microwave assemblies, systems and technologies - Aptecelectronics ...

MICROWAVE ASSEMBLIES,SYSTEMS ANDTECHNOLOGIESISO 9001REGISTERED COMPANY• PIN Switches• Broadband Power Dividers• 3 dB Hybrids• Analog PIN Attenuators• Phase Shifters• Modulators• Couplers• Limiters• Custom Integrated Assemblies

TABLE OF CONTENTSCONTENTSPAGEPIN SWITCHESSingle-Pole, Single-Throw 3Single-Pole, Double-Throw 4Single-Pole, Three-Throw 5Single-Pole, Four-Throw 6Single-Pole, Five-Throw 7Single-Pole, Six-Throw 8Single-Pole, Seven-Throw 9Outline Drawings 103 dB HYBRIDS 12BROADBAND POWER DIVIDERS 13ANALOG PIN ATTENUATORS 15PHASE SHIFTERS 18MODULATORS 19COUPLERS 22LIMITERS 23CUSTOM INTEGRATED ASSEMBLIESThree-Channel Receiver Assembly 25S-Band to X-, Ku-Band Upconverter Module 26X-, Ku-Band to S-Band Downconverter Module 26Quadrature IF Mixer 26AGC Module 263–21 GHz Three-Channel Downconverter 27Miniature Downconverter 29Tri-Band Downconverter 31Two Channel, Single LO Input Downconverter 332.8–9.9 GHz Frequency Multiplexer 347.9–14.9 GHz Frequency Multiplexer 377.6–21.2 GHz Frequency Multiplexer 39Transmit Switched Multiplexer 41Transmit/Receive Switch/Amplifier 43Amplifier/Switch Assembly 44Miniature Calibration Switch 45Switchable Filter Bank 4614.5 GHz Oscillator 47X-Band Leveler 48FAX BACK PAGESPIN Switches 493 dB hybrids 50Broadband Power Dividers 51Analog PIN Attenuators 52Phase Shifters 53Modulators 54Couplers 55Limiters 56ORDERING INFORMATION 57WARRANTY 58

SINGLE-POLESWITCHESSWITCHESMITEQ offers a broad line of switchescovering multioctave bands from 0.2 to 18GHz. Single-pole, single-throw throughsingle-pole, seven-throw switches areavailable as standard products. We can, onspecial request, provide switches up tosingle-pole, twelve-throw and can arrayswitches to form switch matrices to handlesignal routing in complex systems.Custom switches up to 40 GHz are alsoavailable. Our switches can be screened tothe salient characteristics of MIL-STD-883and we offer a variety of connector optionsincluding GPO and SMA. Custom highpowerswitches capable of switching up to10 watts are also available.Our standard products achieve switchingtimes as low as two nanoseconds for thoseapplications requiring the ultimate inswitching speed. We are able to accommodatespecial video leakage needs byincorporating video filters and pulse-shapingnetworks as needed.GENERAL SPECIFICATIONSPower handling (full performance) ...... 20 dBmPower handling (no damage)................ 30 dBmVideo leakage for “F” model(RMS power) .......................................... < -50 dBm (> 2 GHz) typicalThird order input intercept point.......... 35 dBm typicalENVIRONMENTAL CONDITIONSOperating temperature .......................... 0 to 70°CStorage temperature.............................. -30 to +85°CHumidity.................................................. 95% noncondensingVibration ................................................ 12 Gs RMS, 20–2000 Hzper MIL-STD-810B,Method 514, Procedure 52

FEATURES• Multioctave bands 0.2 to 18 GHz• Current and TTL control• Low loss• High isolation• Medium and high speed models• Drop-in models• 2 ns modelsSINGLE-POLE SINGLE-THROW SWITCHESFrequency Insertion Type DC Power ConsumptionRange Model Loss Isolation *VSWR (Reflective/ Pos. Supply Neg. Supply Ordering Additional(GHz) Number (dB, Max.) (dB, Min.) (Max.) Absorptive) (mA, Max.) (mA, Min.) Outline Options FeaturesSTANDARD, MULTIOCTAVE BAND MODELSS103A 1.5 50 1.6:1 Ref 35 35 SPST 1-5 –0.2–2S103B 1.7 70 1.6:1 Ref 35 35 SPST 1-5 –N103A 1.6 55 1.6:1 Abs 35 35 SPST 1-5 –N103B 1.8 75 1.6:1 Abs 35 35 SPST 1-5 –S113A 1.3 60 1.6:1 Ref 35 35 SPST 1-6 –0.5–2S113B 1.5 80 1.6:1 Ref 35 35 SPST 1-6 –N113A 1.5 55 1.6:1 Abs 35 35 SPST 1-5 –N113B 1.7 75 1.6:1 Abs 35 35 SPST 1-5 –S136A 1.8 60 1.7:1 Ref 35 35 SPST 1-6 –2–8 S136B 2 80 1.7:1 Ref 35 35 SPST 1-6 –N136A 2 55 1.7:1 Abs 35 35 SPST 1-5 –N136B 2.2 70 1.7:1 Abs 35 35 SPST 1-5 –S147A 2 70 1.7:1 Ref 35 35 SPST 1-6 –4–12S147B 2.2 90 1.7:1 Ref 35 35 SPST 1-6 –N147A 2.3 50 1.7:1 Abs 35 35 SPST 1-5 –N147B 2.6 65 1.7:1 Abs 35 35 SPST 1-5 –S138A 2.6 60 2:1 Ref 35 35 SPST 1-6 –2–18S138B 3 80 2:1 Ref 35 35 SPST 1-6 –N138A 2.6 45 2:1 Abs 35 35 SPST 1-5 –N138B 3 60 2:1 Abs 35 35 SPST 1-5 –S128A 2.7 50 2:1 Ref 35 35 SPST 1-5 –1–18S128B 3 70 2:1 Ref 35 35 SPST 1-5 –N128A 2.8 45 2:1 Abs 35 35 SPST 1-5 –N128B 3.2 60 2:1 Abs 35 35 SPST 1-5 –Electrical performance of multioctave models can be optimized over narrower bandwidths, or for a particular parameter. Electrical options include: Lowerinsertion loss, lower VSWR, higher isolation, flat amplitude response, amplitude tracking. Mechanical/Control options include: Custom packaging, singlesupply operation, fast switching time, single TTL control line. Examples of custom models previously shipped are shown below. Consult factory for options.OPTIMIZED PERFORMANCE MODELS0.21–0.23 124794 1.8 80 1.6:1 Abs 35 35 SPST 5V,-12V.0.5–2 126152 1.1 60 1.6:1 Abs 70 70 Contact factory 5V,-15V. 40ns switch speed3–3.4 124516 1 60 1.5:1 Abs – – SPST 5V,-5V. 6ns rise/fall time5–5.6 125473 1.3 60 1.5:1 Abs – – SPST 5V,-5V. 6ns rise/fall time3–9 123296 1.7 60 1.7:1 Ref – – SPST 5V,-15V. 30ns switch speed9.5–10.5 127922 2.5 70 1.7:1 Abs 35 35 SPST 5V,-15V. 5ns rise/fall time2–18 124796 3.2 80 2:1 Ref – – SPST 5, -15V. 2ns rise/fall time2–18 123297 2.8 70 1.8:1 Ref 50 50 Contact factory ±15V. 4ns rise/fall time2–18 122791 3 80 1.8:1 Ref 50 50 Contact factory 5V,-12V. 3ns rise/fall time2–18 123797 2.8 70 1.8:1 Ref 50 50 Contact factory 5V,-15V. 4ns rise/fall time*For reflective models, VSWR is not specified in the “OFF” state.For absorptive models, VSWR in the “OFF” state is defined for port J2 only.3

FEATURES• Multioctave bands 0.2 to 18 GHz• Current and TTL control• Low loss• High isolation• Medium and high speed models• Drop-in models• Amplitude and phase trackingSINGLE-POLE DOUBLE-THROW SWITCHESFrequency Insertion Type DC Power ConsumptionRange Model Loss Isolation *VSWR (Reflective/ Pos. Supply Neg. Supply Ordering Additional(GHz) Number (dB, Max.) (dB, Min.) (Max.) Absorptive) (mA, Max.) (mA, Min.) Outline Options FeaturesSTANDARD, MULTIOCTAVE BAND MODELSS203A 1.2 50 1.6:1 Ref 60 60 SP2T 1-5 –0.2–2S203B 1.5 70 1.6:1 Ref 60 60 SP2T 1-5 –N203A 1.7 55 1.6:1 Abs 60 60 SP2T 1-5 –N203B 2 75 1.6:1 Abs 60 60 SP2T 1-5 –S213A 1 60 1.6:1 Ref 60 60 SP2T 1-5 –0.5–2S213B 1.3 80 1.6:1 Ref 60 60 SP2T 1-5 –N213A 1.5 55 1.6:1 Abs 60 60 SP2T 1-5 –N213B 1.8 75 1.6:1 Abs 60 60 SP2T 1-5 –S236A 1.6 60 1.7:1 Ref 60 60 SP2T 1-5 –2–8 S236B 1.8 80 1.7:1 Ref 60 60 SP2T 1-5 –N236A 1.8 55 1.7:1 Abs 60 60 SP2T 1-5 –N236B 2 70 1.7:1 Abs 60 60 SP2T 1-5 –S247A 2 70 1.7:1 Ref 60 60 SP2T 1-5 –4–12S247B 2.2 90 1.7:1 Ref 60 60 SP2T 1-5 –N247A 2 50 1.7:1 Abs 60 60 SP2T 1-5 –N247B 2.2 65 1.7:1 Abs 60 60 SP2T 1-5 –S238A 2.5 60 2:1 Ref 60 60 SP2T 1-5 –2–18S238B 2.8 80 2:1 Ref 60 60 SP2T 1-5 –N238A 2.6 45 2:1 Abs 60 60 SP2T 1-5 –N238B 3 60 2:1 Abs 60 60 SP2T 1-5 –S228A 2.6 55 2:1 Ref 60 60 SP2T 1-5 –1–18S228B 3 70 2:1 Ref 60 60 SP2T 1-5 –N228A 2.8 45 2:1 Abs 60 60 SP2T 1-5 –N228B 3.2 60 2:1 Abs 60 60 SP2T 1-5 –Electrical performance of multioctave models can be optimized over narrower bandwidths, or for a particular parameter. Electrical options include: Lowerinsertion loss, lower VSWR, higher isolation, flat amplitude response, amplitude tracking. Mechanical/Control options include: Custom packaging, singlesupply operation, fast switching time, single TTL control line. Examples of custom models previously shipped are shown below. Consult factory for options.OPTIMIZED PERFORMANCE MODELS0.5–2 124513 1.4 70 1.5:1 Ref – – SP2T 50ns switch speed0.5–2 126157 1.5 70 1.6:1 Abs 95 95 Contact factory 5V,-12V. 50ns switch speed1–2 126158 1.5 70 1.5:1 Ref 90 90 Contact factory 5V,-12V. Single TTL line1.2–1.6 122797 2.2 75 1.6:1 Abs 60 60 SP2T 5V,-15V. 50ns switch speed0.8–4 126150 1.5 70 1.7:1 Ref 60 60 SP2T 5V,-12V8–10 122499 2 60 1.6:1 Ref – – SP2T 5V,-12V. 50ns switch speed9–11 126154 2.5 40 1.5:1 Ref 25 – Contact factory Single 5V supply15–17 125963 3 45 2:1 Ref 60 60 SP2T 5V,-12V. 50ns switch speed2–18 124080 2.7 65 2:1 Ref 60 60 SP2T 5V,-12V. 50ns switch speed2–18 124784 3 65 2:1 Abs 60 60 SP2T 5V,-12V. Single TTL line2–18 127070 2.5 70 1.7:1 Abs 60 60 SP2T 5V,-15V23.5–24.5 120612 3 35 2:1 Ref – – SP2T 5V,-12V. 7ns rise/fall time*For reflective models, VSWR is not specified in the “OFF” state.For absorptive models, VSWR in the “OFF” state is defined for port J2 only.4

