iSR6200 Intelligent Storage Router Installation Guide - QLogic

More documents

Recommendations

Info

7–Removal and ReplacementPower and Cooling ModulesInstalling the Replacement PCMTo install a replacement PCM in the <strong>iSR6200</strong> chassis:1. Before you insert the new PCM into the chassis, unlatch the lever on thenew PCM (see Figure 7-11.)Figure 7-11. Unlatching Lever on New PCM2. Insert the replacement PCM into the <strong>iSR6200</strong> chassis. As shown inFigure 7-10, push the PCM straight into the chassis (1), and then make surethe PCM is properly seated into the chassis mid-plane by pushing the leverup and locking the latch in the up position (2). The PCM fans turn on and theLED should show an amber color.(1)(2)Figure 7-12. Inserting the Replacement PCM7-12 ISR651101-00 G
7–Removal and ReplacementPower and Cooling Modules3. Connect the power cable to the newly inserted PCM. Its status LED colorshould change from amber to green within five seconds.Figure 7-13. Back Side of Two PCMs, Both With Good Status Indicators4. Verify that the airflow through both PCMs is in the same direction.ISR651101-00 G 7-13
Page 1 and 2:
iSR6200Intelligent Storage RouterIn
Page 3 and 4:
Table of ContentsPrefaceIntended Au
Page 5 and 6:
iSR6200 Intelligent Storage RouterI
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
PrefaceThis user’s guide describe
Page 13 and 14:
PrefaceDocumentation Conventions•
Page 15 and 16:
PrefaceCommunications StatementsFed
Page 17 and 18:
PrefaceLaser Safety InformationVCCI
Page 19 and 20:
PrefaceTechnical SupportContact Inf
Page 21 and 22:
1 IntroductionThis chapter illustra
Page 23 and 24:
1-IntroductionPower and Cooling Mod
Page 25 and 26:
1-IntroductioniSR6200 Router Blades
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
2 PlanningDevicesThis chapter descr
Page 37 and 38:
2-PlanningiSCSI PerformanceBandwidt
Page 39 and 40:
2-PlanningPerformance TuningTable 2
Page 41 and 42:
2-PlanningHigh AvailabilityHigh Ava
Page 43 and 44:
3 InstallationThis chapter describe
Page 45 and 46:
3-InstallationInstalling the iSR620
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
3-InstallationInstalling New Firmwa
Page 59 and 60:
3-InstallationInstalling New Firmwa
Page 61 and 62:
4 ConfigurationThis chapter describ
Page 63 and 64:
4-ConfigurationEnabling Virtual Por
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
4-ConfigurationZoning Virtual Port
Page 71 and 72:
4-ConfigurationZoning Virtual Port
Page 73 and 74:
4-ConfigurationConfiguring Fibre Ch
Page 75 and 76: 4-ConfigurationConfiguring Fibre Ch
Page 77 and 78: 4-ConfigurationConnecting iSCSI Hos
Page 83 and 84: 4-ConfigurationControlling per-Host
Page 91 and 92: 5 Fibre Channel over IPFibre Channe
Page 93 and 94: 5-Fibre Channel over IPConfiguring
Page 111 and 112: 6 Diagnostics andTroubleshootingDia
Page 113 and 114: 6-Diagnostics and TroubleshootingLE
Page 115 and 116: 7 Removal and ReplacementThis chapt
Page 117 and 118: 7-Removal and ReplacementiSR6200 Ch
Page 125: 7-Removal and ReplacementPower and
Page 129 and 130: ATechnical SpecificationsThis appen
Page 131 and 132: A-Technical SpecificationsiSCSI Ini
Page 133 and 134: A-Technical SpecificationsEnvironme
Page 135 and 136: BSimple NetworkManagement ProtocolS
Page 137 and 138: B-Simple Network Management Protoco
Page 161 and 162: CLog MessagesThis appendix provides
Page 163 and 164: C-Log MessagesTable C-1. iSR6200 Ro
Page 177 and 178:
C-Log MessagesTable C-1. iSR6200 Ro
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Glossaryactivity LEDA port LED that
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
IndexAAC power 3-7activity LEDdefin
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 218:
Corporate Headquarters QLogic Corpo
show all

iSR6200 Intelligent Storage Router Installation Guide - QLogic

Create successful ePaper yourself

Delete template?

Save as template?