SPEED I QUALITY I AFFORDABILITY

More documents

Recommendations

Info

Wiring DetailsSWITCHING OPTIONSSCT Single Circuit. All lamps are wired to a single circuit.DCT Dual Circuit. Two light levels are achieved by switching separate rows of lamps in the samefixture on two independently switched circuits. Dual circuit fixtures share a common neutral.For fixtures or runs with 2 lamps in the cross section the standard DCT circuiting is one side wired tocircuit “A” and the other side wired to a circuit “B”.EL LUMEN OUTPUT PER 1-LAMP EMERGENCY BATTERY PACKLamp Type 32W T8 28W T5 54W T5HOLumens 700 800 825ELEL The default DCT for a fixture with 3 lamps (or more) in the cross section is the row of lamps onthe outside wired to a switched circuit “A” and the lamps located in the middle wired to a switchedcircuit “B”. EMERGENCY LIGHTING OPTIONSNumber of Emergency Modules1SE 1 Section. One 4FT module per run will have an Emergency Lighting option.2SE 2 Sections. Two 4FT modules per run.The standard maximum number of 4FT emergency modules is one per 4 / 8 /12 foot fixture section.Emergency TypeEL Emergency Battery Pack. Each battery pack will be connected to one lamp unless otherwise specified.EC Emergency Circuit. Each emergency/night light circuit will be connected to a single lamp whenonly one lamp is in the cross section. When two or more lamps are in the cross section the two mostouter lamps will be connected to emergency circuit.EC EC EC ECEC EN Emergency Battery Pack with emergency/night light circuit. The same lamp connections applyas emergency circuit, but when only battery power is available then the lamp connections stated foremergency battery pack apply.ECECECECECEC ECECECECEL EL EL EL EL EL PEERLESS LIGHTING
Wiring DetailsEMERGENCY WIRING OPTIONS (No option) Each emergency lighting section is powered at the support point that follows it. ELH Current load permitting, all emergency lighting modules are powered by through wire to oneemergency power feed located at the last support point in the fixture run.ELEL ELS Current load permitting, all emergency lighting modules are powered by a continuous throughwire to one emergency power feed location. The emergency lighting power feed is located at thefirst support point in the fixture run, often combined within the normal power feed cable sharing acommon neutral. Check local electrical code for compliance.ELS2 Same concept as ELS, with the addition of a separate neutral. This option sometimes requires aseparate J-box for emergency power with “F1” grid ceiling mounts.MAXIMUM RUN DISTANCEPER POWER FEEDLamps in Cross SectionLamp Type 120V 277V 347V1 T5HO 56' 124' 160'2 T5HO 28' 64' 80'3 T5HO 16' 40' 52'4 T5HO 12' 32' 40'1 T5 and T8 104' 240' 292'2 T5 and T8 52' 120' 148'3 T5 and T8 36' 80' 96'4 T5 and T8 24' 60' 72'Assumptions: Single circuit, noemergency lighting option, T8 .88 BFballast and T5/T5HO 1.0 BF ballast.Consult factory for other scenarios.EXAMPLE RUNS PEERLESS LIGHTING 21
Page 2 and 3: www.peerless-lighting.comPeerless m
Page 4: QuickShip Specification SheetsPEERL
Page 8 and 9: ®PARTIAL PERFSCEP option10CRM7QSsp
Page 10 and 11: 7CRM1QS7 ® INDIRECTSCEP optionspec
Page 12 and 13: ICM8QSIceTray®CURVED INDIRECT/DIRE
Page 14 and 15: BRM1QSBruno®INDIRECTspecifications
Page 17 and 18: Lightline®RECESSED LOUVER AND WALL
Page 19 and 20: Fixture OptionsGENERAL OPTIONSDU Cl
Page 21: F2 Mounting TypeF2 for use with har
Page 25 and 26: Application10’8’For specific ap
Page 28: PEERLESS LIGHTING

SPEED I QUALITY I AFFORDABILITY

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?