FEATURES• Multioctave bands 0.2 to 18 GHz• Current and TTL control• Low loss• High isolation• Medium and high speed models• Drop-in models• Amplitude and phase tracking• Binary decoded logicSINGLE-POLE THREE-THROW SWITCHESFrequency Insertion Type DC Power ConsumptionRange Model Loss Isolation *VSWR (Reflective/ Pos. Supply Neg. Supply Ordering Additional(GHz) Number (dB, Max.) (dB, Min.) (Max.) Absorptive) (mA, Max.) (mA, Min.) Outline Options FeaturesSTANDARD, MULTIOCTAVE BAND MODELSS303A 1.3 50 1.6:1 Ref 85 85 SP3T 1-5 –0.2–2S303B 1.6 70 1.6:1 Ref 85 85 SP3T 1-5 –N303A 1.7 55 1.6:1 Abs 85 85 SP3T 1-5 –N303B 2 75 1.6:1 Abs 85 85 SP3T 1-5 –S313A 1.2 60 1.6:1 Ref 85 85 SP3T 1-5 –0.5–2S313B 1.5 80 1.6:1 Ref 85 85 SP3T 1-5 –N313A 1.6 55 1.6:1 Abs 85 85 SP3T 1-5 –N313B 1.9 75 1.6:1 Abs 85 85 SP3T 1-5 –S336A 1.7 60 1.7:1 Ref 85 85 SP3T 1-5 –2–8 S336B 1.9 80 1.7:1 Ref 85 85 SP3T 1-5 –N336A 1.9 55 1.7:1 Abs 85 85 SP3T 1-5 –N336B 2.1 70 1.7:1 Abs 85 85 SP3T 1-5 –S347A 2.2 70 1.7:1 Ref 85 85 SP3T 1-5 –4–12S347B 2.4 90 1.7:1 Ref 85 85 SP3T 1-5 –N347A 2.2 50 1.7:1 Abs 85 85 SP3T 1-5 –N347B 2.5 65 1.7:1 Abs 85 85 SP3T 1-5 –S338A 2.7 60 2:1 Ref 85 85 SP3T 1-5 –2–18S338B 3 80 2:1 Ref 85 85 SP3T 1-5 –N338A 2.8 45 2:1 Abs 85 85 SP3T 1-5 –N338B 3.2 60 2:1 Abs 85 85 SP3T 1-5 –S328A 2.8 55 2:1 Ref 85 85 SP3T 1-5 –1–18S328B 3.1 70 2:1 Ref 85 85 SP3T 1-5 –N328A 2.9 45 2:1 Abs 85 85 SP3T 1-5 –N328B 3.4 60 2:1 Abs 85 85 SP3T 1-5 –Electrical performance of multioctave models can be optimized over narrower bandwidths, or for a particular parameter. Electrical options include: Lowerinsertion loss, lower VSWR, higher isolation, flat amplitude response, amplitude tracking. Mechanical/Control options include: Custom packaging, singlesupply operation, fast switching time, single TTL control line. Examples of custom models previously shipped are shown below. Consult factory for options.OPTIMIZED PERFORMANCE MODELS4.8–7.6 126145 3 60 1.5:1 Ref – – SP3T Single 5V supply5.8–14.5 126144 3 60 1.6:1 Ref – – Contact factory Single 5V supply2–12 120608 2.2 70 1.7:1 Ref 85 85 SP3T 5V,-12V2–18 124081 2.7 70 2:1 Ref – – SP3T 5V,-12V. 50ns switch speed*For reflective models, VSWR is not specified in the “OFF” state.For absorptive models, VSWR in the “OFF” state is defined for port J2 only.5

FEATURES• Multioctave bands 0.2 to 18 GHz• Current and TTL control• Low loss• High isolation• Medium and high speed models• Drop-in models• Amplitude and phase tracking• Binary decoded logicSINGLE-POLE FOUR-THROW SWITCHESFrequency Insertion Type DC Power ConsumptionRange Model Loss Isolation *VSWR (Reflective/ Pos. Supply Neg. Supply Ordering Additional(GHz) Number (dB, Max.) (dB, Min.) (Max.) Absorptive) (mA, Max.) (mA, Min.) Outline Options Features0.2–20.5–22–84–122–181–18STANDARD, MULTIOCTAVE BAND MODELSS403A 1.4 50 1.7:1 Ref 110 110 SP4T 1-5 –S403B 1.7 60 1.7:1 Ref 110 110 SP4T 1-5 –N403A 1.8 55 1.7:1 Abs 110 110 SP4T 1-5 –N403B 2.1 65 1.7:1 Abs 110 110 SP4T 1-5 –S413A 1.3 55 1.7:1 Ref 110 110 SP4T 1-5 –S413B 1.6 65 1.7:1 Ref 110 110 SP4T 1-5 –N413A 1.7 55 1.7:1 Abs 110 110 SP4T 1-5 –N413B 2 65 1.7:1 Abs 110 110 SP4T 1-5 –S436A 1.8 55 1.8:1 Ref 110 110 SP4T 1-5 –S436B 2 65 1.8:1 Ref 110 110 SP4T 1-5 –N436A 2 55 1.8:1 Abs 110 110 SP4T 1-5 –N436B 2.3 65 1.8:1 Abs 110 110 SP4T 1-5 –S447A 2.4 55 1.8:1 Ref 110 110 SP4T 1-5 –S447B 2.6 65 1.8:1 Ref 110 110 SP4T 1-5 –N447A 2.4 50 1.8:1 Abs 110 110 SP4T 1-5 –N447B 2.7 65 1.8:1 Abs 110 110 SP4T 1-5 –S438A 2.8 50 2:1 Ref 110 110 SP4T 1-5 –S438B 3.1 60 2:1 Ref 110 110 SP4T 1-5 –N438A 3 45 2:1 Abs 110 110 SP4T 1-5 –N438B 3.4 60 2:1 Abs 110 110 SP4T 1-5 –S428A 3 50 2:1 Ref 110 110 SP4T 1-5 –S428B 3.3 60 2:1 Ref 110 110 SP4T 1-5 –N428A 3.2 45 2:1 Abs 110 110 SP4T 1-5 –N428B 3.6 60 2:1 Abs 110 110 SP4T 1-5 –Electrical performance of multioctave models can be optimized over narrower bandwidths, or for a particular parameter. Electrical options include: Lowerinsertion loss, lower VSWR, higher isolation, flat amplitude response, amplitude tracking. Mechanical/Control options include: Custom packaging, singlesupply operation, fast switching time, single TTL control line. Examples of custom models previously shipped are shown below. Consult factory for options.OPTIMIZED PERFORMANCE MODELS0.5–4 125482 1.6 65 2:1 Ref 110 110 SP4T 5V, -15V5–6 127935 2.2 60 1.7:1 Abs 35 – Contact factory Single 5V supply5–6 126940 1.4 55 1.5:1 Abs 110 110 SP4T 5V,-15V9–11 127087 2.6 70 1.5:1 Abs 35 – Contact factory Single 5V supply3.4–12.8 126142 3 60 1.5:1 Ref – – Contact factory Single 5V supply*For reflective models, VSWR is not specified in the “OFF” state.For absorptive models, VSWR in the “OFF” state is defined for port J2 only.6

FEATURES• Multioctave bands 0.2 to 18 GHz• Current and TTL control• Low loss• High isolation• Medium and high speed models• Drop-in models• Amplitude and phase tracking• Binary decoded logicSINGLE-POLE FIVE-THROW SWITCHESFrequency Insertion Type DC Power ConsumptionRange Model Loss Isolation *VSWR (Reflective/ Pos. Supply Neg. Supply Ordering Additional(GHz) Number (dB, Max.) (dB, Min.) (Max.) Absorptive) (mA, Max.) (mA, Min.) Outline Options FeaturesSTANDARD, MULTIOCTAVE BAND MODELSS503A 1.5 50 1.7:1 Ref 135 135 SP5T 1-5 –0.2–2S503B 1.8 60 1.7:1 Ref 135 135 SP5T 1-5 –N503A 1.9 55 1.7:1 Abs 135 135 SP5T 1-5 –N503B 2.2 65 1.7:1 Abs 135 135 SP5T 1-5 –S513A 1.4 55 1.7:1 Ref 135 135 SP5T 1-5 –0.5–2S513B 1.7 65 1.7:1 Ref 135 135 SP5T 1-5 –N513A 1.8 55 1.7:1 Abs 135 135 SP5T 1-5 –N513B 2.1 65 1.7:1 Abs 135 135 SP5T 1-5 –S536A 1.9 55 1.8:1 Ref 135 135 SP5T 1-5 –2–8 S536B 2.1 65 1.8:1 Ref 135 135 SP5T 1-5 –N536A 2.1 55 1.8:1 Abs 135 135 SP5T 1-5 –N536B 2.4 65 1.8:1 Abs 135 135 SP5T 1-5 –S547A 2.6 55 1.8:1 Ref 135 135 SP5T 1-5 –4–12S547B 2.8 65 1.8:1 Ref 135 135 SP5T 1-5 –N547A 2.6 50 1.8:1 Abs 135 135 SP5T 1-5 –N547B 2.9 65 1.8:1 Abs 135 135 SP5T 1-5 –S538A 3 50 2:1 Ref 135 135 SP5T 1-5 –2–18S538B 3.3 60 2:1 Ref 135 135 SP5T 1-5 –N538A 3.2 45 2:1 Abs 135 135 SP5T 1-5 –N538B 3.6 60 2:1 Abs 135 135 SP5T 1-5 –S528A 3.2 50 2:1 Ref 135 135 SP5T 1-5 –1–18S528B 3.5 60 2:1 Ref 135 135 SP5T 1-5 –N528A 3.4 45 2:1 Abs 135 135 SP5T 1-5 –N528B 3.8 60 2:1 Abs 135 135 SP5T 1-5 –Electrical performance of multioctave models can be optimized over narrower bandwidths, or for a particular parameter. Electrical options include: Lowerinsertion loss, lower VSWR, higher isolation, flat amplitude response, amplitude tracking. Mechanical/Control options include: Custom packaging, singlesupply operation, fast switching time, single TTL control line. Consult factory for options.*For reflective models, VSWR is not specified in the “OFF” state.For absorptive models, VSWR in the “OFF” state is defined for port J2 only.7

