Duallie Infant Car Seat Adapter Instructions - BOB Trailers and ...

INSTALL CANOPY SPACERSET PARKING BRAKE. See the “Parking Brake” section of your stroller owner’s manual.COLLAPSE HANDLE BARREMOVE EXISTING BONNET SCREWSqueeze red handles andfold handle bar forward.Use an 8mm socket wrench onlocknut and a 4mm hex wrenchon bonnet screw head.Turn socket wrench counterclockwise.Remove locknut and disassemble.REASSEMBLE CANOPYInsert new longerbonnet screw throughwasher, stroller tube,spacer, puck withcurved stay and puckwith straight stay.BonnetSpacerBonnetScrewpucksstraightcurvedAPPLY LOCTITE 262SEE WARNINGSat end of document.Apply a dropof Loctite 262 toexposed threadsof screw.ATTACH LOCKNUTUse an 8mm socket wrench onlocknut and a 4mm hex wrenchon screw head.Turn socket wrench clockwise.REPEAT STEPS3 though 6 for other side.RAISE HANDLE BARTIGHTEN FIRMLY (3.7 N.m)OMA18BP2

ATTACH MAIN BARPOSITION ARMSRotate arms into anupright position.PREPARE TO ASSEMBLERest ICSA assembly on stroller seat.Place pivot screws andpivot plugs on stroller seatnext to ICSA.INSERT PIVOT SCREWInsert a pivot screwthrough end of main barand into pivot plug......just far enough to keep thepivot plug from slipping offpivot screw.PICK UP ICSAPick up the ICSA assembly holding the pivotscrews and pivot plugs in place with hands.INSERT PIVOT PLUGSPosition ends ofmain bar overcorrespondingpivot brackets.Slip either pivotplug into openingon pivot bracketand push pivotscrew flushagainst bar.Repeat on other side.PivotBracketINSTALL PIVOT NUTTIGHTEN PIVOT NUTUse a Phillips screwdriverto tighten the pivot screwclockwise, while holding thepivot nut.REPEAT STEPS14 and 15 for other side.Reach under fabric seat.Thread pivot nut ontopivot screw as shown.OMA18BP3

ATTACH RESTRAINT BELT AND ARMSLOCATE FABRIC SCREWREMOVE FABRIC SCREWExtend canopy to exposelower fabric screw.Remove screwwith Phillipsscrewdriver,exposing fabricgrommet andrivet nut.Repeat on other side.POSITION ARM (TRAY SIDE)Position arm betweencanopy and frame.Align arm hole overfabric grommetand rivet nut.SECURE ARMInsert sharp screw through end of arm,fabric grommet and into rivet nut.Sharp screw should tighten flushagainst arm.Note:If screw doesnot turn easily,unscrew andstart again.ASSEMBLE RESTRAINT BELT M AND ARMSlide restraint belt Mgrommet over arm post.POSITION ASSEMBLYPosition arm betweencanopy and frame.Align arm hole over fabric grommetand rivet nut.Red pull ringshould face out.Arm PostOMA18BP4

INSERT SHARP SCREWHold strap at a 90degree angle.TIGHTEN SHARP SCREWTighten firmly withPhillips screwdriver.90°Insert sharp screwthrough arm, fabricgrommet and into rivet nut.Note:If screw does not turn easily,unscrew and start again.ATTACH RESTRAINT BELT FPREPARE ASSEMBLYPosition both canopiesagainst handle bar.REMOVE EXISTING FABRIC SCREWPlace restraint belt Fon stroller seat.Slip finger under fabric andplastic mount to hold nut in place.Remove lower screw withPhillips screwdriver.Note:Save screw for rightside tray installation.ATTACH RESTRAINT BELT FKeeping your finger on thenut, insert restraint beltscrew through holeand into nut.TIGHTEN SCREWTighten restraint beltscrew firmly with Phillipsscrewdriver.OMA18BP5

PREPARE STROLLER FOR INFANT CAR SEAT INSTALLATIONSET PARKINGBRAKESee the “Parking Brake”section of your strollerowner’s manual.POSITION CANOPYPosition both canopiesagainst handle bar.UNBUCKLERESTRAINT BELTUnbuckle restraintbelt. Place endsoutside seat.INSTALL INFANT CAR SEATWarningWhen installing car seat in the Duallie ICSA for the first time,test fit with the car seat unoccupied to ensure you understandthe process. Installing occupied Infant Car Seat on Duallie ICSAfor first time may result in accident, serious injury or death.Britax® Go ToBritax ®Peg Pérego® Go ToGraco® Go ToLOWER SEAT BACKRAISE HANDLEPOSITIONCAR SEATLower seat back 7” to 8”.See the “Reclining Seat” sectionof your stroller owner’s manual.Move car seathandle into uprightcarrying position.Place car seat“rear facing” ontoICSA accessorybar, in a straightdownwardmotion.ENGAGE CAR SEATSlide grooves on undersideof car seat onto ICSAaccessory bar.SET CAR SEATGently pull canopystays while pushingcar seat handle.Car seat should“set” down ontoseat of stroller.FASTEN RESTRAINTBELTFasten restraint belt over topof infant car seat as shown.PULLPUSHOMA18BP6

