preferto use the left-hand miter gauge slot. When using itin this position, hold the workpiece against thegauge with the left hand and use the right hand toadvance the workpiece. When using the right handslot for miter and compound crosscutting so thatthe blade tilts away from the gauge, the handpositions are reversed.When using the miter gauge, the workpiece mustbe held firmly and advanced smoothly at a slowrate. If the workpiece is not held firmly, it canvibrate causing it to bind on the blade and dull thesaw teeth.Figure 38Crosscutting should never be done freehand norshould the fence be used as an end stop unless anauxiliary block (E, Figure 39) is clamped to thefront of the blade area such that the cutoff piececomes free of the block before cutting begins.Figure 39Length stops should not be used on the free end ofthe workpiece in the cutoff area.Figure 40To augment the effectiveness of the miter gauge incrosscutting, some users mount an auxiliarywooden extension face (F, Figure 40) with a gluedonstrip of sandpaper (G) to the miter gauge.Provide auxiliary support for any workpieceextending beyond the table top with a tendency tosag and lift up off the table.Have the blade extend about 1/8" above the top ofthe workpiece. Exposing the blade above this pointcan be hazardous.11.6 Bevel and miter operationsBevel cut – A bevel cut is a special type ofoperation where the saw blade is tilted at an angleless than 90 degrees to the table top (Figure 41).Operations are performed in the same manner asripping or crosscutting, except the fence or mitergauge should be used on the right-hand side of theblade to provide added safety in avoiding a bindingaction between blade and table top. When bevelingwith the miter gauge, the workpiece must be heldfirmly to prevent creeping.24

Figure 41Mitering – Crosscuts made at an angle to the edgeof the workpiece are called miters (Figure 42). Setthe miter gauge at the required angle, and makethe cut the same as a normal crosscut except theworkpiece must be held extra firmly to preventcreeping.The process of cutting 1/8" to 13/16" grooves inworkpieces is accomplished by the use of astacked dado blade set or an adjustable type blademounted on the saw arbor. By using variouscombinations of stacked dado blades, or properlysetting the dial on an adjustable blade, an accuratewidth dado can be made. This is very useful forshelving, making joints, tenoning, etc.The guard, riving knife, and anti-kickback pawlssupplied with the saw should be used for all cuttingoperations where they can be used. Whenperforming operations where the guard cannot beused, as in some dadoing operations, alternativesafety precautions should be taken. These includepush sticks, feather boards, filler pieces, fixtures,jigs and any other appropriate device that can beutilized to keep operators’ hands away from theblade. Upon completion of the operation requiringremoval of the guard, the entire guard assemblymust be placed back on the machine in its properworking order.Never use a dado head in atilted position. Never operate the saw withoutthe blade guard, riving knife and anti-kickbackpawls for operations where they can be used.Figure 42Note: When making compound miters (with bladetilted) use the miter gauge in the right hand slot toprovide more hand clearance and safety.Have the blade extend only 1/8" above the top ofthe workpiece. Exposing the blade above this pointcan be hazardous.11.7 Dado cuttingDadoing is cutting a wide groove into a workpieceor cutting a rabbet along the edge of a workpiece.A dado insert (optional accessory, not provided)shown in Figure 43, is necessary for this type ofoperation.Do not use the standard tableinsert for dadoing operations.Figure 4325

12.0 Safety devicesFeather boardFeather boards can be purchased at most toolstores, or made by the operator to suit particularapplications. The feather board (Figure 44) shouldbe made of straight grain hardwood approximately1" thick and 4" to 8" wide depending on the size ofthe machine. The length is developed inaccordance with intended use.Feather boards can be fastened to the table or ripfence by use of C-clamps. Alternatively, drilled andtapped holes in the table top allow the use of wingnuts and washers as a method of clamping. If thismethod of fastening is used, provide slots in thefeather board for adjustment. (The illustrationshows a method of attaching and use of thefeather board as a vertical comb. The horizontalapplication is essentially the same except that theattachment is to the table top.)Figure 45 – Filler PiecePush stick and push blockThe use of a push block or push stick provides anadded level of safety for the operator. A push stickis included with your table saw, but you may wishto make others personalized for different cuttingprocedures. The templates in Figures 46 and 47offer construction details.Figure 46 – Push Block TemplateFiller pieceFigure 44A filler piece (Figure 45) is necessary for narrowripping and permits the blade guard to remain onthe machine. It also provides space for the safeuse of a push stick.26

