Proposed Renovation of Former Jacinto Building - Clark Freeport Zone

More documents

Recommendations

Info

ALUMINUM GLASS WINDOWS (Supply and Install)Item 1008 (a) to (b)This item shall consist of furnishing all aluminum glass window materials, labor,tools and equipment required in undertaking the proper installation as shownon the Plans and in accordance with the specification.Frame and panel members shall be fabricated from extruded aluminum sectiontrue to details with clean, straight, sharply defined profiles and free fromdefects impairing strength or durability. Extruded aluminum section shallconform to the specification requirements defined in ASTM B 211.Weather strip shall be first class quality flexible vinyl forming an effective sealand without adverse deformation when installed.Main frame shall consist of head, sill and jamb. Window panel shall be jointedat corners with miter and fixed rigidly to ensure weather tightness.Sliding windows shall be provided with nylon sheave. Sliding panels shall besuspended with concealed roller overhead tracks with bottom guide pitchoutward and slotted for complete drainage. The sliding panels shall beprovided with interior handles. The locking device shall be a spring loadedextruded latch that automatically engages special frame hips.The contractor does not only protect all entrance units during the constructionphase but shall also be responsible for removal of protective materials andcleaning the aluminum surface including glazing before work is accepted by theEngineer.Aluminum shall be thoroughly cleaned with kerosene or gasoline diluted withwater and then wipes surface using clean cloth rugs. No abrasive cleaningmaterials shall be permitted in cleaning surface.Aluminum glass window fully equipped with fixing accessories and lockingdevices shall be measured in square meters actually installed in-place andaccepted to the satisfaction of the Engineer.WOODEN DOORSItem 1010 (a) to (b)This item shall consist of furnishing all materials, hardware, tools, labor andservices necessary for complete fabrication and installation of wooden doorsand the type and size as shown on the Plans and in accordance with the94Clark Development Corporation Proposed Renovation of Former Jacinto Building(Motorpool, Records, Warehouses and Maintenance Area)
specifications and applicable specification under Item 1003 on Carpentry andJoinery Works.Lumber of doors, jambs and panels when required, shall be kiln-dried withmoisture content of not more than 14 %.Wooden doors and frames shall be fabricated in accordance with the designsand sizes shown on the Plans. The fabricated products shall be finished square,smoothly sanded and free from damage or warpage.Wooden doors shall be measured and paid for on the basis of number of setscompletely installed and accepted by the Engineer. A set shall consist of paneldoor, jambs, anchors, door closer, and hardware including lockset.ROLLING UP DOORSItem 1011 (a) to (b)This item shall consist of furnishing all labor, tools, equipment and rolling updoor required as shown on the Plans and in accordance with this specification.Rolling up doors shall be surfaced mounted designed for exterior serviceopening as indicated on the Plans. Component parts shall conform with thefollowing material specifications:Curtain – shall be manufactured if interlocking curved or flat slats, rolled fromgalvanized and bonderized steel. Slats shall be of size and thickness towithstand 0.957 KPa windload.Counter balance barrel assembly shall include spring barrel which serves asload carrying beam encases counter balance mechanism and provided axisaround curtain coils. Hood shall be manufactured from 0.60mm thick(minimum) galvanized sheet metal, flanged at top for attachment to headerand flanged at bottom to provide longitudinal stiffness.Hood shall enclose curtain coil and counter balance mechanism. Brackets shallbe made of precisely formed plate with permanently sealed ball bearings,designed to enclose end of the curtain coil and provide support for counterbalance pipe at each end.Guides shall be fabricated from structural steel angles or precision roll formedchannels and angles. Especially adaptable for doors exposed to heavy windpressure. Designed with groove depths varying from 50mm depending uponthe width of the door, and set cut from the face of the wall to facilitate thetravel of the curtain.95Clark Development Corporation Proposed Renovation of Former Jacinto Building(Motorpool, Records, Warehouses and Maintenance Area)