TIGHTEN RESTRAINT BELTPull on red ring to tighten.WarningBe sure restraint belt tensionis not constricting child as itmay cause serious injury.DOUBLE CHECK CAR SEAT ISSECURELY ATTACHEDPull car seat upward withoutremoving restraint belt.You should not be able toremove car seat withoutunfastening restraint belt.WarningFailure to securely attach car seatmay result in serious injury or death.TO REMOVE Britax® Go ToPeg Pérego ®RAISE SEAT BACKSee the “Reclining Seat”section of your strollerowner’s manual.POSITION HANDLEMove car seat handleinto upright carryingposition.POSITION CAR SEATPlace car seat“rear facing”onto ICSAaccessory bar,in a straightdownwardmotion.ENGAGE CAR SEATSlide grooves onunderside of car seat ontoICSA accessory bar.SET CAR SEATGently pull canopy stays whilepushing car seat handle.Car seat should “set” down ontoseat of stroller.FASTEN RESTRAINT BELTFasten restraint belt over topof infant car seat as shown.PULLPUSHOMA18BP7

TIGHTEN RESTRAINT BELTPull on red ring to tighten.WarningBe sure restraintbelt tension is notconstricting child as itmay cause serious injury.DOUBLE CHECK CAR SEAT ISSECURELY ATTACHEDPull car seat upward withoutremoving restraint belt.You should not be able to removecar seat without unfasteningrestraint belt.WarningFailure to securely attach car seatmay result in serious injury or death.TO REMOVE Peg Pérego® Go ToGraco®RAISE SEAT BACKSee the “Reclining Seat”section of your strollerowner’s manual.REMOVE ACCESSORY BARUsing a Phillips screwdriver,remove both screws.TIP: Attach screws toaccessory bar for future use.CAUTION: Ends of accessory bar are sharp!POSITION HANDLEMove car seat handle intoupright carrying position.POSITION CAR SEATPlace car seat “rear facing”onto ICSA main bar, in astraight downward motion.OMA18BP8

ENGAGE CAR SEATSlide grooves on underside ofcar seat onto ICSA main bar.FASTEN RESTRAINT BELTFasten restraint belt over top ofinfant car seat as shown.Red hook on Graco®should be undermain bar.TIGHTEN RESTRAINT BELTPull on red ring to tighten.WarningBe sure restraintbelt tension is notconstricting child as itmay cause serious injury.DOUBLE CHECK CAR SEAT ISSECURELY ATTACHEDPull car seat upward withoutremoving restraint belt.You should not be able to removecar seat without unfasteningrestraint belt.WarningFailure to securely attach car seatmay result in serious injury or death.TO REMOVE Graco® Go ToTO REMOVE CAR SEATSET PARKING BRAKESee the “Parking Brake” section ofyour stroller owner’s manual.UNFASTEN RESTRAINT BELTUnfasten restraint belt.Place ends outside seat.Britax®Peg Pérego®With car seat handlein upright position,lift car seat straightup and off ICSA bar.Graco®With car seat handlein upright position,squeeze red releasebutton under Graco®car seat canopy, liftcar seat straight upand off ICSA bar.FASTEN RESTRAINT BELTFasten restraint beltwhen not in use.OMA18BP9

RIGHT TRAY INSTALLATIONWarningChildren should not beplaced directly in theBOB Stroller seat with theDuallie ICSA installed,unless tray is installeddirectly in front of child forsafety and protection.REMOVE ACCESSORY BARUsing a Phillips screwdriverremove both screws.TIP: Attach screws toaccessory bar for future use.CAUTION: Ends of accessory bar are sharp!REMOVE LONG SCREWSREMOVE SHORT SCREW AND NUTUsing a Phillipsscrewdriver, remove3 long screws fromright tray.Using a Phillips screwdriver and an 8 mmsocket wrench, remove short screw and nut.63POSITION TRAYATTACH LONG SCREWSPosition right tray on mainbar, lining up holes.Insert long screw through each hole in right tray,main bar and into nut on underside of right tray.Tighten firmly with Phillips screwdriver.ATTACH SHORT SCREW AND NUTReach under left tray andpress nut into hole.Tighten firmly withPhillips screwdriver.Reach under right tray and insertshort screw through right tray,left tray and into nut.OMA18BP10

REMOVE RESTRAINT BELTREMOVE RESTRAINT BELT FRetrieve original screw andplace on stroller seat.Keeping yourfinger on the nut,remove restraintbelt screw withPhillips screwdriver.REPLACE ORIGINAL SCREWInsert original screwthrough hole and nut.Tighten firmly.REMOVE SHARP SCREWMOVE ARM FORWARDREMOVE RESTRAINTBELT MRemove restraintbelt M from post.Remove right sidesharp screw fromright side arm.POSITION ARMRotate arm so endof arm aligns withrivet nut.REPLACE SHARPSCREWInsert sharp screwthrough end of arm,fabric grommet andinto rivet nut.TIGHTEN SHARP SCREWTighten firmly with Phillipsscrewdriver.Sharp screw should tighten flushagainst arm.Note: If screw does not turn easily,unscrew and start again.OMA18BP11

