Proline Promass 83E/F/O Modbus RS485 Operating Instructions

More documents

Recommendations

Info

CommissioningProline Promass 83 Modbus RS485Recommended settingsQuick Setup "Gas Measurement"HOME position F MEASURED VARIABLE (A)MEASURED VARIABLE O QUICK SETUP (B)QUICK SETUP N QS GAS MEASUREMENT (1004)Function No. Function name Setting to be selected ( P )(to next function with F )1004 QS GAS MEASUREMENT YESAfter F is pressed by way of confirmation, the Quick Setup menu calls upall the subsequent functions in succession.Æ6400 ASSIGN LOW FLOWCUTOFF6402 ON-VALUE LOW FLOWCUT OFF6403 OFF-VALUE LOW FLOWCUTOFFOn account of the low mass flow involved when gas flows are measured,it is advisable not to use a low flow cut off.Setting: OFFIf the ASSIGNMENT LOW FLOW CUTOFF function was not set to"OFF", the following applies:Setting: 0.0000 [unit]User input: Flow rates for gas measurements are low, so the value for theswitch-on point (= low flow cut off) must be correspondingly low.If the ASSIGNMENT LOW FLOW CUTOFF function was not set to"OFF", the following applies:Setting: 50%User input: Enter the switch-off point as a positive hysteresis in %,referenced to the switch-on point.Back to the HOME position: Press and hold down Esc key X for longer than three seconds or Repeatedly press and release Esc key X Exit the function matrix step by stepÆ!Note!Quick Setup automatically deactivates the function EMPTY PIPE DETECTION (6420) so that theinstrument can measure flow at low gas pressures.Page 70 • MN0M030Issue/Rev. 0.2 (12/12)
Proline Promass 83 Modbus RS485Commissioning6.3.5 Quick Setup "Communication"To establish serial data transfer, various arrangements between the Modbus master and Modbusslave are required which have to be taken into consideration when configuring various functions.These functions can be configured quickly and easily by means of the "Communication" QuickSetup. The following table explains the parameter configuration options in more detail.Fig. 46:Quick Setup communicationIssue/Rev. 0.2 (12/12) MN0M030 • Page 71
Page 1 and 2:
Issue/Rev. 0.2 (12/12)Coriolis Mass
Page 3 and 4:
Proline Promass 83 Modbus RS485Tabl
Page 5 and 6:
Proline Promass 83 Modbus RS485Safe
Page 7 and 8:
Proline Promass 83 Modbus RS485Iden
Page 9 and 10:
Proline Promass 83 Modbus RS485Iden
Page 12 and 13:
InstallationProline Promass 83 Modb
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21: InstallationProline Promass 83 Modb
Page 26 and 27: WiringProline Promass 83 Modbus RS4
Page 34 and 35: OperationProline Promass 83 Modbus
Page 60 and 61: EscCommissioningProline Promass 83
Page 62 and 63: CommissioningProline Promass 83 Mod
Page 64 and 65: CommissioningRecommended settings Q
Page 86 and 87: MaintenanceProline Promass 83 Modbu
Page 88 and 89: AccessoriesProline Promass 83 Modbu
Page 90 and 91: TroubleshootingProline Promass 83 M
Page 92 and 93: TroubleshootingModbus No. Device st
Page 94 and 95: TroubleshootingäProline Promass 83
Page 108 and 109: Technical dataProline Promass 83 Mo
Page 120 and 121:
Technical dataPerformance character
Page 122 and 123:
Technical dataProline Promass 83 Mo
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Technical dataLimiting flowPressure
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Proline Promass 83 Modbus RS485Inde
Page 156 and 157:
Proline Promass 83 Modbus RS485Rela
Page 158:
The specifications contained herein
show all

Proline Promass 83E/F/O Modbus RS485 Operating Instructions

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?