FEATURES• Multioctave bands 0.2 to 18 GHz• Current and TTL control• Low loss• High isolation• Medium and high speed models• Drop-in models• Amplitude and phase tracking• Binary decoded logicSINGLE-POLE SIX-THROW SWITCHESFrequency Insertion Type DC Power ConsumptionRange Model Loss Isolation *VSWR (Reflective/ Pos. Supply Neg. Supply Ordering Additional(GHz) Number (dB, Max.) (dB, Min.) (Max.) Absorptive) (mA, Max.) (mA, Min.) Outline Options FeaturesSTANDARD, MULTIOCTAVE BAND MODELSS603A 1.6 50 1.7:1 Ref 160 160 SP6T 1-5 –0.2–2S603B 1.9 60 1.7:1 Ref 160 160 SP6T 1-5 –N603A 2 55 1.7:1 Abs 160 160 SP6T 1-5 –N603B 2.3 65 1.7:1 Abs 160 160 SP6T 1-5 –S613A 1.5 55 1.7:1 Ref 160 160 SP6T 1-5 –0.5–2S613B 1.8 65 1.7:1 Ref 160 160 SP6T 1-5 –N613A 1.9 55 1.7:1 Abs 160 160 SP6T 1-5 –N613B 2.2 65 1.7:1 Abs 160 160 SP6T 1-5 –S636A 2 55 1.8:1 Ref 160 160 SP6T 1-5 –2–8 S636B 2.2 65 1.8:1 Ref 160 160 SP6T 1-5 –N636A 2.2 55 1.8:1 Abs 160 160 SP6T 1-5 –N636B 2.5 65 1.8:1 Abs 160 160 SP6T 1-5 –S647A 2.7 55 1.8:1 Ref 160 160 SP6T 1-5 –4–12S647B 2.9 65 1.8:1 Ref 160 160 SP6T 1-5 –N647A 2.8 50 1.8:1 Abs 160 160 SP6T 1-5 –N647B 3.1 65 1.8:1 Abs 160 160 SP6T 1-5 –S638A 3.2 50 2:1 Ref 160 160 SP6T 1-5 –2–18S638B 3.5 60 2:1 Ref 160 160 SP6T 1-5 –N638A 3.4 45 2:1 Abs 160 160 SP6T 1-5 –N638B 3.8 60 2:1 Abs 160 160 SP6T 1-5 –S628A 3.4 50 2:1 Ref 160 160 SP6T 1-5 –1–18S628B 3.7 60 2:1 Ref 160 160 SP6T 1-5 –N628A 3.6 45 2:1 Abs 160 160 SP6T 1-5 –N628B 4 60 2:1 Abs 160 160 SP6T 1-5 –Electrical performance of multioctave models can be optimized over narrower bandwidths, or for a particular parameter. Electrical options include: Lowerinsertion loss, lower VSWR, higher isolation, flat amplitude response, amplitude tracking. Mechanical/Control options include: Custom packaging, singlesupply operation, fast switching time, single TTL control line. Examples of custom models previously shipped are shown below. Consult factory for options.OPTIMIZED PERFORMANCE MODELS0.6–2.5 122516 2.5 65 1.7:1 Abs 160 160 SP6T 5V,-5V9–11 126153 2.5 40 1.5:1 Ref 25 – Contact factory Single 5V supply*For reflective models, VSWR is not specified in the “OFF” state.For absorptive models, VSWR in the “OFF” state is defined for port J2 only.8

FEATURES• Multioctave bands 0.2 to 18 GHz• Current and TTL control• Low loss• High isolation• Medium and high speed models• Drop-in models• Amplitude and phase tracking• Binary decoded logicSINGLE-POLE SEVEN-THROW SWITCHESFrequency Insertion Type DC Power ConsumptionRange Model Loss Isolation *VSWR (Reflective/ Pos. Supply Neg. Supply Ordering Additional(GHz) Number (dB, Max.) (dB, Min.) (Max.) Absorptive) (mA, Max.) (mA, Min.) Outline Options FeaturesSTANDARD, MULTIOCTAVE BAND MODELSS703A 1.7 50 1.7:1 Ref 185 185 SP7T 1-5 –0.2–2S703B 2 60 1.7:1 Ref 185 185 SP7T 1-5 –N703A 2.1 55 1.7:1 Abs 185 185 SP7T 1-5 –N703B 2.4 65 1.7:1 Abs 185 185 SP7T 1-5 –S713A 1.6 55 1.7:1 Ref 185 185 SP7T 1-5 –0.5–2S713B 1.9 65 1.7:1 Ref 185 185 SP7T 1-5 –N713A 2 55 1.7:1 Abs 185 185 SP7T 1-5 –N713B 2.3 65 1.7:1 Abs 185 185 SP7T 1-5 –S736A 2.1 55 1.8:1 Ref 185 185 SP7T 1-5 –2–8 S736B 2.3 65 1.8:1 Ref 185 185 SP7T 1-5 –N736A 2.3 55 1.8:1 Abs 185 185 SP7T 1-5 –N736B 2.6 65 1.8:1 Abs 185 185 SP7T 1-5 –S747A 2.9 55 1.8:1 Ref 185 185 SP7T 1-5 –4–12S747B 3.1 65 1.8:1 Ref 185 185 SP7T 1-5 –N747A 3 50 1.8:1 Abs 185 185 SP7T 1-5 –N747B 3.2 65 1.8:1 Abs 185 185 SP7T 1-5 –S738A 3.4 50 2:1 Ref 185 185 SP7T 1-5 –2–18S738B 3.7 60 2:1 Ref 185 185 SP7T 1-5 –N738A 3.6 45 2:1 Abs 185 185 SP7T 1-5 –N738B 4 60 2:1 Abs 185 185 SP7T 1-5 –S728A 3.6 50 2:1 Ref 185 185 SP7T 1-5 –1–18S728B 3.9 60 2:1 Ref 185 185 SP7T 1-5 –N728A 3.8 45 2:1 Abs 185 185 SP7T 1-5 –N728B 4.2 60 2:1 Abs 185 185 SP7T 1-5 –Electrical performance of multioctave models can be optimized over narrower bandwidths, or for a particular parameter. Electrical options include: Lowerinsertion loss, lower VSWR, higher isolation, flat amplitude response, amplitude tracking. Mechanical/Control options include: Custom packaging, singlesupply operation, fast switching time, single TTL control line. Examples of custom models previously shipped are shown below. Consult factory for options.OPTIMIZED PERFORMANCE MODELS1–1.5 127069 1.5 60 1.6:1 Abs – – SP7T 2-3 15V, -15V 1nsswitch speed*For reflective models, VSWR is not specified in the “OFF” state.For absorptive models, VSWR in the “OFF” state is defined for port J2 only.9

SWITCH OUTLINE DRAWINGSSPSTSP2T0.18 [4.57]0.36 [9.14] MAX.0.80 [20.32]0.600 [15.25]0.10 [2.54] TYP.0.104 [2.64] DIA. THRU,4 HOLES TYP.0.11 [2.79]TYP.0.11 [2.79]TYP."SMA" FEMALECONNECTOR,TYP. (2) PLACESSP3TJ10.18 [4.57]+5 V-12 V0.800 [20.32]1.00 [25.40]J20.38[9.65]TYP.GND. PIN0.40 [10.16]0.40[10.16]0.18 [4.57] TYP. 0.80 [20.32]0.36 [9.14] MAX.0.10 [2.54] TYP.0.600 [15.24]0.104 [2.64] DIA. THRU,4 HOLES TYP.0.11 [2.79]TYP."SMA" FEMALECONNECTOR,TYP. (3) PLACESSP4TJ10.11 [2.79]TYP. 0.18 [4.57]E1J0E2J2+5V -12V0.800 [20.32]1.00 [25.40]GND. PIN0.18 [4.57]0.38 [9.65]TYP.0.40 [10.16]0.40 [10.16]GND. PIN0.270 [6.86]0.270 [6.86]0.310 [7.87]0.800 [20.32]0.10 [2.54] TYP.0.104 [2.64] DIA. THRU,4 HOLES TYP.0.11 [2.79]TYP."SMA" FEMALECONNECTOR,TYP. (4) PLACESJ1E1+5VJ0-12VE30.11 [2.79]TYP. 0.270 [6.86]TYP. (3) PLACESJ3E20.800 [20.32]1.00 [25.40]SQUAREJ20.38 [9.65]TYP.0.50 [12.70] TYP.0.18 [4.57]0.40 [10.16]GND. PIN0.550 [13.97] 0.35 [8.89]TYP.0.35 [8.89]TYP.0.10 [2.54]TYP."SMA" FEMALECONNECTOR,TYP. (5) PLACES1.300[33.02]0.104 [2.64] DIA. THRU,4 HOLES TYP.0.11 [2.79]TYP.0.11 [2.79]TYP.J1E1+12VJ0+5VE40.265 [6.73]TYP.J4J2E2E3J31.300 [33.02]1.50 [38.10]SQUARE0.38 [9.65]TYP.0.75 [19.05]TYP.0.18 [4.57]0.40 [10.16]0.265 [6.73]TYP.SP5TSP6TGND. PIN0.550 [13.97] 0.35 [8.89]TYP.0.35 [8.89]TYP.0.10 [2.54] TYP."SMA" FEMALECONNECTOR,TYP. (6) PLACES1.300[33.02]0.104 [2.64] DIA. THRU,4 HOLES TYP.0.11 [2.79]TYP.0.11 [2.79]TYP.J00.265 [6.73]TYP.J1E1-12V+5VE5J5J2E2E3J3E4J41.300 [33.02]1.50 [38.10]SQUARE0.265 [6.73]TYP.0.38 [9.65]TYP.0.18 [4.57]0.75 [19.05]TYP.0.40 [10.16]GND. PIN0.550 [13.97]0.35 [8.89]TYP.0.35 [8.89]TYP.0.10 [2.54] TYP."SMA" FEMALECONNECTOR,TYP. (8) PLACES1.300[33.02]0.104 [2.64] DIA. THRU,4 HOLES TYP.0.11 [2.79]TYP.0.11 [2.79]TYP.J00.265 [6.73]TYP.J1E1-12V+5VE6J61.300 [33.02]1.50 [38.10]SQUAREJ2E2 E3J3J4E4E5J50.265 [6.73]TYP.0.38 [9.65]TYP.0.18 [4.57]0.75 [19.05]TYP.0.40 [10.16]GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Unless specified, all connectors are type SMA femalefield replaceable. SMA male also available, seeordering options.3. Tolerance as follows:.xx = ±0.01 [.xx = ±0.25].xxx = ±0.005 [.xxx = ±0.13]10