Duallie Infant Car Seat Adapter Warnings• The BOB Duallie Infant Car Seat Adapteris designed for use with double seat BOBStrollers and compatible Infant Car Seats. Thisproduct is not a universal adapter. Do not usewith car seats and stroller models other thanthose specifically listed in the Stroller and CarSeat Compatibility charts listed on page 1.• Children should not be placed directly inthe BOB Stroller seat with the Duallie ICSAinstalled, unless tray is installed directly infront of child for safety and protection.• The Duallie ICSA Restraint Belt can interferewith the accessibility and proper function ofthe right side safety harness system and theAccessory Bar of the Duallie ICSA can interferewith accessibility to the right seat. DuallieICSA restraint belt and accessory bar must beremoved from the BOB Stroller and Right Traymust be installed prior to placing child directlyin right seat. Failure to do so may result inserious injury or death.• Read and understand all owner’s manuals andwarnings for all BOB products used with theDuallie ICSA before use.• Read and understand infant car seat owner’smanual before use.• Always use seat harness of Infant Car Seat toavoid children falling out of stroller.• Maximum capacity 17.5lb (weight of infantincluding clothing). Exceeding capacity maycause stroller to become unstable.• Follow assembly instructions. Failure toproperly install this accessory productmay result in accidents, severe injury ordeath. If you are not sure you can install thisaccessory, contact your BOB retailer andarrange for them to perform the installation.• Never leave children unattended in thestroller/infant car seat.• Always secure the infant car seat with therestraint belt when the car seat is placed inthe stroller. Failure to do so may result inserious injury or death.• Always keep your Infant Car Seat handlein the vertical and locked position while instroller, as extra protection for your child.• Stroller may become unstable if parcel bagsare incorrectly attached or if bags other thanthose recommended by BOB Trailers, Inc. areused.• Do not run or jog when using the DuallieICSA with car seat installed. Doing so mayresult in serious injury or death.• Do not use off-road or on uneven terrainwhen using the Duallie ICSA with car seatinstalled. Doing so may cause stroller tobecome unstable and result in accident,serious injury or death.• Children develop at different rates. Consultwith your pediatrician regarding thesuitability of the stroller use with your child.• Loctite 262 is a potentially hazardous chemical. Do not allow contact with skin oreyes. Do not ingest. Use in well ventilated area. Keep out of reach of children anddispose of vial properly. Other safety warnings for Loctite 262 can be found atwww.loctite.comBOB IS NOT RESPONSIBLE FOR INJURY, DAMAGE OR FAILURE THAT RESULTSFROM OWNERS FAULTY ASSEMBLY OR MAINTENANCE AFTER SHIPPING.OMA18BP12

BOB is a company that produces highquality products designed to promotea healthy outdoor life-style. Go towww.bobgear.com for our completeline of products. Before attemptingto assemble or use your new DuallieICSA, read and understand theseinstructions completely to insureproper assembly and operation.If you are unclear on any point, contactyour dealer, place of purchase or BOB[toll free 1-800-893-2447] before use.A list of dealers is listed on our website[www.bobgear.com]. For updates tothis manual, our warranty and for otherrecent product notifications, please visitwww.bobgear.com periodically.B.O.B, B.O.B Logo, and BOB are proprietarytrademarks of BOB Trailers, Inc.Britax® and Companion® are registeredtrademarks of Britax Excelsior Ltd. andrelated companies.Graco® Snug Ride and SafeSeat areregistered and proprietary trademarks ofGraco Children’s Products, Inc.Peg Pérego® Primo Viaggio and PrimoViaggio SIP are registered and proprietarytrademarks of Peg Pérego S.P.A. Corporation.LIMITED WARRANTYBOB Trailers Inc. takes pride in its workmanship and strives to manufacture the best productspossible. Therefore, we warranty the Duallie ICSA against defects in material and workmanshipsubject to the conditions listed below. Since no product is indestructible, it does not cover defectsattributable to or resulting from normal wear, abuse or alteration.• The Duallie ICSA iswarranted for oneyear from the date oforiginal purchase.• Warranty is onlyvalid for the originalpurchaser.• Proof of purchase isrequired to exercisethis warranty.• Labor and freightcharges are not included.• Normal wear, neglect,abuse, accidents, andimproper use are notcovered by this warranty.• Warranty claims mustbe made through anauthorized dealer.• This warranty is limited to therepair or replacement of thedefective part. BOB Trailers,Inc. shall in no event beresponsible for consequentialor special damages.• This Limited Warranty isthe only express or impliedwarranty applicable to BOBTrailers, Inc. Any impliedwarranties, includingwarranties of merchantabilityand fitness shall be limitedin scope and duration inaccordance with this limitedwarranty.OMA18BP13