Proline Promass 83E/F/O Modbus RS485 Operating Instructions

More documents

Recommendations

Info

OperationProline Promass 83 Modbus RS4855.2.5 Controlling the batching processes using the local displayFilling processes can be carried out directly by means of the local display with the aid of the optional"(Batching)" software package (F–CHIP, accessories ä 87). Therefore, the device can be fullydeployed in the field as a "batch controller".Procedure:1. Configure all the required batching functions and assign the lower display info line(= BATCHING KEYS) using the "Batch" Quick Setup menu (ä 65 ) or use the functionmatrix ( ä 39).The following "softkeys" then appear on the bottom line of the local display å 27:– START = left display key (S)– PRESET = middle display key (O)– MATRIX = right display key (F)2. Press the "PRESET (O)" key. Various batching process functions requiring configuration willnow appear on the display:"PRESET" Initial settings for the batching processNo. Function Settings7200 BATCH SELECTOR OS Selection of the batching liquid (BATCH #1 to 6)7203 BATCH QUANTITY If the "ACCESS CUSTOMER" option was selected for the "PRESETbatch quantity" prompt in the "Batching" Quick Setup, the batchingquantity can be altered via the local display. If the "LOCKED" optionwas selected, the batching quantity can only be read and cannot bealtered until the private code has been entered.7265 RESET TOTAL BATCH SUM/COUNTERResets the batching quantity counter or the total batching quantity to"0".3. After exiting the PRESET menu, you can now start the batching process by pressing "START(S)". New softkeys (STOP / HOLD or GO ON) now appear on the display. You can use theseto interrupt, continue or stop the batching process at any time. å 27STOP (S) Stops batching processHOLD (O) Interrupts batching process (softkey changes to "GO ON")GO ON (O) Continues batching process (softkey changes to "HOLD")After the batch quantity is reached, the "START" or "PRESET" softkeys reappear on the display.Fig. 27:Controlling batching processes using the local display (softkeys)Page 38 • MN0M030Issue/Rev. 0.2 (12/12)
Proline Promass 83 Modbus RS485Operation!Note!5.3 Brief operating instructions to the function matrix• See the general notes ä 40• Function descriptions see the "Description of Device Functions" manual1. HOME position F Entry into the function matrix2. Select a block (e.g. OUTPUTS)3. Select a group (e.g. CURRENT OUTPUT 1)4. Select a function group (e.g. SETTINGS)5. Select a function (e.g. TIME CONSTANT)Change parameter / enter numerical values:P Select or enter enable code, parameters, numerical valuesF Save your entries6. Exit the function matrix:– Press and hold down Esc key (X) for longer than 3 seconds HOME position– Repeatedly press Esc key (X) Return step-by-step to HOME positionEsc- + ErmE–Esc+–Esc+>3so p qE E E E E E E– +– +– +++ ––n+–EEEEFig. 28:Selecting functions and configuring parameters (function matrix)a0001210Issue/Rev. 0.2 (12/12) MN0M030 • Page 39
Page 1 and 2: Issue/Rev. 0.2 (12/12)Coriolis Mass
Page 3 and 4: Proline Promass 83 Modbus RS485Tabl
Page 5 and 6: Proline Promass 83 Modbus RS485Safe
Page 7 and 8: Proline Promass 83 Modbus RS485Iden
Page 9 and 10: Proline Promass 83 Modbus RS485Iden
Page 12 and 13: InstallationProline Promass 83 Modb
Page 26 and 27: WiringProline Promass 83 Modbus RS4
Page 34 and 35: OperationProline Promass 83 Modbus
Page 60 and 61: EscCommissioningProline Promass 83
Page 62 and 63: CommissioningProline Promass 83 Mod
Page 64 and 65: CommissioningRecommended settings Q
Page 86 and 87: MaintenanceProline Promass 83 Modbu
Page 88 and 89:
AccessoriesProline Promass 83 Modbu
Page 90 and 91:
TroubleshootingProline Promass 83 M
Page 92 and 93:
TroubleshootingModbus No. Device st
Page 94 and 95:
TroubleshootingäProline Promass 83
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Technical dataProline Promass 83 Mo
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Technical dataPerformance character
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Technical dataLimiting flowPressure
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Proline Promass 83 Modbus RS485Inde
Page 156 and 157:
Proline Promass 83 Modbus RS485Rela
Page 158:
The specifications contained herein
show all

Proline Promass 83E/F/O Modbus RS485 Operating Instructions

Create successful ePaper yourself

Delete template?

Save as template?