Proline Promass 83E/F/O Modbus RS485 Operating Instructions

More documents

Recommendations

Info

OperationProline Promass 83 Modbus RS485#Warning!"Caution!5.7.5 Relay output configurationThe relay contact can be configured as normally open (NO or make) or normally closed (NC orbreak) contacts by means of two jumpers on the pluggable submodule. This configuration can becalled up at any time with the ACTUAL STATUS RELAY function (4740).Risk of electric shock. Exposed components carry dangerous voltages. Make sure that the powersupply is switched off before you remove the cover of the electronics compartment.1. Switch off power supply.2. Remove the I/O board ä 102.3. Position the jumpers (see Figure).If you change the setting you must always change the positions of both jumpers!Note precisely the specified positions of the jumpers.4. Installation of the I/O board is the reverse of the removal procedure.Fig. 40:Configuring relay contacts (NC / NO) on the convertible I/O board (submodule) with the help of jumpers.1 Configured as NO contact (default, relay 1)2 Configured as NC contact (default, relay 2)Page 58 • MN0M030Issue/Rev. 0.2 (12/12)
Proline Promass 83 Modbus RS485Commissioning6 Commissioning6.1 Function checkMake sure that the following function checks have been performed successfully before switching onthe supply voltage for the measuring device:• Checklist for "Post-installation check" ä 25• Checklist for "Post-connection check" ä 326.2 Switching on the measuring deviceOnce the function check has been performed successfully, the device is operational and can beswitched on via the supply voltage. The device then performs internal test functions and thefollowing messages are shown on the local display:PROMASS 83START-UPRUNNINGStart-up messagePROMASS 83ÆDEVICE SOFTWAREV XX.XX.XXCurrent software versionÆModbus RS485RELAY OUTPUT 1RELAY OUTPUT 2STATUS INPUT 1List of installed input/output modulesÆSYSTEM OK OPERATIONBeginning of normal measuring modeÆ!Note!Normal measuring mode commences as soon as startup completes.Various measured-value and/or status variables (HOME position) appear on the display.If startup fails, an error message indicating the cause is displayed.Issue/Rev. 0.2 (12/12) MN0M030 • Page 59
Page 1 and 2:
Issue/Rev. 0.2 (12/12)Coriolis Mass
Page 3 and 4:
Proline Promass 83 Modbus RS485Tabl
Page 5 and 6:
Proline Promass 83 Modbus RS485Safe
Page 7 and 8: Proline Promass 83 Modbus RS485Iden
Page 9 and 10: Proline Promass 83 Modbus RS485Iden
Page 12 and 13: InstallationProline Promass 83 Modb
Page 26 and 27: WiringProline Promass 83 Modbus RS4
Page 34 and 35: OperationProline Promass 83 Modbus
Page 60 and 61: EscCommissioningProline Promass 83
Page 62 and 63: CommissioningProline Promass 83 Mod
Page 64 and 65: CommissioningRecommended settings Q
Page 86 and 87: MaintenanceProline Promass 83 Modbu
Page 88 and 89: AccessoriesProline Promass 83 Modbu
Page 90 and 91: TroubleshootingProline Promass 83 M
Page 92 and 93: TroubleshootingModbus No. Device st
Page 94 and 95: TroubleshootingäProline Promass 83
Page 108 and 109:
Technical dataProline Promass 83 Mo
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Technical dataPerformance character
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Technical dataLimiting flowPressure
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Proline Promass 83 Modbus RS485Inde
Page 156 and 157:
Proline Promass 83 Modbus RS485Rela
Page 158:
The specifications contained herein
show all

Proline Promass 83E/F/O Modbus RS485 Operating Instructions

Create successful ePaper yourself

Delete template?

Save as template?