Wipe down table surface and T-slots, andapply a rust preventive to them. Clean pitch and resin from saw blade.Weekly: Clean motor housing with compressed air. Wipe down fence rails with a dry siliconlubricant.LubricationRefer to Figure 48.Lower the arbor all the way, and lubricate thefollowing elements with a lithium grease every 12months, or more frequently if needed. Clean theelements first with a solvent/degreaser and a softrag. Blade angling trunnions (A, Figure 48). Wipe a light coat of grease on theelevating rods (B). Threads of blade elevating screw (C) Threads of blade tilting screw (D).Raise and lower arbor, and tilt it back and forth, todistribute the grease.Check all adjustments after lubricating.Figure 47 – Push stick template13.0 MaintenanceMiscellaneousFigure 48Always disconnect power tothe machine before performing maintenance.Failure to do this may result in seriouspersonal injury.CleaningClean the table saw according to the schedulebelow to ensure maximum performance. Theschedule assumes the saw is being used everyday.Daily:Always be aware of the condition of your machine.Routinely check the condition of the following itemsand repair or replace as necessary: Mounting bolts (tighten) Power switch Saw blade (cracks, worn or dull teeth, etc.) Blade guard and riving knife Drive belt (cracks, frays, worn areas, etc.)27

14.0 Optional accessoriesThese accessory items, purchased separately, canenhance the functionality of your table saw.Contact your dealer to order, or call Powermatic atthe phone number on the cover.p/n 1791088 – Dado insert for 64B table sawp/n 708118 – Universal mobile baseFigure 4928

15.0 Troubleshooting the 64B Table SawTable 2Trouble Probable Cause RemedyTable saw will not start.Excessive vibration.Cuts out-of-squarewhen crosscutting.Motor stalls orworkpiece binds orburns.Cuts not true at 90 or 45degrees.Tilting or Raisinghandwheel difficult toturn.Motor overheatsMotor starts slowly orfails to come up to fullspeed.Motor fails to developfull power.No incoming power.Check all plug connections.Fuse blown, or circuit breaker tripped. Replace fuse, or reset circuit breaker.Cord damaged.Replace cord.Tilting or raising lock knobs not tightened. Tighten lock knobs on handwheels.Machine not resting evenly on floor.Adjust foot pad(s). If saw is secured tofloor, use shims as needed.Blade out of balance.Replace blade.Pulley loose.Check motor pulley and spindle pulley.Tighten set screws if needed.Belt is worn, cracked or frayed.Replace belt.Motor not functioning properly.Have motor checked by a qualifiedinspector. Repair or replace.Miter gauge out of adjustment.Re-set stops and pointer on gauge.(Section 10.3).Miter slot misaligned. Realign table to blade (Section 10.8).Excessive feed.Reduce feed.Dull or incorrect blade.Replace blade; use proper type of bladefor cut needed.Miter slot misaligned. Realign table to blade (Section 10.8).Fence misaligned.Motor malfunction.Realign fence (see Accu-Fence®manual).Have motor checked by a qualifiedinspector. Repair or replace.Stop screws not set properly. Readjust screws (Section 10.4).Lock knob not released.Worm and worm gear segment caked withsawdust and pitch.Worm and worm gear segment out ofalignment.Motor overloaded.Improper cooling of motor; lack of aircirculation.Low voltage.Centrifugal switch not operating.Motor malfunction.Power line overloaded.Undersized wires in supply system.Low voltage.Motor malfunction.16.0 Replacement PartsLoosen lock knob.Clean and regrease worm and worm gearsegment.Realign worm with segment.Identify and correct overload condition,e.g. excessive feed rate of stock.Clean sawdust from fan and duct areas ofmotor.Request voltage check from powercompany and correct low voltagecondition.Replace centrifugal switch (qualifiedpersonnel only).Have motor checked by a qualifiedinspector. Repair or replace.Correct overload condition.Increase supply wire size.Request voltage check from powercompany and correct low voltagecondition.Have motor checked by a qualifiedinspector. Repair or replace.Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848 Monday through Friday (see our website for business hours, www.powermatic.com). Having theModel Number and Serial Number of your machine available when you call will allow us to serve you quicklyand accurately.29

