Proline Promass 83E/F/O Modbus RS485 Operating Instructions

More documents

Recommendations

Info

WiringProline Promass 83 Modbus RS4854.5 Post-connection checkPerform the following checks after completing electrical installation of the measuring device:Device condition and specificationsNotesAre cables or the device damaged (visual inspection)? -Electrical connectionDoes the supply voltage match the specifications on the nameplate?Notes85 to 260V AC (45 to 65 Hz)20 to 55 V AC (45 to 65 Hz)16 to 62 V DCDo the cables comply with the specifications? ä 26Do the cables have adequate strain relief? -Cables correctly segregated by type?Without loops and crossovers?Are the power-supply and signal cables correctly connected?-See the wiring diagram insidethe cover of the terminalcompartmentAre all screw terminals firmly tightened? -Are all cable entries installed, firmly tightened and correctly sealed?Cables looped as "water traps"?See the "Degree of protection"section ä 31Are all housing covers installed and firmly tightened? -Fieldbus electrical connectionNotesHas each fieldbus segment been terminated at both ends with a bus terminator? ä 56Has the max. length of the fieldbus cable been observed in accordance with thespecifications?Has the max. length of the spurs been observed in accordance with thespecifications?ä 26ä 26Is the fieldbus cable fully shielded and correctly grounded? ä 27Page 32 • MN0M030Issue/Rev. 0.2 (12/12)
Proline Promass 83 Modbus RS485Operation"Caution!4.3.2 Terminal assignmentOnly certain combinations of submodules (see Table) on the I/O board are permissible. Theindividual slots are marked and assigned to the following terminals in the connection compartmentof the transmitter:• Slot "INPUT / OUTPUT 3" = Terminals 22 / 23• Slot "INPUT / OUTPUT 4" = Terminals 20 / 21Terminal No. (inputs/outputs)Order characteristicfor "inputs/outputs"20 (+) / 21 (–)Submodule onslot No. 422 (+) / 23 (–)Submodule onslot No. 324 (+) / 25 (–)Fixed onI/O board26 = B (RxD/TxD-P) 27 = A (RxD/TxD-N) Fixed on I/O boardQ – – Status input Modbus RS4857 Relay output 2 Relay output 1 Status input Modbus RS485!Note!N Current output Frequency output Status input Modbus RS485The electrical values of the inputs and outputs can be found in the "Technical data" section.4.4 Degree of protectionThe measuring device fulfill all the requirements for IP 67.Compliance with the following points is mandatory following installation in the field or servicing,in order to ensure that IP 67 protection is maintained:• The housing seals must be clean and undamaged when inserted into their grooves. The seals must be dried, cleaned or replaced if necessary.• The threaded fasteners and screw covers must be firmly tightened.• The cables used for connection must be of the specified outside diameter ä 112, cable entries.• The cable entries must be firmly tighten (point a å 23).• The cable must loop down in front of the cable entry ("water trap") (point b å 23). This arrangement prevents moisture penetrating the entry.! Note!The cable entries may not be point up.abFig. 23:Installation instructions, cable entriesa0001914"Caution!• Remove all unused cable entries and insert plugs instead.• Do not remove the grommet from the cable entry.Do not loosen the screws of the sensor housing, as otherwise the degree of protection guaranteedby no longer applies.Issue/Rev. 0.2 (12/12) MN0M030 • Page 33
Page 1 and 2: Issue/Rev. 0.2 (12/12)Coriolis Mass
Page 3 and 4: Proline Promass 83 Modbus RS485Tabl
Page 5 and 6: Proline Promass 83 Modbus RS485Safe
Page 7 and 8: Proline Promass 83 Modbus RS485Iden
Page 9 and 10: Proline Promass 83 Modbus RS485Iden
Page 12 and 13: InstallationProline Promass 83 Modb
Page 26 and 27: WiringProline Promass 83 Modbus RS4
Page 34 and 35: OperationProline Promass 83 Modbus
Page 60 and 61: EscCommissioningProline Promass 83
Page 62 and 63: CommissioningProline Promass 83 Mod
Page 64 and 65: CommissioningRecommended settings Q
Page 82 and 83:
CommissioningProline Promass 83 Mod
Page 84 and 85:
CommissioningProline Promass 83 Mod
Page 86 and 87:
MaintenanceProline Promass 83 Modbu
Page 88 and 89:
AccessoriesProline Promass 83 Modbu
Page 90 and 91:
TroubleshootingProline Promass 83 M
Page 92 and 93:
TroubleshootingModbus No. Device st
Page 94 and 95:
TroubleshootingäProline Promass 83
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Technical dataProline Promass 83 Mo
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Technical dataPerformance character
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Technical dataLimiting flowPressure
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Proline Promass 83 Modbus RS485Inde
Page 156 and 157:
Proline Promass 83 Modbus RS485Rela
Page 158:
The specifications contained herein
show all

Proline Promass 83E/F/O Modbus RS485 Operating Instructions

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?