SWITCH OUTLINE DRAWINGS (CONT.)SP7TGND. PIN"SMA" FEMALECONNECTOR,TYP. (8) PLACES1.300[33.02]J1E1+15 VJ0-15VJ7E7E6J6J2E2 E3J3J4E4E5J50.38 [9.65]TYP.0.75 [19.05]TYP.GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Unless specified, all connectors are type SMA femalefield replaceable. SMA male also available, seeordering options.3. Tolerance as follows:.xx = ±0.01 [.xx = ±0.25].xxx = ±0.005 [.xxx = ±0.13]0.10 [2.54] TYP.0.104 [2.64] DIA. THRU,4 HOLES TYP.0.11 [2.79]TYP.1.300 [33.02]1.50 [38.10]SQUARE0.18 [4.57]0.40 [10.16]0.11 [2.79]TYP.0.265 [6.73]TYP.0.265 [6.73]TYP.ORDERING INFORMATIONTo order a standard switch with specific parameters please include the following:Model NumberSpecify from tables on previous pages.Impedance Control OptionCurrent control, each throw:-2V @ 15 mA typ. (insertion loss)2V @ 20 mA typ. (isolation) . . . . . . . . . . . . . . . . . . . . . . . . . . BlankTTL driver, inverting logic“O” = Isolation, “I” = Insertion loss . . . . . . . . . . . . . . . . . . . . . . . DTTL driver, noninverting logic“I” = Isolation, “O” = Insertion loss . . . . . . . . . . . . . . . . . . . . . . . NRise/Fall Time, nsMedium: 300ns maximum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MFast: 20 ns, SP2T – SP7T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FUltrafast: 3 ns maximumAvailable in models S113, S136, S147 and S138 only . . . . . . . . UPower Supply5V, -12V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05V, -5V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V, -15V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2S236B D F OThe above illustrated switch Part Number S236B-D-F-O is based on the following parameters:2–8 GHz Single-Pole Double-Throw SwitchIsolation . . . . . . . . . . . . . . . . . 80 dB“OFF” state . . . . . . . . . . . . . . . ReflectiveImpedance control . . . . . . . . . TTL, inverting logicRise/fall time . . . . . . . . . . . . . . 20 ns maximumPower supply . . . . . . . . . . . . . 5V, -12VORDERING INFORMATION FOR RF CONNECTORSUnless otherwise specified on the purchase order, units will be shipped with field replaceable SMA female connectors on theinput and outputs. If male connectors are desired on any ports, specify on the purchase order.11

3 dB HYBRIDSFEATURES• 0°, 90° and 180° split• Up to 40 GHz• Compact package• Low loss• Tight amplitude and phase balanceMITEQ offers a variety of 3 dB hybrids including in-phase, quadrature, and 180 degree split types. Custom designscovering multioctave bands up to 40 GHz are also available. We offer MIL-STD-883 screening of our couplers andcan accommodate special connector requirements.Frequency Nominal Insertion Amplitude PhaseRange Model Split Loss Isolation Balance Balance RF(GHz) Number (dB) (dB, Max.) (dB, Min.) (±dB, Max.) (±Deg., Max.) VSWR Connectors Outline0° HYBRIDS35 – 40 D023540-0 3.01 1.5 18 0.5 5 1.7:1 K connectors, Seefield replaceable belowQUADRATURE 90° HYBRIDS35 – 40 D023540-90 3.01 1.5 18 0.5 5 1.7:1 K connectors, Seefield replaceable below180° HYBRIDS19 – 21 141295 3.01 1 20 0.25 5 1.5:1 K connectors, Seefield replaceable belowAdditional frequency ranges are available for all hybrids. Consult factory for options.ENVIRONMENTAL CONDITIONSOperating temperature . . . . . . . . . . . . . . . . 0 to 70°CStorage temperature . . . . . . . . . . . . . . . . . . -30 to +85°CFUNCTIONAL BLOCK DIAGRAMOUTLINE DRAWING.25 [6.35]1.00[25.4].82[20.83]0.104 [2.64]DIA.THRUTYP. (4) PLACES1.00[25.4].50 [12.7]INJ1.82[20.83]J20.125 [3.18]"K" CONNECTORTYP. (3) PLACES.50[12.7]GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]12

BROADBAND POWER DIVIDERSFEATURES• Multioctave bands• Microstrip construction• Low loss• High isolation• Small sizeMITEQ offers a broad range of Wilkinson-type power dividers covering multioctave bands from 2 to 18 GHz, andcustom power dividers up to 40 GHz are also available. Power dividers up to 16-way are available as standardproducts. These products feature excellent amplitude, phase balance and lowest possible loss. We can providethese components as drop-in functions for those applications that require higher levels of integration. We offer MIL-STD-883 screening and custom connector options.PhaseFrequency Insertion Amplitude Balance VSWR VSWRDivide Model Range Loss Isolation Balance (±Deg., In OutBy Number (GHz) (dB, Max.) (dB, Min.) (±dB, Max.) Max.) (Max.) (Max.) OutlineSTANDARD, MULTIOCTAVE BAND MODELSD0238 2–18 1.2 20 0.25 4 1.45:1 1.35:1 2D0239 2–26.5 2.5 20 0.5 5 1.6:1 1.5:1 22D0237 2–12.4 0.6 20 0.3 3 1.4:1 1.35:1 3D0236 2–8 0.4 20 0.2 2 1.4:1 1.3:1 3D0258 5–18 0.6 20 0.2 3 1.4:1 1.4:1 3D0249 4–26.5 1.2 18 0.4 4 1.6:1 1.6:1 3D0279 12–26.5 1 18 0.2 3 1.6:1 1.6:1 3D2089 18–40 1 17 0.5 5 1.8:1 1.7:1 3D0438 2–18 2.5 20 0.4 5 1.6:1 1.4:1 4D0437 2–12.4 1.7 20 0.35 4 1.5:1 1.4:1 44D0436 2–8 0.9 20 0.35 4 1.5:1 1.25:1 4D0458 5–18 1.5 20 0.35 5 1.6:1 1.4:1 5D0449 4–26.5 2.5 16 0.5 6 1.7:1 1.6:1 5D0479 12–26.5 1.8 16 0.5 6 1.75:1 1.6:1 5DO489 18–40 2.5 17 0.5 5 1.8:1 1.7:1 5D0837 2–12.4 2.8 20 0.4 5 1.6:1 1.4:1 6D0836 2–8 1.5 20 0.4 5 1.6:1 1.25:1 68 D0858 5–18 2 20 0.5 7 1.7:1 1.4:1 7D0849 4–26.5 3.7 16 0.6 7 1.8:1 1.6:1 7D0879 12–26.5 2.4 16 0.5 7 1.8:1 1.6:1 8DO889 18–40 3.5 17 0.5 5 1.8:1 1.7:1 816D1636 2–8 2.2 20 0.5 5 1.7:1 1.25:1 9D1658 5–18 3.5 20 0.5 7 1.8:1 1.5:1 10Electrical performance of multioctave models can be optimized over narrower bandwidths for a particular parameter. Electrical options include: Lower insertion loss,lower VSWR, higher isolation. Custom packaging also available. Examples of custom models previously shipped are shown below. Consult factory for options.OPTIMIZED PERFORMANCE MODELS119732 2.8–3.2 0.5 20 0.2 3 1.4:1 1.4:1 Contact factory2127071 15.7–16.2 0.5 20 0.2 10 1.5:1 1.5:1 Contact factory123287 8–14 1.2 20 0.25 3 1.4:1 1.4:1 Contact factory4125965 8–12.4 1.1 20 0.35 4 1.5:1 1.5:1 Contact factory8 126459 0.95–1.45 0.8 20 0.5 6 1.45:1 1.45:1 Contact factoryPower handling in a splitter application: 30 W CW @ load VSWR < 1.2:1, 10 W CW @ load VSWR < 2:1.ENVIRONMENTAL CONDITIONSOperating temperature . . . . . . . . . . . . . . . . 0 to 70°CStorage temperature . . . . . . . . . . . . . . . . . . -30 to +85°CPower handling . . . . . . . . . . . . . . . . . . . . . . P in maximum equals 20 W into 1.2:1 load, all ports.13

BROADBAND POWER DIVIDER OUTLINE DRAWINGS1, 2 and 3 4 and 50.104 [2.64] DIA. THRUTYP. (4) HOLES0.818[20.78]0.50[12.7]J0"SMA" FEMALECONNECTOR,TYP. (3) PLACESJ1J20.18 [4.57]TYP.0.25 [6.35]0.25 [6.35]1.00[25.4]"SMA" FEMALECONNECTORTYP. (5) PLACES0.31 [7.87]J4J30.50 [1.27]TYP.0.25[6.35]J2J10.25 [6.35]TYP. (5) PLACES0.09[2.29]0.31[7.87]OUTLINE DIM A1 3.5 [88.90]A0.31[7.87]0.25[6.35]TYP. (3) PLACES0.36[9.14]0.104 [2.64] DIA. THRUTYP. (4) HOLES0.31 [7.87]J0A0.104 [2.64] DIA. THRUTYP. (2) HOLES"SMA" FEMALECONNECTOR,TYP. (3) PLACES0.18 [4.57]TYP.1.84 [46.74]0.818[20.78]0.50[12.7]J0J1J20.25 [6.35]0.25 [6.35]1.00[25.4]0.18 [4.57] TYP.0.995 [25.27]0.075 [1.91]0.36[9.14]0.09[2.29]A/2OUTLINE DIM A2 1.5 [38.10]3 1.02 [25.91]A0.25[6.35]TYP. (3) PLACES0.36[9.14]OUTLINE DIM A4 2.5 [63.50]5 1.4 [35.56]1.99 [49.83]6, 7 and 8 9 and 100.36 [9.14]0.075 [1.91]1.995[50.67]3.99 [101.35]0.104 [2.64] DIA. THRUTYP. (4) HOLES3.84 [97.54]0.018 [0.46] TYP.0.36 [9.14]0.075[1.91]0.018 [0.46]TYP.3.995 [101.47]0.104 [2.64] DIA. THRUTYP. (4) HOLES7.99 [202.95]7.84 [199.14]JOJO0.31[7.87]0.31[7.87]A0.31[7.87]A0.31[7.87]J1J2 J3 J4 J5 J6 J7J8J1 J2 J3 J4 J5 J6 J7 J8 J9 J10 J11 J12 J13 J14 J15 J160.25[6.35] 0.50[12.70]0.25 [6.35]TYP. (9) PLACESTYP. "SMA" FEMALE CONNECTORTYP. (9) PLACES0.25 [6.35] TYP.(17) PLACES0.25 [6.35]TYP. "SMA" FEMALE CONNECTORTYP. (17) PLACES0.50 [12.7] TYP.OUTLINE DIM A6 3.5 [88.90]7 2.2 [55.88]8 1.75 [44.45]OUTLINE DIM A9 5.5 [139.70]10 2.9 [73.66]GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Unless specified, all connectors are type SMA female field replaceable.3. Tolerance as follows:.xx = ±0.01 [.xx = ±0.25].xxx = ±0.005 [.xxx = ±0.13]14