16.1.1 Table and Cabinet Assembly – Exploded View30

16.1.2 Table and Cabinet Assembly – Parts ListIndex No Part No Description Size Qty1 ................ 64B-101..................... Table ........................................................................ ...................................... 12 ................ 64B-102..................... Table Extension ....................................................... ...................................... 2.................. 64B-TIA ..................... Table Insert Assembly (#3 thru #4).......................... ...................................... 13 ................ 64B-103..................... Table Insert .............................................................. ...................................... 14 ................ TS-1522011 .............. Socket Set Screw .................................................... M5x5 ............................. 65 ................ 64B-105..................... Cover ....................................................................... ...................................... 16 ................ 3520B-126................. Handle ..................................................................... ...................................... 17 ................ 64B-107..................... Handwheel ............................................................... ...................................... 18 ................ 64B-108..................... Cover Plate .............................................................. ...................................... 19 ................ 64B-109..................... Lead Screw .............................................................. ...................................... 110 .............. 64B-110..................... Angle Scale.............................................................. ...................................... 111 .............. BB-6201ZZ ................ Ball Bearing ............................................................. 6201ZZ.......................... 112 .............. 64B-112..................... Cabinet .................................................................... ...................................... 113 .............. TS-1523021 .............. Socket Set Screw .................................................... M6x8 ............................. 414 .............. TS-1523011 .............. Socket Set Screw .................................................... M6x5 ............................. 415 .............. 64B-115..................... Bushing .................................................................... ...................................... 216 .............. 64B-116..................... Bushing .................................................................... ...................................... 217 .............. 64B-117..................... Spring Pin ................................................................ Ø4x25 mm .................... 118 .............. TS-1540061 .............. Hex Nut .................................................................... M8 ................................. 219 .............. TS-2361081 .............. Lock Washer ............................................................ M8 ................................. 620 .............. TS-1550061 .............. Flat Washer ............................................................. M8 ................................. 621 .............. TS-1504071 .............. Socket Head Cap Screw.......................................... M8x35 ........................... 222 .............. 64B-122..................... Spring Pin ................................................................ Ø3x12 mm .................... 223 .............. 64B-123..................... Lock Bushing ........................................................... ...................................... 124 .............. 64B-124..................... Lock Knob ................................................................ ...................................... 125 .............. LM000636 ................. Warning Label.......................................................... ...................................... 126 .............. 6290630 .................... Strain Relief ............................................................. 7W-2 ............................. 327 .............. TS-1550031 .............. Flat Washer ............................................................. M5 ................................. 128 .............. 64B-128..................... Lock Knob ................................................................ ...................................... 129 .............. 64B-129..................... I.D label.................................................................... ...................................... 130 .............. TS-1490031 .............. Hex Cap Screw ........................................................ M8x20 ........................... 431 .............. TS-1491041 .............. Hex Cap Screw ........................................................ M10x30 ......................... 632 .............. TS-2361101 .............. Lock Washer ............................................................ M10 ............................... 633 .............. TS-1550071 .............. Flat Washer ............................................................. M10 ............................... 634 .............. 64B-134..................... Power Cord .............................................................. ...................................... 135 .............. 64B-135..................... Motor Cord ............................................................... ...................................... 136 .............. TS-081C082 .............. Phillips Pan Head Machine Screw ........................... #10-24x1-1/2”................ 237 .............. 6296133 .................... Switch Push Button.................................................. ...................................... 138 .............. 6291367 .................... Switch Bracket ......................................................... ...................................... 139 .............. TS-0733031 .............. Star Washer ............................................................. #10 ................................ 240 .............. 6296128 .................... Switch ...................................................................... ...................................... 141 .............. 6291366 .................... Switch Box ............................................................... ...................................... 142 .............. TS-0560071 .............. Hex Nut .................................................................... #10-24 ........................... 243 .............. TS-1533032 .............. Phillips Pan Head Machine Screw ........................... M5x10 ........................... 244 .............. TS-0733041 .............. Star Washer ............................................................. 1/4" ................................ 245 .............. TS-1540031 .............. Hex Nut .................................................................... M5 ................................. 246 .............. TS-0720071 .............. Lock Washer ............................................................ 1/4" ................................ 147 .............. TS-0050031 .............. Hex Cap Screw ........................................................ 1/4"-20x3/4” .................. 148 .............. JPS10TSR-103 ......... Push Block ............................................................... ...................................... 149 .............. 6290642 .................... Arbor Wrench........................................................... ...................................... 150 .............. JBOS5-105................ Open End Wrench ................................................... #14-#17 ......................... 151 .............. JBOS5-106................ Open End Wrench ................................................... #10-#12 ......................... 152 .............. TS-152707 ................ Hex Key ................................................................... 6mm .............................. 153 .............. TS-152705 ................ Hex Key ................................................................... 4mm .............................. 154 .............. TS-152704 ................ Hex Key ................................................................... 3mm .............................. 155 .............. JPS10TSR-105 ......... Hex Key ................................................................... 2.5mm ........................... 1.................. 64B-HP...................... Hardware Package (includes #31-33) ..................... ...................................... 131

