Proline Promass 83E/F/O Modbus RS485 Operating Instructions

More documents

Recommendations

Info

InstallationProline Promass 83 Modbus RS4853.2.3 OrientationMake sure that the direction of the arrow on the nameplate of the sensor matches the direction offlow direction in which the fluid flows through the pipe.Orientation Promass AVerticalRecommended orientation with direction of flow upwards. When fluid is not flowing, entrainedsolids will sink down and gases will rise away from the measuring tube. The measuring tubes canbe completely drained and protected against solids build-up.HorizontalWhen installation is correct the transmitter housing is above or below the pipe. This means that nogas bubbles or solids deposits can form in the bent measuring tube (single-tube system)."Caution!Special installation instructions for Promass ARisk of measuring pipe fracture if sensor installed incorrectly!The sensor may not be installed in a pipe as a freely suspended sensor:• Using the base plate, mount the sensor directly on the floor, the wall or the ceiling.• Support the sensor on a firmly mounted support base (e.g. angle bracket).A0018978VerticalWe recommend two installation versions when mounting vertically:• Mounted directly on a wall using the base plate• Measuring device supported on an angle bracket mounted on the wall4 x10 mmA0018980HorizontalWe recommend the following installation version when mounting horizontally:• Measuring device standing on a firm support baseA0018979Page 16 • MN0M030Issue/Rev. 0.2 (12/12)
Proline Promass 83 Modbus RS485InstallationOrientation Promass F, E, H, I, S, P, O, XMake sure that the direction of the arrow on the nameplate of the sensor matches the direction offlow (direction in which the fluid flows through the pipe).Vertical:Recommended orientation with upward direction of flow (Fig. V). When fluid is not flowing,entrained solids will sink down and gases will rise away from the measuring tube. The measuring tubes can be completely drained and protected against solids buildup.Horizontal (Promass F, E, O):The measuring tubes of Promass F, E and O must be horizontal and beside each other. When installation is correct the transmitter housing is above or below the pipe (Fig. H1/H2).Always avoid having the transmitter housing in the same horizontal plane as the pipe.See next chapter - special installation instructions.Horizontal (Promass H, I, S, P, X):Promass H, I, S, P and X can be installed in any orientation in a horizontal pipe run.Promass H, I, S, P: See next chapter - special installation instructionsPromass F, E, OStandard, compactPromass F, EStandard, remotePromass FHigh-temperature,compactPromass FHigh-temperature,remotePromass H, I, S, PPromass XAbb. V:Vertical orientationÃÃ ÃÃ ÃÃ ÃÃ ÃÃ ÃÃa0004572Abb. H1:HorizontalorientationTransmitter head upÃÃÃÃ✘TM > 200 °C( 392 °F)ÃTM > 200 °C( 392 °F)ÃÃÃÃa0004576Abb. H2:HorizontalorientationTransmitter headdownAbb. H3:HorizontalorientationTransmitter head tothe sidea0004580A0015445ÃÃ ÃÃ ÃÃ ÃÃ ÃÃ ÃÃ✘ ✘ ✘ ✘ ÃÃ Ã mÃÃ = Recommended orientation; Ã = Orientation recommended in certain situations; ✘ = Impermissible orientationm The measuring tubes are curved. Therefore the unit is installed horizontally, adapt the sensor position to the fluidproperties:• Suitable to a limited extent for fluids with entrained solids. Risk of solids accumulating• Suitable to a limited extent for outgassing fluids. Risk of air accumulatingIn order to ensure that the permissible ambient temperature range for the transmitter (ä 133)is not exceeded, we recommend the following orientations:• For fluids with very high temperatures we recommend the horizontal orientation with thetransmitter head pointing downwards (Fig. H2) or the vertical orientation (Fig. V).• For fluids with very low temperatures, we recommend the horizontal orientation with thetransmitter head pointing upwards (Fig. H1) or the vertical orientation (Fig. V).Issue/Rev. 0.2 (12/12) MN0M030 • Page 17
Page 1 and 2: Issue/Rev. 0.2 (12/12)Coriolis Mass
Page 3 and 4: Proline Promass 83 Modbus RS485Tabl
Page 5 and 6: Proline Promass 83 Modbus RS485Safe
Page 7 and 8: Proline Promass 83 Modbus RS485Iden
Page 9 and 10: Proline Promass 83 Modbus RS485Iden
Page 12 and 13: InstallationProline Promass 83 Modb
Page 26 and 27: WiringProline Promass 83 Modbus RS4
Page 34 and 35: OperationProline Promass 83 Modbus
Page 60 and 61: EscCommissioningProline Promass 83
Page 62 and 63: CommissioningProline Promass 83 Mod
Page 64 and 65: CommissioningRecommended settings Q
Page 66 and 67:
CommissioningProline Promass 83 Mod
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
MaintenanceProline Promass 83 Modbu
Page 88 and 89:
AccessoriesProline Promass 83 Modbu
Page 90 and 91:
TroubleshootingProline Promass 83 M
Page 92 and 93:
TroubleshootingModbus No. Device st
Page 94 and 95:
TroubleshootingäProline Promass 83
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Technical dataProline Promass 83 Mo
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Technical dataPerformance character
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Technical dataLimiting flowPressure
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Proline Promass 83 Modbus RS485Inde
Page 156 and 157:
Proline Promass 83 Modbus RS485Rela
Page 158:
The specifications contained herein
show all

Proline Promass 83E/F/O Modbus RS485 Operating Instructions

Create successful ePaper yourself

Delete template?

Save as template?