FEATURES• Attenuation range of up to 60 dB• Up to octave bandwidths• Analog control voltage• Lowest insertion lossANALOG PIN ATTENUATORSAnalog PIN attenuators optimized for the communication bands are available from MITEQ. Attenuation ranges upto 60 dB can be obtained with our standard products. We also offer as custom products 5-bit digital attenuators withan LSB of 1 dB and maximum attenuation of 30 dB. This design is ideal in IF applications up to 3 GHz. CustomPIN attenuators that cover octave bands are available. We also offer MESFET-based attenuators covering 0.2 to40 GHz in multioctave bands. These products offer very broad bandwidths and fast response time.Frequency Insertion *VSWR **Amplitude Atten. Range ***ControlRange Model Loss In/Out Response Options Options Additional(GHz) Number (dB, Max.) (Max.) (dB) (dB, Min.) (VDC) Outline FeaturesSTANDARD, MULTIOCTAVE BAND MODELS0.95–1.45 MPAT-095145- 1.1 1.5:1 See notes 10–60 0–20 1 –0.95–1.75 MPAT-095175- 1.1 1.5:1 See notes 10–60 0–20 1 –1.5–1.8 MPAT-150180- 1.1 1.5:1 See notes 10–60 0–20 2 –2.1–2.7 MPAT-210270- 1.5 1.5:1 See notes 10–60 0–20 2 –3.4–4.2 MPAT-340420- 2.2 1.5:1 See notes 10–60 0–20 2 –3.62–4.205 MPAT-362420- 2.2 1.5:1 See notes 10–60 0–20 2 –4.5–4.8 MPAT-450480- 2.2 1.5:1 See notes 10–60 0–20 2 –5.845–6.43 MPAT-584643- 2.2 1.5:1 See notes 10–60 0–20 2 –6.4–7.2 MPAT-640720- 2.2 1.5:1 See notes 10–60 0–20 2 –7.25–7.75 MPAT-725775- 2.2 1.5:1 See notes 10–60 0–20 2 –7.9–8.4 MPAT-790840- 2.2 1.5:1 See notes 10–60 0–20 2 –10.95–11.7 MPAT-109117- 2.2 1.5:1 See notes 10–60 0–20 4 –10.95–12.2 MPAT-109122- 2.2 1.5:1 See notes 10–60 0–20 4 –10.7–11.7 MPAT-107117- 2.2 1.5:1 See notes 10–60 0–20 4 –10.7–12.5 MPAT-107125- 2.2 1.5:1 See notes 10–60 0–20 4 –10.95–12.75 MPAT-109128- 2.2 1.5:1 See notes 10–60 0–20 4 –11.7–12.2 MPAT-117122- 2.2 1.5:1 See notes 10–60 0–20 4 –11.7–12.75 MPAT-117128- 2.2 1.5:1 See notes 10–60 0–20 4 –12.2–12.75 MPAT-122128- 2.2 1.5:1 See notes 10–60 0–20 4 –12.75–13.25 MPAT-128133- 2.5 1.5:1 See notes 10–60 0–20 4 –13.75–14.5 MPAT-138145- 2.5 1.5:1 See notes 10–60 0–20 4 –14–14.5 MPAT-140145- 2.5 1.5:1 See notes 10–60 0–20 4 –14–14.8 MPAT-140148- 2.7 1.5:1 See notes 10–60 0–20 4 –17.3–17.8 MPAT-173178- 2.7 1.5:1 See notes 10–60 0–20 5 –17.3–18.1 MPAT-173181- 3 1.5:1 See notes 10–60 0–20 5 –17.7–20.2 MPAT-177202- 3 1.5:1 See notes 10–60 0–20 5 –18.8–19.6 MPAT-188196- 3 1.5:1 See notes 10–60 0–20 5 –* VSWR is guaranteed over full attenuation range.** Amplitude response: ±0.2 dB p-p over any 40 MHz window, 1 dB p-p over full band from 0–30 dB attenuation.*** Insertion loss occurs at 0 V control.Custom models featuring broader bandwidths, and/or optimized specifications are also available. Consult factory for options.15

ANALOG PIN ATTENUATORS (CONT.)Frequency Insertion *VSWR **Amplitude Atten. Range ***ControlRange Model Loss In/Out Response Options Options Additional(GHz) Number (dB, Max.) (Max.) (dB) (dB, Min.) (VDC) Outline FeaturesVOLTAGE CONTROLLED1.275–1.48 MPAT-127148- 2.5 1.5:1 See notes 30 0–20 4 –1.654–1.746 MPAT-165175- 1.1 1.5:1 0.25 in band 20 0–20 2 –2–2.2 MPAT-124068- 1.7 1.5:1 0.3 in band 37 0–6 2 Input P1 dB = 20 dBmHigh power: 20 W peak,operating. 40 W peak,survival.3.1–3.5 124082 2.2 1.3:1 0.25 in band 15 0–5 –3.8–4.1 126149 1.3 1.5:1 1 max. at 20– 10–60 0–5 260 dB atten. –7.5–8.5 125964 1.8 1.5:1 0.25 in band 10 0–10 5 –8–12 124792 2.2 1.8:1 60 – 4 Attenuation flatness:±1.6 dB maximum150 ns switch speedmaximumCURRENT-CONTROLLED ANALOG PIN ATTENUATORS4–8 123293 2 1.7:1 0.3 at 10 dB 10–60 – 2 50 ns switch speed1.5 at 40 dB maximum1.6 at 60 dB8–12 124782 2.2 1.7:1 0.5 at 10 dB 10–60 – 4 –1.5 at 40 dB –1.6 at 60 dB –* VSWR is guaranteed over full attenuation range.** Amplitude response: ±0.2 dB p-p over any 40 MHz window, 1 dB p-p over full band from 0–30 dB attenuation.*** Insertion loss occurs at 0 V control.ENVIRONMENTAL CONDITIONSOperating temperature . . . . . . . . . . . . . . . . 0 to 70°CStorage temperature . . . . . . . . . . . . . . . . . . -30 to +85°CORDERING INFORMATIONMPAT- Model number - Desired attenuation (10–60 dB) - Desired control voltage (0–20 V)Example: To specify a 10.7–12.75 GHz, 40 dB attenuator with a control voltage of 15 volts, the following orderinginformation would be used: MPAT-107117-40-15.ORDERING INFORMATION FOR RF CONNECTORSUnless otherwise specified all units will be shipped with field replaceable SMA female connectors on the input andoutputs. If male connectors are desired on any ports, please specify on the purchase order.16

ANALOG PIN ATTENUATORS OUTLINE DRAWINGS1 20.10 [2.54]0.10 [2.54]0.10 [2.54]0.10 [2.54]0.18 [4.57]0.18 [4.57]GND PIN0.130 [3.30] DIA.THRU TYP.(2) HOLES0.45 [11.43]CONTROL SIGNAL0.03 [0.76] DIA. PIN TYP.0.38[9.65]TYP.0.36 [9.14]MAX.GND PIN0.104 [2.64] DIA.THRU TYP.(2) HOLES0.55[13.97]CONTROLSIGNAL0.38[9.65]TYP.0.36 [9.14]MAX.0.03 [0.76] DIA.PIN TYP.2.00[50.8]1.475[37.47]1.00[25.4]1.40[35.56]1.67[42.42]1.20[30.48]0.40[10.16]"SMA" FEMALECONNECTOR,TYP. (2) PLACES0.12[3.05]2.350 [59.69]2.60 [66.04]0.130.43 [3.30][10.92] TYP.0.50[12.7]1.10 [27.94]"SMA" FEMALECONNECTOR,TYP. (2) PLACES0.30[7.62]1.200 [30.48]1.80 [45.72]0.13[3.30]TYP.0.50[12.7]4 50.10[2.54]0.18 [4.57]"SMA" FEMALECONNECTOR,TYP. (2) PLACES0.38[9.65]TYP.GND PIN0.104 [2.64] DIA.THRU TYP.(2) HOLES0.08[2.03]0.42[10.67]CONTROLSIGNAL0.03 [0.76] DIA.PIN TYP.0.38[9.65]TYP. 0.36 [9.14]MAX.0.36 [9.14] MAX.0.80 [20.32]0.600 [15.25]0.10 [2.54] TYP.J1EJ20.40 [10.16]0.6501.25 [16.51][31.75]0.30 [7.62]"SMA" FEMALECONNECTOR,TYP. (2) PLACES0.10[2.54]1.050 [26.67]1.25 [31.75]0.750.50 [19.05][12.7]0.13[3.30]TYP.0.50[12.7]0.104 [2.64] DIA. THRU,4 HOLES TYP.0.11 [2.79]TYP.0.11 [2.79]TYP.0.18 [4.57]0.800 [20.32]1.00 [25.40]GND. PIN0.40[10.16]GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Unless specified, all connectors are type SMA female field replaceable.3. Tolerance as follows:.xx = ±0.01 [.xx = ±0.25].xxx = ±0.005 [.xxx = ±0.13]17

3 BIT, 9–10 GHzDIGITAL PHASE SHIFTERSPECIFICATIONS - MODEL 126138Phase states 0° (Ref.), 90°, 180°, 270°Frequency range9–10 GHzInsertion loss7 dB maximumVSWR1.7:1 maximumSwitching speed20 ns maximumPhase accuracy±5° maximumAmplitude balance±0.5 dB maximumControlTTL, 2 linesLogic truth table E1 E2 Phase0 0 0°0 1 90°1 0 180°1 1 270°DC power±5 V @ 50 mA maximumOutline drawing 14 BIT, 2.9–3.1 GHzDIGITAL PHASE SHIFTERSPECIFICATIONS - MODEL 124787Phase states 40° (Ref.), 22.5°, 45°, 90°, 180°Frequency range2.9–3.1 GHzInsertion loss3 dB maximumVSWR1.5:1 maximumSwitching speed25 ns maximumPhase accuracy1° maximumAmplitude accuracy0.25 dB maximumControlTTL, “0” = Path onOutline drawing 1PHASE SHIFTERSMITEQ offers a 6-BIT to 18 GHz digital phase shifter operating as high as 18 GHz for EW applications. This productoffers exceptional power handling capability in excess of 25 dBm and switching speed of 20 ns maximum. Thisdevice is ideally suited for phased array applications and interferometric receivers. We also offer a number ofnarrowband analog phase shifters that utilize switched line and reflection phase shifter topologies.6 BIT, 6–18 GHzDIGITAL PHASE SHIFTERSPECIFICATIONS - MODEL PS-0618-360-5-5.6RF frequency range6–18 GHzInsertion loss9 dB typical,12 dB maximumInput/output VSWR1.6:1 maximumMaximum phase shift 360°Phase shift step size5.6° minimumPhase error3° typical,6° maximum over RF bandInput third order intercept40 dBm typical,35 dBm minimumSwitching speed20 ns maximumDC control voltages0 V and -5.5 VNumber of control lines 9DC control connectorITT cannon MDM 9 pinRF connectorsSMA femaleOutline drawing 2ENVIRONMENTAL CONDITIONSOperating temperature . . . . . . . . . . . . . . . . 0 to 70°CStorage temperature . . . . . . . . . . . . . . . . . . -30 to +85°COUTLINE 1 OUTLINE 20.44 [11.18]0.11 [2.79] TYP.1.56 [39.62]0.34 [8.64]TYP.0.38[9.65]TYP.1.00 [25.4]0.10 [2.54]0.19 [4.83]TYP.0.57 [14.48]1.50[38.10]0.75[19.05]1.34[34.04]J1INE5E4E3E2GNDE1+5V-5VJ2OUT0.90[22.86]0.70[17.78]J1J20.13[3.30]TYP."SMA" FEMALECONNECTOR,TYP. (2) PLACES0.104 [2.642] THRUTYP. (4) HOLES0.03 [0.76] DIA. PINTYP. (8) PLACES0.10 [2.54]0.104 [2.64] DIA. THRUTYP. (4) HOLES0.380[9.65]"SMA" FEMALECONNECTORTYP. (4) HOLES0.86 [21.84]1.72 [43.69]MDM-9S9 8 7 65 4 3 2 1GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]18