16.2.1 Motor and Trunnion Assembly – Exploded View32

16.2.2 Motor and Trunnion Assembly – Parts ListIndex No Part No Description Size Qty1 ................ 64B-124..................... Lock Knob ................................................................ ...................................... 12 ................ 3520B-126................. Handle ..................................................................... ...................................... 13 ................ 64B-107..................... Handwheel ............................................................... ...................................... 14 ................ 64B-117..................... Spring Pin ................................................................ Ø4x25 mm .................... 15 ................ 64B-205..................... Lead Screw .............................................................. ...................................... 16 ................ 64B-206..................... Thrust Bearing ......................................................... 51104 ............................ 17 ................ 64B-207..................... Bushing .................................................................... ...................................... 18 ................ TS-154012 ................ Hex Nut .................................................................... M20-2.5P ...................... 19 ................ 64B-209..................... Bushing .................................................................... ...................................... 110 .............. 64B-210..................... Spacer ..................................................................... ...................................... 111 .............. TS-1522031 .............. Socket Set Screw .................................................... M5x10 ........................... 212 .............. TS-0267041 .............. Socket Set Screw .................................................... 1/4”-20x3/8”................... 413 .............. 64B-213..................... Gear ......................................................................... ...................................... 214 .............. 64B-214..................... Pointer ..................................................................... ...................................... 115 .............. TS-1533052 .............. Phillips Pan Head Machine Screw ........................... M5x15 ........................... 816 .............. 64B-216..................... Lock Washer ............................................................ ...................................... 217 .............. 64B-217..................... Guide Shaft .............................................................. ...................................... 118 .............. TS-1541031 .............. Nylon Lock Hex Nut ................................................. M8 ................................. 119 .............. 64B-219..................... Bearing .................................................................... ...................................... 120 .............. 64B-220..................... Gear Cover .............................................................. ...................................... 121 .............. TS-1532042 .............. Phillips Pan Head Machine Screw ........................... M4x12 ........................... 322 .............. TS-1550021 .............. Flat Washer ............................................................. M4 ................................. 323 .............. 64B-223..................... Poly-V Belt ............................................................... 188J .............................. 124 .............. 64B-224..................... Socket Head Cap Screw.......................................... M8x65 ........................... 125 .............. TS-1550061 .............. Flat Washer ............................................................. M8 ................................. 226 .............. 64B-226..................... Spring ...................................................................... ...................................... 127 .............. 64B-227..................... Trunnion................................................................... ...................................... 228 .............. TS-1491031 .............. Hex Cap Screw ........................................................ M10x25 ......................... 429 .............. TS-2361101 .............. Lock Washer ............................................................ M10 ............................... 430 .............. 64B-230..................... Center Trunnion ....................................................... ...................................... 131 .............. 64B-231..................... Screw ....................................................................... ...................................... 132 .............. 64B-232..................... Support Base ........................................................... ...................................... 133 .............. TS-1482031 .............. Hex Cap Screw ........................................................ M6x16 ........................... 234 .............. TS-1550041 .............. Flat Washer ............................................................. M6 ................................. 235 .............. 64B-235..................... Cover ....................................................................... ...................................... 136 .............. TS-1550031 .............. Flat Washer ............................................................. M5 ................................. 537 .............. 6290693 .................... Arbor Nut ................................................................. ...................................... 138 .............. 6290598 .................... Flange ...................................................................... ...................................... 139 .............. 64B-239..................... Arbor ........................................................................ ...................................... 140 .............. 64B-240..................... Clamp ...................................................................... 3” ................................... 241 .............. 64B-241..................... Hose ........................................................................ ...................................... 142 .............. 64B-242..................... Nut ........................................................................... ...................................... 143 .............. 64B-243..................... Lock Handle ............................................................. ...................................... 144 .............. 64B-244..................... Bolt........................................................................... ...................................... 145 .............. 64B-245..................... Holding Plate ........................................................... ...................................... 146 .............. TS-1524011 .............. Socket Set Screw .................................................... M8x8 ............................. 447 .............. 64B-247..................... Support Base ........................................................... ...................................... 148 .............. 64B-248..................... Low Profile Riving Knife ........................................... ...................................... 149 .............. TS-1550041 .............. Flat Washer ............................................................. M6 ................................. 150 .............. 64B-250..................... Bolt........................................................................... ...................................... 151 .............. 64B-251..................... Spring ...................................................................... ...................................... 152 .............. 64B-252..................... Moving Rod.............................................................. ...................................... 253 .............. TS-1504041 .............. Socket Head Cap Screw.......................................... M8x20 ........................... 254 .............. TS-1504071 .............. Socket Head Cap Screw.......................................... M8x35 ........................... 255 .............. 64B-255..................... S-Ring ...................................................................... S15................................ 156 .............. 64B-256..................... Bushing .................................................................... ...................................... 257 .............. 64B-257..................... Lead Screw .............................................................. ...................................... 158 .............. 64B-258..................... Thrust Bearing ......................................................... ...................................... 159 .............. 64B-259..................... Ball Bearing ............................................................. 6202-5/8” bore .............. 233

