Proline Promass 83E/F/O Modbus RS485 Operating Instructions

More documents

Recommendations

Info

EscCommissioningProline Promass 83 Modbus RS4856.3 Quick Setup6.3.1 Quick Setup "Commissioning"In the case of measuring devices without a local display, the individual parameters and functionsmust be configured via the operating program, e.g. FieldCare.If the measuring device is equipped with a local display, all the important device parameters andadditional functions for standard operation can be configured quickly and easily by means of thefollowing Quick Setup menus.XXX.XXX.XX-+ EHOME-POSITIONBE ++ Quick Setup +EQS 1002Commission2000LanguagePre-settingmSelection system unitsMass flowVolume flowCorr. Vol. flowDensityTemperatureQuitUnit 0400Mass flowUnit 0402Volume flowUnit 0404Corr. Vol. flowUnit 0420DensityUnit 0422TemperatureUnit 3001TotalizerUnit 3001TotalizerCorr. Vol. 6460calculationReferenceDensityCalculatedUnit 0421 6462Ref. Density Exp. Coeff. Lin64616463Fix. Density Exp. Coeff. SQR6464Reference temp.YesnConfigure another system unit ?NooSelect output typeCurrent output 1 Freq./Pulse output 1Quit4200Operation ModeAssign 4000Current output4001Current span4002Value 0/4 mA4003Value 20 mA4004Meas. mode4005Time constant4006Failsafe modeFrequencyAssign 4201Freq. output4203End value freq.4204Value F Low4205Value F High4206Meas. mode4207Output signal4208Time constant4209Failsafe modePulseAssign 4221Pulse output4222Pulse value4223Pulse width4225Meas. mode4226Output signal4227Failsafe modeYespConfigure another output ?NoYesAutomatic configuration of display ?NoAutomatic parameterization of the displayqrBatchingsPulsating flowCarry out another Quick Setup ?Gas meas.CommunicationNoCarry out the selected Quick SetupFig. 41:Quick Setup "Commissioning"a0003255-enPage 60 • MN0M030Issue/Rev. 0.2 (12/12)
Proline Promass 83 Modbus RS485Commissioning! Note!• The display returns to the cell SETUP COMMISSIONING (1002) if you the press X key combination duringparameter interrogation. The stored parameters remain valid.• The "Commissioning" Quick Setup must be carried out before one of the Quick Setups explained below is run.mnThe "DELIVERY SETTING" option sets every selected unit to the factory setting.The "ACTUAL SETTING" accepts the units you configured beforehand.Only units not yet configured in m the current Setup are offered for selection in each cycle. The unit for mass,volume and corrected volume is derived from the corresponding flow unit.o The "YES" option remains visible until all the units have been configured."NO" is the only option displayed when no further units are available.pThis prompt only appears if a current output and/or pulse/frequency output is available. Only the outputs not yetconfigured in the current Setup are offered for selection in each cycle.q The "YES" option remains visible until all the outputs have been configured."NO" is the only option displayed when no further outputs are available.rThe "automatic parameterization of the display" option contains the following basic settings/factory settingsYESNOMain line = mass flowAdditional line = totalizer 1Information line = operating/system conditionThe existing (selected) settings remain.sThe execution of other Quick Setups is described in the following sections.Issue/Rev. 0.2 (12/12) MN0M030 • Page 61
Page 1 and 2:
Issue/Rev. 0.2 (12/12)Coriolis Mass
Page 3 and 4:
Proline Promass 83 Modbus RS485Tabl
Page 5 and 6:
Proline Promass 83 Modbus RS485Safe
Page 7 and 8:
Proline Promass 83 Modbus RS485Iden
Page 9 and 10: Proline Promass 83 Modbus RS485Iden
Page 12 and 13: InstallationProline Promass 83 Modb
Page 26 and 27: WiringProline Promass 83 Modbus RS4
Page 34 and 35: OperationProline Promass 83 Modbus
Page 62 and 63: CommissioningProline Promass 83 Mod
Page 64 and 65: CommissioningRecommended settings Q
Page 86 and 87: MaintenanceProline Promass 83 Modbu
Page 88 and 89: AccessoriesProline Promass 83 Modbu
Page 90 and 91: TroubleshootingProline Promass 83 M
Page 92 and 93: TroubleshootingModbus No. Device st
Page 94 and 95: TroubleshootingäProline Promass 83
Page 108 and 109: Technical dataProline Promass 83 Mo
Page 110 and 111:
Technical dataProline Promass 83 Mo
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Technical dataPerformance character
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Technical dataLimiting flowPressure
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Proline Promass 83 Modbus RS485Inde
Page 156 and 157:
Proline Promass 83 Modbus RS485Rela
Page 158:
The specifications contained herein
show all

Proline Promass 83E/F/O Modbus RS485 Operating Instructions

Create successful ePaper yourself

Delete template?

Save as template?