MODULATORSMITEQ supports the wireless markets with BPSK and QPSK modulators that can handle data rates as high as 200Mb/s. We can offer spectral shaping filters to control spectral content and thereby achieve optimal spectrum utilization.RRC and Butterworth baseband shaping filters can be provided. Our modulators feature very good linearity to minimizespectral regrowth after shaping is performed. BIT error rates within 1 dB of theoretical can be achieved.Modulators supporting carrier frequencies up to 18 GHz and data rates as high as 200 Mb/s are available. Ourcommunications expertise is available to support you in achieving the optimum solution to your system problem.FEATURES• Voltage controlledSPECIFICATIONS - MODEL 124785RF frequency rangeInsertion lossInput/output VSWROn/off ratioSwitching speedDC control voltages13.5–14.5 GHz3 dB maximum1.7:1 maximum60 dB minimum150 ns maximum0 V = Off5 V = OnOUTLINE DRAWING0.10 [2.54]0.45[11.43]0.18 [4.57] TYP.0.10 [2.54]GND PIN0.104 [2.64] DIA. THRUTYP (2) HOLESCONTROL SIGNAL0.38[9.65]TYP.0.03 [0.76] DIA.PIN TYP.0.36 MAX.[9.14]GENERAL NOTES:1. Dimensions shown inbrackets [ ] are in millimeters.2. Tolerance as follows:.xx = ±0.01 [.xx = ±0.25].xxx = ±0.005 [.xxx = ±0.13]1.40[35.56]"SMA" FEMALECONNECTORTYP. (2) PLACES0.800[20.32]0.30[7.62]0.08[2.03]J41.140 [28.96]1.30 [33.02]J20.950.50[24.13][12.7]0.13 [3.30]0.50 [12.7]BPSK MODULATORSPECIFICATIONS - MODEL 1921649RF frequency rangeInsertion lossInput/output VSWRAmplitude balancePhase balanceSwitching speedDriver delayPower handlingControlModulation rateCarrier suppressionDC power10–10.3 GHz3 dB maximum1.8:1 maximum0.5 dB maximum10° maximum15 ns maximum40 ns maximum15 dBm CW maximumTTLDC–25 MHz15 dB minimum15 V @ 200 mA maximum-15 V @ 100 mA maximumENVIRONMENTAL CONDITIONSOperating temperature . . . . . . . . . . . . . . . . 0 to 70°CStorage temperature . . . . . . . . . . . . . . . . . . -30 to +85°C0.900[22.86]0.110 [2.79]0.375 [9.52]0.220 [5.59]0.104 [2.64] DIA.THRU, (4) HOLES0.720[18.29]0.090 [2.29]0.090 [2.29]J1"SMA" FEMALECONNECTORTYP. (2) PLACESJ2-15V E +15V0.720 [18.29]0.900 [22.86]GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]19

FEATURES• Less than 1.4 cubic inches• Biphase modulation to 50 MHz• Ruggedized for military applications• Integral dielectric resonator oscillator• Other frequencies availableBPSK MODULATORSSPECIFICATIONSPARAMETERS Model 121733 Model 124083RF carrier frequency (fixed) 3.8–4.5 GHz 7.6–9 GHzFrequency stability ±2.5 MHz ±2.5 MHzPhase noise < -95 dBc @ 10 kHz < -75 dBc @ 10 kHzTransmit power > 150 mW > 120 mWCarrier harmonics -20 dBc maximum -20 dBc maximumPushing 500 kHz maximum, over supply voltage 500 kHz maximum, over supply voltagePulling 500 kHz maximum, over specified load mismatch 500 kHz maximum, over specified load mismatchLoad mismatch No degradation for load of 3:1 maximum at any phase No degradation for load of 3:1 maximum at any phaseSettling time after power up 10 ms maximum 10 ms maximumOutput power (into 50 Ω) 22 dBm minimum 21 dBm minimumSupply voltage 6.5–9.5 V 6.5–9.5 VDC current 500 mA maximum 500 mA maximumModulation type BPSK BPSKAmplitude imbalance ±0.5 dB maximum ±0.5 dB maximumPhase imbalance ±5° maximum ±5° maximumCarrier suppression 20 dB minimum 25 dB minimumModulation signal current ±8–±20 mA ±8–±20 mAModulation signal (1 dB bandwidth) DC–50 MHz DC–50 MHzModulation input impedance 50 Ω in series with diodes, 20 pF maximum to ground 50 Ω in series with diodes, 20 pF maximum to groundContinuous operation At 25°C, without heatsink At 25°C, without heatsinkConnector J4 SMA removableConnectors J2, J3 and GND0.015 dia. pin, 50 ΩSolder pinsENVIRONMENTAL CONDITIONS Operating temperature . . . . . . . . . . . . . . . . 0 to 70°CStorage temperature . . . . . . . . . . . . . . . . . . -30 to +85°CFUNCTIONAL BLOCK DIAGRAMOUTLINE DRAWINGJ2DROJ31.030 [26.16]2.464 [62.60]0.116 [2.94]0.515 [13.08]MODULATION 0.030 [0.77] DIA. PIN0.030 [0.77] DIA. GND. PINDC SUPPLY 0.030 [0.77] DIA. PINVREG LPF LPFJ4TYPE "SMA" FEMALECONNECTOR (RF OUTPUT)0.600 [15.24]0.080 [2.03]0.080 [2.03]1.341 [34.06]0.325 [8.26] TYP. APPROX.0.846 [21.49]0.418 [10.62]0.375 [9.52]0.249 [6.31]0.147 [3.73]0.080 [2.03]0.080 [2.03]0.202 [5.13]GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]0.870 [22.09]#2–56 UNC-2B X 0.18 [4.57] DP. MIN.TYP. (4) HOLES, BOTH SIDES (TOTAL 8 HOLES)±0.005-0.0000.0630 [1.60]X 0.200 [5.08] DP.(2) HOLES0.499[12.67]0.342 [8.69]±0.0020.626 [15.89]20

FEATURESQPSK MODULATORS• Switching speed ..................... 150 ns maximum• Phase accuracy ...................... ±5° maximum• Amplitude balance ................. ±0.75 dB maximumSPECIFICATIONSPARAMETERS Model 127072 Model 131008Function Phase shifter, 2-BIT (QPSK) Phase shifter, (QPSK)Frequency range 2.2–2.3 GHz 13.3–14.1 GHzPhase states 0°, 90°, 180°, 270° 0°, 90°, 180°, 270°Insertion loss 8 dB maximum 8 dB maximumVSWRJ1, RF input 2:1 maximum 2:1 maximumJ2, RF output 3:1 maximum 3:1 maximumControl TTL, 2 lines (E1, E2) TTL, 2 lines (E1, E2)Switching speed 150 ns maximum 150 ns maximumPhase accuracy ±5° maximum ±5° maximumAmplitude balance ±0.75 dB maximum ±0.75 dB maximumDC power ±5 V @ 75 mA maximum each ±5 V @ 75 mA maximum eachControl logic E1 E2 State0 0 0°0 1 90°1 0 -90°1 1 180°ENVIRONMENTAL CONDITIONSOperating temperature . . . . . . . . . . . . . . . . 0 to 70°CStorage temperature . . . . . . . . . . . . . . . . . . -30 to +85°COUTLINE DRAWING0.225 [5.71]0.10 [2.54]1.75 [44.45]2.38 [60.45]0.38 [9.65]TYP. (4) PLACESSMA FEMALE CONNECTORTYP. (4) PLACES1.56 [39.62]1.30 [33.02]1.09 [27.69]1.31 [33.27]0.78 [19.81]0.26 [6.60]0.45 [11.43]0.125 [3.18]0.120 [3.048] DIA. THRUTYP. (3) PLACESGENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]21

COUPLERSFEATURES• High directivity through phasevelocity compensation• Stripline and microstripcouplers available• Lowest insertion lossINCOUTMITEQ offers a variety of single and multisection microstrip and stripline couplers featuring a wide range of couplingvalues and bandwidths. MITEQ can offer microstrip couplers that incorporate compensation to enhance directivityby as much as 15 dB.Frequency Insertion VSWR VSWR VSWRModel Range Coupling Loss In Out CoupledNumber (GHz) (dB) (dB, Max.) (Max.) (Max.) (Max.) OutlineNARROWBAND COUPLERS125471 6.3–6.9 20 1.3 1.6:1 1.6:1 1.8:1 See below131009-70058 15.4–19.8 Out 1 = 20 3 1.6:1 1.6:1 2:1 Contact factoryOut 2 = 6124788-19.328 19.3–19.5 20 1.3 1.8:1 1.8:1 1.9:1 See below124788-29.1 29–29.2 20 1.3 1.8:1 1.8:1 1.9:1 See below125955 30 20 1.5 1.8:1 1.8:1 2:1 See belowAdditional frequency ranges and coupling values are available. Consult factory for options.ENVIRONMENTAL CONDITIONSOperating temperature . . . . . . . . . . . . . . . . 0 to 70°CStorage temperature . . . . . . . . . . . . . . . . . . -30 to +85°CPower handling . . . . . . . . . . . . . . . . . . . . . . P in maximum equals 20 W into 1.2:1 load, all ports.OUTLINE DRAWINGTYPE "SMA" FEMALECONNECTOR TYP. (3) PLACES0.25[6.35]0.104 [2.64] DIA. THRUTYP. (2) PLACESC0.50 [12.7]0.23 [5.84] TYP.INOUT0.370[9.40]TYP.0.41[10.41]0.344[8.74]1.16 [29.46]0.09 [2.29]0.37[9.40]0.185 [4.70]TYP. (3) HOLESGENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]22

LIMITERSFEATURES• Optimized for lowestspike and flat leakage• Designs suitable for sensitivePHEMT front ends• Lowest insertion loss• Power handling up to 60 dBmMITEQ has extensive experience in the design and development of limiters for receiver protection. We specializein developing limiters for critical radar receiver applications and EW applications. Designs based on PIN diodes,Schottky diodes, and combinations of the two semiconductor technologies are also available. In applications thatrequire extremely fast response time MITEQ can offer a customized solution that meets your needs. We can providelimiters that safely handle pulsed power levels up to 60 dBm. These designs feature PIN diodes with plated heatsinkthat are eutecticly-attached to a carrier for best possible thermal transfer. We offer limiters that feature Schottkydiode arrays for the ultimate in insertion loss, flat output leakage and minimal spike leakage.Frequency Insertion VSWR RF Flat Spike IP 3 RecoveryModel Range Loss In/Out Power Leakage Leakage (dBm, TimeNumber (GHz) (dB, Max.) (Max.) (Max.) (dBm) (erg) Min.) Linearity (ns, Max.) Outline126159 0.5–1 0.7 1.3:1 1W CW. 400W peak, 20 0.2 25 -50–0 dBm, 500 A1µs 0.1% DC w/in 0.1 dB126160 1–2 0.7 1.3:1 1W CW, 20 0.2 25 -50–0 dBm, 500 A400W peak,w/in 0.1 dB1µs 0.1% DC126156 0.5–2 1.5 1.5:1 100W peak, 15 0.2 B10 µs pulse129186 2.7–2.9 0.8 1.5:1 1W CW, 52 dBm peak, 20 0.2 100 A80 µs pulse, rate: 1.4 msAdditional bandwidths from 2–18 GHz are available. Consult factory for options.ENVIRONMENTAL CONDITIONSOperating temperature . . . . . . . . . . . . . . . . 0 to 70°CStorage temperature . . . . . . . . . . . . . . . . . . -30 to +85°COUTLINE AOUTLINE B0.9 [22.86]0.45[11.43]0.51[12.95]REF.0.38[9.65]0.50[12.7] 0.32[8.13]0.25[6.35]0.44[11.18]0.32[8.13]OUT"SMA" FEMALECONNECTOR0.093 [2.36] DIA. THRUTYP. (2) PLACES"SMA" MALECONNECTOR0.25 [6.35]0.48[12.19]GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]IN0.80[20.32]0.10 [2.54] TYP.0.11 [2.79]TYP.0.600[15.25]0.104 [2.64] DIA. THRU,4 HOLES TYP.INOUT0.800 [20.32]1.00 [25.40]"SMA" MALE CONNECTOR0.40[10.16]"SMA" FEMALECONNECTOR0.40[10.16]23

