Proline Promass 83E/F/O Modbus RS485 Operating Instructions

More documents

Recommendations

Info

TroubleshootingProline Promass 83 Modbus RS485Modbus No. Device status message(local display)CauseRemedy / spare partRegister:6859Data type:IntegerRegister:6821Data type:String (18 byte)114 NOISE LIM. CH0 703 P: NOISE LIM. CH0!: # 703115 NOISE LIM. CH1 704 P: NOISE LIM. CH1!: # 704Overdriving of the internalanalog to digital converter.Causes:– Cavitation– Extreme pressure pulses– High gas flow velocityA continuation of themeasurement is still possible!Change or improve process conditions, e.g. byreducing the flow velocity.116 FLOW LIMIT 705 P: FLOW LIMIT$: # 705124 ADJ. ZERO FAIL. 731 P: ADJ. ZERO FAIL!: # 731The mass flow is too high.The electronics' measuringrange will be exceeded.The zero point adjustment isnot possible or has beencanceled.Reduce flowMake sure that zero point adjustment is carried out at"zero flow" only (v = 0 m/s).Page 98 • MN0M030Issue/Rev. 0.2 (12/12)
Proline Promass 83 Modbus RS485Troubleshooting9.4 Process errors without messagesSymptomsRectificationComment:You may have to change or correct certain settings of the function matrix in order to rectify faults. The functions outlined below, such as DISPLAY DAMPING, forexample, are described in detail in the "Description of Device Functions" manual.Measured-value reading fluctuateseven though flow is steady.1. Check the fluid for presence of gas bubbles.2. TIME CONSTANT function increase value ( OUTPUTS / CURRENT OUTPUT / CONFIGURATION3. DISPLAY DAMPING function increase value ( USER INTERFACE / CONTROL / BASIC CONFIGURATION)Flow values are negative, even thoughthe fluid is flowing forwards throughthe pipe.Change the setting in the INSTALLATION DIRECTION SENSOR function accordinglyMeasured-value reading or measuredvalueoutput pulsates or fluctuates, e.g.because of reciprocating pump,peristaltic pump, diaphragm pump orpump with similar deliverycharacteristic.Run the "Pulsating Flow" Quick Setup ä 62.If the problem persists despite these measures, a pulsation damper will have to be installed between pump and measuringdevice.There are differences between theflowmeter's internal totalizer and theexternal metering device.This symptom is due primarily to backflow in the piping, because the pulse output cannot subtract in the "STANDARD" or"SYMMETRY" measuring modes.The problem can be solved as follows:Allow for flow in both directions. Set the MEASURING MODE function to "Pulsating Flow" for the pulse output inquestion.Measured value reading shown ondisplay, even though the fluid is at astandstill and the measuring tube is full.1. Check the fluid for presence of gas bubbles.2. Activate the ON-VAL. LF-CUTOFF function, i.e. enter or increase the value for the low flow cut off ( BASICFUNCTION / PROCESS PARAMETER / CONFIGURATION).The fault cannot be rectified or someother fault not described above hasarisen.In these instances, please contact yourE+H service organization.The following options are available for tackling problems of this nature:Request the services of an service technicianIf you contact our service organization to have a service technician sent out, please be ready to quote the followinginformation:– Brief description of the fault– Nameplate specifications: order code, serial number ä 7Returning devices to Carry out the measures listed before you return a flowmeter requiring repair or calibration to . ä 107Always enclose a duly completed "Declaration of contamination" form with the flowmeter. You will find a preprintedblank of the Dangerous Goods Sheet at the back of this manual.Replace transmitter electronicsComponents in the measuring electronics defective order spare parts ä 101Issue/Rev. 0.2 (12/12) MN0M030 • Page 99
Page 1 and 2:
Issue/Rev. 0.2 (12/12)Coriolis Mass
Page 3 and 4:
Proline Promass 83 Modbus RS485Tabl
Page 5 and 6:
Proline Promass 83 Modbus RS485Safe
Page 7 and 8:
Proline Promass 83 Modbus RS485Iden
Page 9 and 10:
Proline Promass 83 Modbus RS485Iden
Page 12 and 13:
InstallationProline Promass 83 Modb
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
WiringProline Promass 83 Modbus RS4
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
OperationProline Promass 83 Modbus
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49: OperationProline Promass 83 Modbus
Page 60 and 61: EscCommissioningProline Promass 83
Page 62 and 63: CommissioningProline Promass 83 Mod
Page 64 and 65: CommissioningRecommended settings Q
Page 86 and 87: MaintenanceProline Promass 83 Modbu
Page 88 and 89: AccessoriesProline Promass 83 Modbu
Page 90 and 91: TroubleshootingProline Promass 83 M
Page 92 and 93: TroubleshootingModbus No. Device st
Page 94 and 95: TroubleshootingäProline Promass 83
Page 108 and 109: Technical dataProline Promass 83 Mo
Page 120 and 121: Technical dataPerformance character
Page 136 and 137: Technical dataLimiting flowPressure
Page 148 and 149:
Technical dataProline Promass 83 Mo
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Proline Promass 83 Modbus RS485Inde
Page 156 and 157:
Proline Promass 83 Modbus RS485Rela
Page 158:
The specifications contained herein
show all

Proline Promass 83E/F/O Modbus RS485 Operating Instructions

Create successful ePaper yourself

Delete template?

Save as template?