Index No Part No Description Size Qty60 .............. 64B-260..................... Shaft ........................................................................ ...................................... 161 .............. 64B-261..................... Bracket..................................................................... ...................................... 162 .............. 64B-262..................... Bearing .................................................................... ...................................... 463 .............. 64B-263..................... Thread Housing ....................................................... ...................................... 164 .............. 64B-264..................... Bushing .................................................................... ...................................... 165 .............. 6290630 .................... Strain Relief ............................................................. 7W-2 ............................. 166 .............. 64B-266..................... Hex Nut (L.H Thread) .............................................. M14-2.0P ...................... 167 .............. 64B-267..................... Key........................................................................... 5x5x25 mm ................... 168 .............. 64B-268..................... Motor Pulley ............................................................. ...................................... 169 .............. 64B-269..................... Plate......................................................................... ...................................... 170 .............. TS-2361051 .............. Lock Washer ............................................................ M5 ................................. 271 .............. TS-1523031 .............. Socket Set Screw .................................................... M6x10 ........................... 272 .............. 64B-272..................... Motor........................................................................ ...................................... 1.................. 64B-272MF ............... Motor Fan (not shown)............................................. ...................................... 1.................. 64B-272MFC ............. Motor Fan Cover (not shown) .................................. ...................................... 1.................. 64B-272CS................ Centrifugal Switch (not shown) ................................ ...................................... 1.................. 64B-272SCC ............. Starting Capacitor Cover (not shown)...................... ...................................... 1.................. 64B-272RCC ............. Running Capacitor Cover (not shown)..................... ...................................... 1.................. 64B-272SC................ Starting Capacitor (not shown) ................................ 400MFD, 125VAC ......... 1.................. 64B-272RC ............... Running Capacitor (not shown) ............................... 30μf, 250VAC ............... 1.................. 64B-272JB ................ Junction Box (not shown) ........................................ ...................................... 1.................. 64B-272JBC .............. Junction Box Cover (not shown) .............................. ...................................... 1.................. 64B-272OL ................ Overload (not shown) .............................................. ...................................... 1.................. 64B-272DC ............... Dust Cover (not shown) ........................................... ...................................... 173 .............. TS-1550071 .............. Flat Washer ............................................................. M10 ............................... 174 .............. TS-1491031 .............. Hex Cap Screw ........................................................ M10x25 ......................... 175 .............. TS-0680081 .............. Flat Washer ............................................................. 5/8” ................................ 176 .............. 64B-276..................... Nylon Lock Hex Nut ................................................. 5/8”-11........................... 177 .............. TS-1482061 .............. Hex Cap Screw ........................................................ M6x30 ........................... 278 .............. TS-2311061 .............. Hex Nut .................................................................... M6 ................................. 2.................. 64B-ALA .................... Arbor Lock Assembly (82# thru 88#) ....................... ...................................... 179 .............. TS-1502041 .............. Socket Head Cap Screw.......................................... M5x16 ........................... 280 .............. TS-2361051 .............. Lock Washer ............................................................ M5 ................................. 281 .............. TS-1550031 .............. Flat Washer ............................................................. M5 ................................. 282 .............. 64B-282..................... Bracket..................................................................... ...................................... 183 .............. 64B-283..................... Spring Pin ................................................................ Ø3x25 mm .................... 184 .............. 64B-284..................... Lock Shaft ................................................................ ...................................... 185 .............. 64B-285..................... Spring ...................................................................... ...................................... 186 .............. TS-1550061 .............. Flat Washer ............................................................. M8 ................................. 187 .............. 64B-287..................... Handle ..................................................................... ...................................... 188 .............. TS-1541001 .............. Hex Nylon Lock Nut ................................................. M4 ................................. 134