CUSTOM INTEGRATEDASSEMBLIESCUSTOM INTEGRATED ASSEMBLIESMITEQ offers hundreds of man-years ofexperience in the design and developmentof the most demanding custom integratedassemblies. We can offer superior subsystemsolutions because we have completecapabilities in all of the components that gointo the most advanced systems. Thebreadth of experience includes low noisesignal sources, low- and medium-poweramplifiers, mixers, switches, highperformancefilters and filter banks, mixers,etc. All of this capability under one roofensures the highest standard in systemperformance because we understand ourcomponents.We can offer highly integrated solutions toyour system problems and routinely offerdensely packed slices containing as manyas 50 microwave functions in a smallvolume.We have extensive experience in developingcustom assemblies for space and wecurrently support JPL on their EOS-MLS andMIRO programs, and we support a numberof classified space programs.The following pages provide a limitedsampling of our capabilities. We welcomeyour inquiries.24

THREE-CHANNEL RECEIVER ASSEMBLYMITEQ’s low-noise monopulse receiver developmenthas drawn on the entire company’s capabilitiesto provide a very small, lightweight assemblyfor missile applications that has passedstringent electrical andenvironmental tests.The video output of the IRM is passed to anextremely compact video processor. Control of all ofthe receiver functions, such as gain control, BIT,calibration, LO selection, etc., is implemented viaserial link.The entire three-channel receiver assembly ispackaged in a machined aluminum housingand divided into three levels: microwavecavity, first IF cavity, and videoprocessor assembly.All front end circuitry isassembled in microwavecavities. Outputs of the firstdown conversion stagesare routed via glass tometal feedthroughsto the first IF cavitylocated directlyunderneath.25Each channel of the receiver employs a dual downconversion scheme. The first LO is derived from twointegral selectable phase-locked oscillators. Thesecond down conversion uses image reject mixers(IRMs) with ultra wideband activequadrature combiners.DCNOISEBITSPECIFICATIONSOperating frequency10 GHzConversion gain70 dBNoise figure2.5 dBAmplitude tracking1.5 dBPhase tracking 20°Channel-to-channel isolation 40 dBX-BAND PORTIONSW1LIM/LNA1NOISEDIODEFO=10.5 GHzBW=1 GHzLO1 BITLO1 OUT50 MHzEFBPF1ISO1MXR1 AMP1ATN1 ATN1ISO2DC1DIV2 AMP LO1CRO MULT.X45 GHzL-BAND PORTIONAMP2QIFMBPFFO=9.0 GHzBW=500 MHzAMP1The video processor containsactive quadrature combiners,bandpass filters, SP2T switches, seriallink, and power management circuitry.At each level, the assembly is channelized to meetthe required channel-to-channel isolation andprevent crosstalk of the LO, IF, andswitch transients.LO2CH.2ACTIVEQUADDIVLO2AMP LO2LO2CH3AMP3COMBINERAMP QVIDEO PORTIONAMP4 BPF2 EQUALIZERSBPF3SW2 SW3AMP5 EQUALIZERSLO2BITLO2 INPHASE GAINDC POWERFILTERINGSATEDAMP 6 COMPEN-VACTIVECLAMPERDC (+5,+15ATN. CONTROLSW1 CONTROL CONTRO&NOISE DIODE PLDSTATUCONROLFROM BITDETECTORS

CONVERTER ASSEMBLIESS-BAND TO X-, Ku-BAND UPCONVERTER MODULESPECIFICATIONSIF input frequency2–4 GHzLO input frequency10, 12 and 14 GHzRF output frequencyX-band, Ku-bandConversion loss15 dBBand selection switching speed15 nsBand selection isolation60 dBLO-to-IF leakage30 dBVSWR (all ports) 2.5:1S-band IF inputpower dividerMicrowave IF mixerSP3T absorptiveswitch X-bandLO selectorGPO blind mateRF connectorsX-, Ku-bandoutput bandpassfilterMultipin DC andlogic connectorX-, Ku-BAND TO S-BAND DOWNCONVERTER MODULESPECIFICATIONSRF input frequencyX-band, Ku-bandLO input frequency10, 12 and 14 GHzIF output frequency2–4 GHzConversion loss20 dBLO-to-RF isolation25 dBLO-to-IF isolation45 dBRF-to-IF isolation25 dBVSWR (all ports) 2.5:1QUADRATURE IF MIXERS-band outputlowpass filterGPO blind mateRF connectorsMicrowave IFmixersS-band IF5-way powercombiner andlowpass filtersAGC MODULESPECIFICATIONSRF, LO frequency range1.25–1.55 GHzIF frequency rangeDC–100 MHzConversion loss10 dB maximumLO-to-RF isolation22 dB minimumLO-to-IF isolation25 dB minimumAmplitude unbalance±0.5 dB maximumPhase deviation from 90°±3° maximumVSWR RF3:1 maximumVSWR LO2:1 maximumLO drive level7–10 dBmAmplitude tracking, set of 3±1.0 dB maximumPhase tracking, set of 3±5° maximumSPECIFICATIONSFunctionCoarse AGC, 4 bitFrequency range1.25–1.55 GHzGain32 dB nominalNoise figure9 dB maximumOutput power (1 dB comp.)8 dBm minimumAttenuation range32 dB nominalNumber of bits 4Bit sizes4, 8, 16, and 8 dBAttenuation accuracy±1 dB maximumPhase change vs. attenuation±10° maximumAttenuation control15 mA = ref.,-15 mA= attenuationDC power supply5 V @ 65 mA typicalAmplitude tracking, set of 3±0.5 dB maximumPhase tracking, set of 3±5° maximumMiniature modular subassemblies operating in the 1.25 to1.55 GHz frequency range were developed for airborneradar applications. Each of the specified units, theQuadrature IF Mixer and the AGC Module, measure only1.0 x 1.0 x 0.22 inches. These modules were produced insets of three amplitude and phase matched units andoperate over the temperature range of -35 to +85°C.26

FEATURES3–21 GHz THREE-CHANNEL DOWNCONVERTERMODEL: 136460• High reliability, spaceborne application• Broadband RF/LO coverage..... 3–21 GHz• Broadband IF operation............ 250–1550 MHz• LO power range......................... 10–16 dBm• Conversion gain ........................ 25 dB nominal• LO/RF isolation.......................... 30 dB typ., 20 dB minimum• LO/IF isolation ........................... 40 dB typ., 30 dB minimum• Digital gain control.................... 0–31.5 dB, 0.5 dB steps• Low power ................................. 165 mA (5 V),2 mA (-5 V) typ. per channel• Lightweight ................................ 400 grams typicalMITEQ’s model 136460 broadband three-channel downconverter functions as the second IF down conversion stageof a low earth orbit-based millimeter-wave radiometer. Coupled with one of five MITEQ frequency multiplexers asan input stage, the system provides maximally flat frequency response over the bands of interest, high linearity ofoutput power to input power, and high isolation between the frequency bands of interest as well as from otherundesirable signals. In addition, this high reliability, spaceborne integrated assembly is optimized for small size, lowpower consumption, lightweight, and excellent thermal stability of operation.ELECTRICAL SPECIFICATIONSRF INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.Frequency range GHz 3.2 21.2IF/RF VSWR Ratio 1.5:1LO frequency range GHz 4.8 19.5LO power dBm 10 16LO VSWR Ratio 2.5:1IF OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.Number of IF outputs Per channel 2Operating range MHz 250 1550RF-to-IF gain At maximum gain dB 25Digital attenuator control step size 6-BIT control dB 0.5Digital attenuator dB 0 31.5Output power (1 dB compression) dBm -1 0Calibration port coupling value dB 16Coupling flatness 250–1550 MHz dB ±1VSWR 250–1550 MHz Ratio 1.5:1OTHER PARAMETERS CONDITION UNITS MIN. TYP. MAX.LO-to-RF isolation dB 20 30LO-to-IF isolation dB 30 40Connectors, RF, IF, LOSMAConnectors, DC, control 1 per channel 15-pin, micro DSupply voltage Volts ±5DC power consumption for each At 5 V per channel mA 165downconverter At -5 V per channel mA 2Weight Grams 400ENVIRONMENTAL CONDITIONSOperating temperature . . . . . . . . . . 10 to 60°CStorage temperature . . . . . . . . . . . -25 to +60°CVibration . . . . . . . . . . . . . . . . . . . . 6.5 Gs RMS, 20–2000 HzRadiation . . . . . . . . . . . . . . . . . . . . 30 krads, total DOSP27

MODEL 136460 TYPICAL DATAGAIN VARIATION VS. TEMPERATURE (-10 TO +70°C). LO=10 GHz, USB32.52CHANGE IN GAIN FROM ROOMTEMP. (+25°C) (dB)1.51+70°C0.50-0.5-1-1.5-2-2.5-10°C-30.25 0.35 0.45 0.55 0.65 0.75 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55IF FREQUENCY (GHz)GAIN (dB)22212019181716IF RESPONSE, USB, ATTEN. SETTING = 7 dBLO = 5 GHzLO = 10 GHzLO = 19.5 GHz150 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8IF FREQUENCY (GHz)GAIN (dB)22212019181716150IF RESPONSE, LSB, ATTEN. SETTING = 7 dBLO = 5 GHzLO = 10 GHzLO = 18.5 GHz0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8IF FREQUENCY (GHz)FUNCTIONAL BLOCK DIAGRAMSGENERIC SYSTEM MODEL 136460ANTENNA100 -2500 GHz1ST LO5 RECEIVERSMITEQ MULTIPLEXER 1-53-21GHzAMP1MITEQ 136460 DOWNCONVERTERIF OUT250 -1550 MHzIF OUTCAL PORT2ND LO5-19.5 GHzCW3-21 GHz1300 MHz BWTO DOWNCONVERTER450 MHzVOLTAGE TOFREQ.CONVERTERV-FCHANNELCALSOURCELSB=0.5dBRF IN MXR LPF1 AMP1 EQL6 BITAMP2ATNLO INOUT1OUT2CAL INOUTLINE DRAWING0.410 [10.41]0.150[3. 81]0.250 [6.35] TYP.0.125[3.18]0.125[3.18]4.275 [108.59]2.675 [67.95]0.250[6.35]0.625 [15.88]0.410 [10.41]4.867[123.62]3.973[100.91]3.235[82.17]2.341[59.46]1.603[40.72]0.709[18.01]0.125 [3.18]DIA. THRU TYP. (6) PLACESGENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]J1J13J2J14J3J15J16J4J5J6J7J8J9J10J11J12J17 J180.989[25.12]1.945 [49.40]3.458 [87.83]5.575[141.61]1.700[43.18]1.1560.612 [29.36][15.54]0.225 [5.72]"SMA" FEMALE CONECTORSTYP. (15) PLACES4.420[112.27]3.876[98.45]3.332[84.63]2.788[70.82]2.244[57.00]4.964[126.09]28