Page 1 and 2:
Clark Development CorporationClark
Page 3 and 4:
Section I. Invitation to BidClark D
Page 5 and 6:
5. A complete set of Bidding Docume
Page 7 and 8:
Section II. Instructions to Bidders
Page 9:
A. General1. Scope of Bid1.1. The P
Page 12 and 13:
implementation of the project, if t
Page 14 and 15:
under ongoing contracts, including
Page 16 and 17:
6.8. Bidders should note that the P
Page 18 and 19:
Philippines, in which case the Engl
Page 20 and 21:
(i.2)a surety bond accompanied by a
Page 22 and 23:
15. Bid Prices15.1. The contract sh
Page 24 and 25:
draft/guarantee, or irrevocable let
Page 26 and 27:
19.3. The Bidder shall prepare an o
Page 28 and 29:
administrative, civil, and criminal
Page 30 and 31:
27. Detailed Evaluation and Compari
Page 32 and 33:
Calculated Bid to make a similar de
Page 34 and 35:
(a)Submission of the following docu
Page 36 and 37:
33. Notice to Proceed33.1. Within t
Page 38 and 39:
Bid Data SheetITBClause1.1. The PRO
Page 40 and 41:
14.2. No further instructions.15.4.
Page 42 and 43:
Section IV. General Conditions ofCo
Page 44 and 45:
27.RIGHT TO VARY...................
Page 46 and 47: 1.13. The Defects Liability Period
Page 48 and 49: 2.2. If sectional completion is spe
Page 50 and 51: particularly when they shall requir
Page 52 and 53: Procuring Entity shall rescind this
Page 54 and 55: and/or intended purpose of the same
Page 56 and 57: 15.2. The Contractor shall provide
Page 58 and 59: 16.5. All materials on the Site, Pl
Page 60 and 61: 18.5. When persons from either part
Page 62 and 63: (i) Employment of competent technic
Page 64 and 65: decision was wrongly taken, the dec
Page 66 and 67: 27. Right to Vary27.1. The Procurin
Page 68 and 69: 32. Management Conferences32.1. Eit
Page 70 and 71: 38. Uncorrected Defects38.1. The Pr
Page 72 and 73: (c)Include the valuations of approv
Page 74 and 75: (a)(b)(c)(d)(e)If the Procuring Ent
Page 76 and 77: unless there are justifiable reason
Page 78 and 79: consideration and the validity of t
Page 80 and 81: GCC ClauseSpecial Conditions of Con
Page 82 and 83: Section VI. Technical Specification
Page 84 and 85: Item 800 (b) Cleaning and Scrubbing
Page 86 and 87: in the approved Plan shall undertak
Page 88 and 89: The concrete materials shall be pro
Page 90 and 91: The quantity of metal structures to
Page 92 and 93: Valves for water supply system shal
Page 94 and 95: High Pressure Plastic Laminate comp
Page 98 and 99: Doors shall be operated and with pr
Page 100 and 101: Mortar mixture shall be freshly pre
Page 102 and 103: portion(s) shall not start until cl
Page 104 and 105: All panel board and metallic boxes
Page 106 and 107: Panel boards shall conform to the s
Page 108 and 109: Section VII. DrawingsSee attached10
Page 110 and 111: Section VIII. Bill of Quantities108
Page 112 and 113: Bid FormDate: ___________________IA
Page 114 and 115: Form of Contract AgreementTHIS Cont
Page 116 and 117: A C K N O W L E D G E M E N TREPUBL
Page 118 and 119: 6. [Name of Bidder] is authorizing
Page 120 and 121: Any one of the Following:o Computat
Page 122 and 123: Sample Forms of Eligibility, Techni
Page 124 and 125: Standard Form Number: SF-INFR-16Sta
Page 126 and 127: Standard Form Number: SF-INFR-20Rev
Page 128 and 129: we undertake to pay to the Entity u
Page 130 and 131: 2) if the Principal does not accept
Page 138 and 139: Standard Form Number: SF-INFR-48Qua
Page 140 and 141: DAYWORK SCHEDULEPROJECT : Proposed
show all

Proposed Renovation of Former Jacinto Building - Clark Freeport Zone

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?