16.3.1 Stand Assembly – Exploded View16.3.2 Stand Assembly – Parts ListIndex No Part No Description Size Qty1 ................ 64B-301..................... Leg ........................................................................... ...................................... 42 ................ 64B-302..................... Upper Side Brace .................................................... ...................................... 13 ................ 64B-303..................... Upper Short Brace ................................................... ...................................... 24 ................ 64B-304..................... Upper Long Brace.................................................... ...................................... 15 ................ 64B-305..................... Lower Short Brace (includes stripe)......................... ...................................... 26 ................ 64B-306..................... Lower Long Brace (includes stripe) ......................... ...................................... 27 ................ 64B-307..................... Powermatic Nameplate Label .................................. 1-1/2”W x 10”L .............. 18 ................ 64B-308..................... Miter Gauge Hook.................................................... ...................................... 19 ................ 64B-309..................... Fence Body Hook .................................................... ...................................... 210 .............. 64B-310..................... Hook ........................................................................ ...................................... 111 .............. 64B-311..................... Rubber Foot Pad ..................................................... ...................................... 412 .............. 64B-312..................... Carriage Bolt ............................................................ M8x16 ......................... 2413 .............. TS-1550061 .............. Flat Washer ............................................................. M8 ............................... 4014 .............. TS-2361081 .............. Lock Washer ............................................................ M8 ............................... 2815 .............. TS-1540061 .............. Hex Nut .................................................................... M8 ............................... 3616 .............. TS-1533052 .............. Phillips Pan Head Machine Screw ........................... M5x15 ........................... 817 .............. TS-1540031 .............. Hex Nut .................................................................... M5 ................................. 818 .............. TS-1490041 .............. Hex Cap Screw ........................................................ M8x25 ........................... 4.................. 64B-SHP ................... Stand Hardware Package (#12 thru #18) ................ ...................................... 1.................. 3520B-158................. Black Stripe.............................................................. ............................... per ft.35

