SA-KIT_LP075-000 / SA-Kit_LP150-000 Linear potentiometer KIT ...

2D Debus & Diebold Meßsysteme GmbH, Alte Karlsruher Str. 8, D-76227 KarlsruheTel.: +49(0)721 94485-0 Fax.: +49(0)721 94485-29SA-KIT_LP075-000 / SA-Kit_LP150-000Linear potentiometer KIT SystemFunction‣ Changing of the resistor value, caused by mechanicmotions of the grinder bar‣ To measure linear motions e.g. front fork, steering,or rear wingNotice‣ Metal heads with thread Mx4 get fixed e.g. to thediving tube and fork bridge. You simply have to putthe potentiometer then on the already fixed metalheads.‣ Make sure that the potentiometer moves easily.‣ Have a look for the final studs.‣ To avoid that water enters the housing, pleasemount the grinder bar down below.Technical specifications SA-KIT_LP075-000 SA-KIT_LP150-000Electrical characteristicsElectrical stroke ± 1mm................... 75 150 mmRetracted mounting distance.......... 175 260 mmImpedance...................................... 3k 6k ΩLinearity........................................... 0.15 0.15 %Supply voltage................................. +5 +5 V dcSupply voltage (maximum).............. 65 130 V dcMechanical characteristicsConnector refer 2 nd page refer 2 nd pageCabletype PUR cable PUR cablewire cross section 3 x AWG24 3 x AWG24length........................ 1400 600 mmprefabricated............ Tyco pins Tyco pinsResolution....................................... 50 Mio cyclesWeight............................................. 60 95 gEnvironmentalOperating temperature.................... -40 to +85 -40 to +85 °CShock ⏐ During a time period of...... 40 ⏐ 10 40 ⏐ 10 G ⏐ msecVibration testet at⏐ with a frequency 12 ⏐ 1000 12 ⏐ 1000 G ⏐ HzOrdering informationArt.No.:.......................................................... SA-KIT_LP075-000 SA-KIT_LP150-000The specifications on this document are subject to change at 2D decision. 2D assumes noresponsibility for any claims or damages arising out of the use of this document, or from the use ofmodules based on this document, including but not limited to claims or damages based oninfringement of patents, copyrights or other intellectual property rights.2D Debus & Diebold Meßsysteme GmbHhttp://www.2D-datarecording.comhttp://www.2D-Kit-System.commail@2D-datarecording.com24.04.2009 / MF 2D Kit System: Sensors add-on kit

2D Debus & Diebold Meßsysteme GmbH, Alte Karlsruher Str. 8, D-76227 KarlsruheTel.: +49(0)721 94485-0 Fax.: +49(0)721 94485-29SA-KIT_LP075-000 / SA-Kit_LP150-000Linear potentiometer KIT SystemDimensionsPoti∅4.04.0∅12.9 12.96 mm11.3 mmlength length L1 of housingtotal length total length L2 L2stroke length of housing total length L2 in total length L2 out75 149 175 250150 234 260 410all values in mm, tolerance +/- 1mmM46.5 mmmetal heads mit thread M4(for easy and fast fixing)Connection adviceFront suspensionInterface unit (logger)(34pin AMP connector)Rear suspensionInterface unit (logger)(34pin AMP connector)Connector layoutSuespension FrontOpen wires, TycoPin Name Description Color10 Susp_F Signal (=Front suspension) white18 AGND Analog Ground black26 +5V Sensor supply (+5V) redConnector typeOpen wires prefabricated with Tyco® pins fordirect connection with interface unit (=AMPconnector)Pin Name Description ColorSuspension RearOpen wires, Tyco11 Susp_R Signal (=Rear suspension) white19 AGND Analog Ground black27 +5V Sensor supply (+5V) redThe specifications on this document are subject to change at 2D decision. 2D assumes noresponsibility for any claims or damages arising out of the use of this document, or from the use ofmodules based on this document, including but not limited to claims or damages based oninfringement of patents, copyrights or other intellectual property rights.2D Debus & Diebold Meßsysteme GmbHhttp://www.2D-datarecording.comhttp://www.2D-Kit-System.commail@2D-datarecording.com24.04.2009 / MF 2D Kit System: Sensors add-on kit