Proline Promass 83E/F/O Modbus RS485 Operating Instructions

More documents

Recommendations

Info

OperationProline Promass 83 Modbus RS485"Caution!!Note!"Caution!5.3.1 General notesThe Quick Setup menu contains the default settings that are adequate for commissioning. Complexmeasuring operations on the other hand necessitate additional functions that you can configure asnecessary and customize to suit your process parameters. The function matrix, therefore, comprisesa multiplicity of additional functions which, for the sake of clarity, are arranged on a number ofmenu levels (blocks, groups, and function groups).Comply with the following instructions when configuring functions:• You select functions as described ä 39.Each cell in the function matrix is identified by a numerical or letter code on the display.• You can switch off certain functions (OFF). If you do so, related functions in other function groupswill no longer be displayed.• Certain functions prompt you to confirm your data entries. Press OS to select "SURE [ YES ]" andpress F to confirm. This saves your setting or starts a function, as applicable.• Return to the HOME position is automatic if no key is pressed for 5 minutes.• Programming mode is disabled automatically if you do not press a key within 60 secondsfollowing automatic return to the HOME position.All functions are described in detail, as is the function matrix itself, in the "Description of DeviceFunctions" manual, which is a separate part of these Operating Instructions.• The transmitter continues to measure while data entry is in progress, i.e. the current measuredvalues are output via the signal outputs or the fieldbus communication in the normal way.• If the supply voltage fails all preset and parameterized values remain safely stored in the EEPROM.5.3.2 Enabling the programming modeThe function matrix can be disabled. Disabling the function matrix rules out the possibility ofinadvertent changes to device functions, numerical values or factory settings. A numerical code(factory setting = 83) has to be entered before settings can be changed.If you use a code number of your choice, you exclude the possibility of unauthorized personsaccessing data ( see the "Description of Device Functions" manual).Comply with the following instructions when entering codes:• If programming is disabled and the OS operating elements are pressed in any function, a promptfor the code automatically appears on the display.• If "0" is entered as the customer's code, programming is always enabled!• The service organization can be of assistance if you mislay your personal code.Changing certain parameters such as all sensor characteristics, for example, influences numerousfunctions of the entire measuring system, particularly measuring accuracy.There is no need to change these parameters under normal circumstances and consequently, theyare protected by a special code known only to the service organization. Pleasecontact if you have any questions.5.3.3 Disabling the programming modeProgramming mode is disabled if you do not press a key within 60 seconds following automaticreturn to the HOME position.You can also disable programming in the ACCESS CODE function by entering any number (otherthan the customer's code).Page 40 • MN0M030Issue/Rev. 0.2 (12/12)
Proline Promass 83 Modbus RS485Operation5.4 Error messages5.4.1 Type of errorErrors which occur during commissioning or measuring operation are displayed immediately. If twoor more system or process errors occur, the error with the highest priority is the one shown on thedisplay.The measuring system distinguishes between two types of error:• System error: Includes all device errors, e.g. communication errors, hardware errors, etc.ä 90• Process error: Includes all application errors, e.g. fluid not homogeneous, etc. ä 96Fig. 29: Error messages on the display (example)1 Error type: P = process error, S = system error2 Error message type: $ = fault message, ! = notice message3 Error designation4 Error number5 Duration of most recent error occurrence (hours: minutes: seconds)!Note!5.4.2 Error message typeThe measuring device permanently assigns two types of error messages (fault message or noticemessage) to system errors and process errors, thereby giving them a different weighting ä 89 ff.Serious system errors, e.g. module defects, are always identified and classed as "fault messages" bythe measuring device.Notice message (!)• The error in question has no effect on the current measuring operation and the outputs of themeasuring device.• Displayed as Exclamation mark (!), type of error (S: system error, P: process error)Fault message ( $)• The error in question stops or interrupts running operation and has an immediate effect on theoutputs. The response of the outputs (failsafe mode) can be defined by means of functions in thefunction matrix ä 89.• Displayed as Lightning flash ( $ ), type of error (S: system error, P: process error)• Error conditions can be output via the relay outputs or the fieldbus communication.• If an error message occurs, an upper or lower signal level for the breakdown informationaccording to NAMUR NE 43 can be output via the current output.Issue/Rev. 0.2 (12/12) MN0M030 • Page 41
Page 1 and 2: Issue/Rev. 0.2 (12/12)Coriolis Mass
Page 3 and 4: Proline Promass 83 Modbus RS485Tabl
Page 5 and 6: Proline Promass 83 Modbus RS485Safe
Page 7 and 8: Proline Promass 83 Modbus RS485Iden
Page 9 and 10: Proline Promass 83 Modbus RS485Iden
Page 12 and 13: InstallationProline Promass 83 Modb
Page 26 and 27: WiringProline Promass 83 Modbus RS4
Page 34 and 35: OperationProline Promass 83 Modbus
Page 60 and 61: EscCommissioningProline Promass 83
Page 62 and 63: CommissioningProline Promass 83 Mod
Page 64 and 65: CommissioningRecommended settings Q
Page 86 and 87: MaintenanceProline Promass 83 Modbu
Page 88 and 89: AccessoriesProline Promass 83 Modbu
Page 90 and 91:
TroubleshootingProline Promass 83 M
Page 92 and 93:
TroubleshootingModbus No. Device st
Page 94 and 95:
TroubleshootingäProline Promass 83
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Technical dataProline Promass 83 Mo
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Technical dataPerformance character
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Technical dataLimiting flowPressure
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Proline Promass 83 Modbus RS485Inde
Page 156 and 157:
Proline Promass 83 Modbus RS485Rela
Page 158:
The specifications contained herein
show all

Proline Promass 83E/F/O Modbus RS485 Operating Instructions

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?