16.4.1 Blade Guard and Miter Gauge Assemblies – Exploded View36

16.4.2 Blade Guard and Miter Gauge Assemblies – Parts ListIndex No Part No Description Size Qty.................. 64B-BGA ................... Blade Guard Assembly (#1 thru #31) ...................... ...................................... 11 ................ 64B-401..................... Riving Knife.............................................................. ...................................... 1.................. 64B-UGA ................... Upper Guard Assembly (#2 thru #31) ...................... ...................................... 12 ................ 64B-402..................... Support Arm............................................................. ...................................... 13 ................ 64B-403..................... Left side Blade Guard .............................................. ...................................... 14 ................ 64B-404..................... Right Side Blade Guard ........................................... ...................................... 15 ................ 64B-405..................... Plate......................................................................... ...................................... 16 ................ 64B-406..................... Anti-Kickback Pawl .................................................. ...................................... 27 ................ 64B-407..................... Spring ...................................................................... ...................................... 19 ................ TS-1533032 .............. Phillips Pan Head Machine Screw ........................... M5x10 ........................... 210 .............. TS-0640071 .............. Nylon Lock Hex Nut ................................................. 1/4”-20........................... 811 .............. TS-0813051 .............. Flat Head Screw ...................................................... 1/4”-20x5/8”................... 812 .............. TS-0680021 .............. Flat Washer ............................................................. 1/4” ................................ 813 .............. 64B-413..................... Spring Pin ................................................................ Ø6x30 mm .................... 114 .............. 64B-414..................... Spring Pin ................................................................ Ø3.5x28 mm ................. 215 .............. 64B-415..................... Spring Pin ................................................................ Ø5x35 mm .................... 117 .............. 64B-417..................... Shaft ........................................................................ ...................................... 118 .............. 64B-418..................... Holding Bracket ....................................................... ...................................... 119 .............. TS-1541021 .............. Nylon Lock Hex Nut ................................................. M6 ................................. 220 .............. TS-1482071 .............. Hex Cap Screw ........................................................ M6x35 ........................... 121 .............. 64B-421..................... Lock Handle ............................................................. ...................................... 122 .............. 64B-422..................... Holding Bracket ....................................................... ...................................... 124 .............. 64B-424..................... Front Shield ............................................................. ...................................... 125 .............. TS-1502021 .............. Socket Head Cap Screw.......................................... M5x10 ........................... 226 .............. 64B-426..................... Pivot Arm ................................................................. ...................................... 427 .............. 64B-427..................... Warning Label.......................................................... ...................................... 128 .............. TS-1481081 .............. Hex Cap Screw ........................................................ M5x35 ........................... 129 .............. TS-1550031 .............. Flat Washer ............................................................. M5 ................................. 130 .............. 64B-430..................... Bushing .................................................................... ...................................... 231 .............. TS-1541011 .............. Nylon Lock Hex Nut ................................................. M5 ................................. 1.................. 1791789 .................... Miter Gauge Assembly (#32 thru #52) ..................... ...................................... 132 .............. PM2000-323.............. Miter Gauge Body .................................................... ...................................... 133 .............. PM2000-324.............. Pin............................................................................ ...................................... 134 .............. PM2000-325.............. Miter Bar .................................................................. ...................................... 135 .............. PM2000-326.............. Guide Washer .......................................................... ...................................... 136 .............. PM2000-327.............. Flat Head Machine Screw........................................ M6x9 ............................. 137 .............. TS-0050051 .............. Hex Cap Screw ........................................................ 1/4”-20x1”...................... 238 .............. PM2000-329.............. Socket Head Cap Screw.......................................... M5x8 ............................. 239 .............. PM2000-330.............. Support Base ........................................................... ...................................... 140 .............. PM2000-331.............. Knob ........................................................................ ...................................... 141 .............. TS-1521011 .............. Socket Set Screw .................................................... M4x4 ............................. 142 .............. PM2000-333.............. Locking Handle ........................................................ ...................................... 243 .............. TS-0810012 .............. Phillips Pan Head Machine Screw ........................... #10-24x1/4” ................... 144 .............. PM2000-335.............. Pointer ..................................................................... ...................................... 145 .............. PM2000-336.............. Spring ...................................................................... ...................................... 146 .............. PM2000-337.............. Gear Shaft ............................................................... ...................................... 147 .............. PM2000-338.............. Scale ........................................................................ ...................................... 148 .............. PM2000-339.............. Rivet......................................................................... ...................................... 249 .............. PM2000-340.............. Handle ..................................................................... ...................................... 150 .............. TS-0680031 .............. Flat Washer ............................................................. 5/16” .............................. 151 .............. PM2000-342.............. Fence ....................................................................... ...................................... 152 .............. PM2000-343.............. Socket Set Screw .................................................... M8x6 ............................. 237

17.0 Electrical Connections17.1 Connections for 115 volt (64B Table Saw)400MFD 125 VAC30uf 250 VAC115V38

427 New Sanford RoadLaVergne, Tennessee 37086Phone: 800-274-6848www.powermatic.com40