iSR6200 Intelligent Storage Router Installation Guide - QLogic

More documents

Recommendations

Info

6–Diagnostics and TroubleshootingRecovering a RouterIf the system fault LED shows the over-temperature blink pattern, follow thesesteps:• Inspect the chassis air vents. Are the intake and exhaust vents clear? Yes—Continue.No—Remove any debris from the fan intake and exhaust if necessary.If the condition remains, continue.• Consider the ambient air temperature near the router and clearance aroundthe router. Make necessary corrections. If the condition remains, open acommand line window and log on to the router. Enter the shutdowncommand, and then power down the router. Contact your authorizedmaintenance provider.Recovering a RouterYou may have to recover a router for one of the following reasons:• The password was changed and has been forgotten.• The router’s management IP address is unknown.To recover the router’s password, reset the password to the default by using themaintenance button (see page 1-8).You can recover the router’s IP address using either of the following methods:• Connect to the serial console port (see page 1-13), and then use the CLIset mgmt command to reconfigure the management port (see theiSR6200 CLI User’s Guide).• Use the maintenance button to reset the management port’s IP to the factorydefault of 10.0.0.1 (see page 1-8).6-4 ISR651101-00 G
7 Removal and ReplacementThis chapter describes how to remove and replace the following FRUs:• SFP Transceivers• iSR6200 Chassis Blades• “Power and Cooling Modules” on page 7-10SFP TransceiversYou can remove and replace the SFP transceivers while the iSR6200 router isoperating without damaging the router or the transceiver. However, this interruptstransmission on the affected port until you install the transceiver.• To remove a transceiver, gently press the transceiver into the port to releasethe tension, pull the release tab or lever, and then remove the transceiver.Different transceiver manufacturers have different release mechanisms.Consult the documentation for your transceiver.• To install a transceiver, insert it into the port and gently press until it snapsinto place.NOTE:The SFP transceiver fits only one way. If the SFP does not install undergentle pressure, flip it over and try again.iSR6200 Chassis BladesThe iSR6200 router provides an enhanced feature you can use to replace anyblade in the field. In a dual-blade chassis, the iSR6200 automatically restores areplacement blade’s configuration. When replacing a blade in a single-bladechassis, you can use the iSR6200 router’s management tools to save and restorea blade’s configuration.ISR651101-00 G 7-1
Page 1 and 2:
iSR6200Intelligent Storage RouterIn
Page 3 and 4:
Table of ContentsPrefaceIntended Au
Page 5 and 6:
iSR6200 Intelligent Storage RouterI
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
PrefaceThis user’s guide describe
Page 13 and 14:
PrefaceDocumentation Conventions•
Page 15 and 16:
PrefaceCommunications StatementsFed
Page 17 and 18:
PrefaceLaser Safety InformationVCCI
Page 19 and 20:
PrefaceTechnical SupportContact Inf
Page 21 and 22:
1 IntroductionThis chapter illustra
Page 23 and 24:
1-IntroductionPower and Cooling Mod
Page 25 and 26:
1-IntroductioniSR6200 Router Blades
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
2 PlanningDevicesThis chapter descr
Page 37 and 38:
2-PlanningiSCSI PerformanceBandwidt
Page 39 and 40:
2-PlanningPerformance TuningTable 2
Page 41 and 42:
2-PlanningHigh AvailabilityHigh Ava
Page 43 and 44:
3 InstallationThis chapter describe
Page 45 and 46:
3-InstallationInstalling the iSR620
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
3-InstallationInstalling New Firmwa
Page 59 and 60:
3-InstallationInstalling New Firmwa
Page 61 and 62:
4 ConfigurationThis chapter describ
Page 63 and 64: 4-ConfigurationEnabling Virtual Por
Page 69 and 70: 4-ConfigurationZoning Virtual Port
Page 71 and 72: 4-ConfigurationZoning Virtual Port
Page 73 and 74: 4-ConfigurationConfiguring Fibre Ch
Page 75 and 76: 4-ConfigurationConfiguring Fibre Ch
Page 77 and 78: 4-ConfigurationConnecting iSCSI Hos
Page 83 and 84: 4-ConfigurationControlling per-Host
Page 91 and 92: 5 Fibre Channel over IPFibre Channe
Page 93 and 94: 5-Fibre Channel over IPConfiguring
Page 111 and 112: 6 Diagnostics andTroubleshootingDia
Page 113: 6-Diagnostics and TroubleshootingLE
Page 117 and 118: 7-Removal and ReplacementiSR6200 Ch
Page 125 and 126: 7-Removal and ReplacementPower and
Page 127 and 128: 7-Removal and ReplacementPower and
Page 129 and 130: ATechnical SpecificationsThis appen
Page 131 and 132: A-Technical SpecificationsiSCSI Ini
Page 133 and 134: A-Technical SpecificationsEnvironme
Page 135 and 136: BSimple NetworkManagement ProtocolS
Page 137 and 138: B-Simple Network Management Protoco
Page 161 and 162: CLog MessagesThis appendix provides
Page 163 and 164: C-Log MessagesTable C-1. iSR6200 Ro
Page 165 and 166:
C-Log MessagesTable C-1. iSR6200 Ro
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Glossaryactivity LEDA port LED that
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
IndexAAC power 3-7activity LEDdefin
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 218:
Corporate Headquarters QLogic Corpo
show all

iSR6200 Intelligent Storage Router Installation Guide - QLogic

Create successful ePaper yourself

Delete template?

Save as template?