MINIATURE DOWNCONVERTERFEATURES• Single and multi-channel radarreceiver front ends• Single and multi-channelfrequency converters• Switch filters• Switch amplifiers• Frequency multiplexers• Transmit/receive modulesMODEL: 127091+5 E1 E2 E3AZ1AZ1AZ2AZ2REF P/N 127091EL1EL1EL2EL2CAL LOSPECIFICATIONSPARAMETERS LIMITS CONDITIONSInput frequency range 6–18 GHz AZ1, AZ2, EL1, EL2, REF, CAL,Input signal power10 dBm maximumEMI input2 W CW maximumLO frequency range5.4–18.6 GHzLO power20 dBm, ±2 dBmLO leakage at the outputs -47 dBm MHz LO to AZ1 and 2 OutLO to EL1 and 2 OutOutput frequency rangeDC–600 MHzGain -15 dB typical, -16 dB maximum AZ to AZ Out, EL to EL Out-17 dB typical, -18 dB maximum REF to AZ Out and EL Out-21.5 dB typical, -23 dB maximum CAL to AZ Out and EL OutIsolation -50 dB AZ to EL-45 dB AZ1 to AZ2, EL1 to EL2Amplitude unbalance 1.4 dB maximum Note 1Phase unbalance ∆ + 8° maximum Note 1Phase unbalance 10° maximum REF to AZ1, AZ2 or EL1, EL2Switching speed 2 µs maximum All switchesDC power 5 V @ 175 mA maximum 5 V regulated supplyControl TTL E1 and E2Note 1:Amplitude and gain unbalance is defined as a change in the channel-to-channel output amplitude or phase with reference to therespective phase and amplitude outputs of the assembly. When the switch is in the CAL vs. the direct AZ and EL antenna positionsover the operating environment (i.e., residual amplitude and phase changes that cannot be calibrated out by reference to the CALsignal), phases may vary by a ∆ which corresponds to a fixed line length difference.ENVIRONMENTAL CONDITIONSWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 gramsOperating/storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -54 to +71°C29

MODEL 127091 TYPICAL DATAFUNCTIONAL BLOCK DIAGRAMAZ1LIM1SP2T_AZ2HPFRXLLPFAZ1OUTGND5 VE1AZ2LIM132 WAYDIV.HRBDQUAD.E22REF.LIM2 WAYDIV.SP3T_AZCALINSP3T_ELHPF2 WAYDIV.HPFRRLXXLLPFLPFAZ2OUTEL1OUT2 WAYDIV.LOIN2EL1LIM132 WAYDIV.HRBDQUAD.2EL2LIM1SP2T_ELHPFRLXLPFEL2OUTOUTLINE DRAWING0.12 [3.05]1.510 [38.35]SOLDER PINSTYPE "GPO" MALE CONNECTOR,FULL DETENT, TYP. (11) PLACES+5 E1 E2 E3AZ1AZ10.762 [19.35]AZ20.423 [10.75]AZ2REF0.762 [19.35]0.423 [10.75]EL1EL1EL2EL2CAL LO±0.0100.28 [17.14] 1.188 [30.18]0.104 [2.64] DIA. THRUTYP. (4) HOLES0.47[11.94]0.556[14.12]0.276 [7.01]0.663 [16.84]0.276 [7.01]0.663 [16.84]±0.0100.065 [0.25]1.870 [47.50]0.19 [4.83] X 0.19 [4.83] CHAMFERTYP. (4) CORNERS2.00 [50.8]0.40 [10.16]45° CHAMFER0.051 [1.30] X 0.015 [0.38]TYP. (2) PLACES1.75 [44.45]0.131 [3.33]GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]30

FEATURES• Three bands of operation coveringS-, C- and X-bands• Image rejection greater than 80 dB• 2 GHz IF frequency• LO leakage less than -80 dBmTRI-BAND DOWNCONVERTERMODEL: 131724SPECIFICATIONSPARAMETERS LIMITS CONDITIONSRF input frequency rangeBand 13.62–4.2 GHzBand 27.25–7.75 GHzBand 3a10.95–11.9 GHzBand 3b11.7–12.75 GHzRF input power-18 dBm nominalIF output frequency2 GHzLO powerLO = 5.62–6.2 GHz15 dBmLO = 9.25–12.75 GHz10–11 dBmConversion loss16 dB maximumGain flatness 0.2 dB for any 40 MHz segment, Over 0 to 50°C1 dB over any frequency bandGain variation between any 2 bands1 dB maximumGroup delay (any 40 MHz band) Over 0 to 50°CLinear.01 ns/MHz maximumParabolic.005 ns/MHz, 2 maximumRipple0.5 ns p-pInput/output VSWR1.5:1 maximumOutput power(1 dB compression)-8 dBm minimumSpurious Signal related -65 dBc maximum Signal level -18 dBmDC voltage supply5 VConnectors, RF, IF, LOSMA femaleConnector, DCMultipin MDM-9P (ITT)Frequency rejectionsBand 1: a) Image = 7.62–8.2 GHz> 80 dBcb) LO = 5.62–6.2 GHz < -80 dBm input, < -90 dBm outputBand 2: a) Image = 11.25–11.75 GHz> 80 dBcb) LO = 9.25–9.75 GHz < -80 dBm input, < -90 dBm outputBand 3: a) Image = 14.95–16.75 GHz> 80 dBcb) LO = 12.95–14.75 GHz < -80 dBm input, < -90 dBm outputControlOpen Ckt = OFF, GND = Band selectENVIRONMENTAL CONDITIONSWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 gramsOperating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 70°CStorage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30 to +85°C31

MODEL 131724 TYPICAL DATAOUTLINE DRAWING5.58 [141.73]0.67[17.02]0.106 [2.69]0.18 [4.57]5.368 [136.35]0.125 [3.175] DIA. THRU. C'BORE. 0.250 [6.35] DIA. X0.15 [3.81] DP. RUNOUT AS SHOWN, TYP. (4) PLACESLO12.638 [67.005]2.85[72.39]PIN 10.64[16.26]6 7 8 9MDM-9P1 2 3 4 51.35[34.29]RF INLO 3-4IF OUTLO 22.25[57.15]1.442[36.626]1.076[27.330]0.24 [6.10]0.106 [2.692]TYPE "SMA" FEMALECONNECTOR TYP. (5) PLACES0.471 [11.963]0.18 [4.57]TYPE "MDM-9P"CONNECTOR0.47[11.94]GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]32

TWO CHANNEL, SINGLE LO INPUT DOWNCONVERTER ASSEMBLYCUSTOM INTEGRATED ASSEMBLIESMODEL: 127089FEATURES• Single LO port, dual RF/IF ports• RF input frequency ............... 1.95–5.2 GHz• Conversion loss .................... 5 dB nominalLO +12 V GNDRF1 IF1 IF2 RF2SPECIFICATIONSPARAMETERSLIMITSRF input frequency range1.95–5.2 GHzRF input power-65 to -2 dBmLO input frequency2.7–4.45 GHzLO input power0 dBm ±2 dBmIF output frequency750 MHz ±50 MHzRF-to-IF gain-5 dB ±2 dBSSB Noise Figure 15 dB maximum @ 25°CIP 3 out 17.5 dBm minimum @ 25°CSingle-tone mixer products-25 dBc maximum, 0 to ±1 MHz from carrier, RF input -65 to -2 dBm-30 dBc maximum, ±1 MHz from carrier and above, RF input -20 to -2 dBm-45 dBc maximum, ±1 MHz from carrier and above, RF input -65 to -20 dBmIF output leakage-80 dBm maximum, 750 MHz ±50 MHz, RF - OffLO-to-RF leakage-10 dBm maximumLO-to-IF leakage-60 dBm maximumIsolation50 dB minimum, RF1 to IF2, RF2 to IF1VSWR RF1 and RF21.7:1 maximumVSWR LO2:1 maximumVSWR IF1 and IF21.8:1 maximumDC power12 V @ 375 mA maximumFUNCTIONAL BLOCK DIAGRAMOUTLINE DRAWINGRF12.65 [67.31]2.47 [62.74]0.40[10.16]0.11[2.79]IF1IF2RF2LO1.50[38.10]1.33[33.78]LO+12 V GNDRF1 IF1 IF2 RF2GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]0.55[13.97]0.69[17.53]0.55[13.97]0.12[3.05]33

FEATURES2.8–9.9 GHz FREQUENCY MULTIPLEXERMODEL: 136466• High reliability, spaceborne application• Broadband RF coverage.......... 2.8–9.9 GHz• RF gain...................................... 23 dB nominal• Channel-to-channel isolation.. 45 dB minimum• Input/output VSWR................... 1.5:1 typ., 1.8:1 maximum• Noise figure .............................. 3.5 dB typ., 4.5 dB maximum• Low power ................................ 325 mA (5 V) typical• Lightweight ............................... 520 grams typicalMITEQ’s model 136466 broadband-three output frequency multiplexer precedes the second IF down conversionstage in a low earth orbit-based millimeter-wave radiometer. In combination with the MITEQ second IFdownconverter, the system provides maximally flat frequency response over the bands of interest, high linearity ofoutput power to input power, and high isolation between the frequency bands of interest as well as from otherundesirable signals. In addition, this high reliability, spaceborne integrated assembly is optimized for small size, lowpower consumption, lightweight, and excellent thermal stability of operation.ELECTRICAL SPECIFICATIONSRF INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.Frequency range GHz 2.8 9.9VSWR Ratio 1.5:1 1.8:1RF OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.Number of RF output channels 3Channel 2 dB bandwidth MHz 1300Channel 20 dB rejection bandwidth MHz 2300Channel center frequencies GHz 3.9449, 5.7085, 9.1168Nominal gain dB 23Output power (1 dB compression) dBm -8 -5Noise figure dB 3.5 4.5Isolation between output channels dB 45VSWR Over 1300 MHz passband Ratio 1.5:1 1.8:1VOLTAGE TO FREQUENCYOUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.Number of output channels 4Channel 3 dB bandwidth MHz 450Channel 30 dB rejection bandwidth MHz 1000Channel center frequencies GHz 3.06, 4.76, 7.26, 7.86Output full scale frequency kHz 90OTHER PARAMETERS CONDITION UNITS MIN. TYP. MAX.Digital gain control 4 BIT Binary, TTL; BIT 5 = OFF state dB 0 7.5Gain control step size dB 0.5Connectors, RFSMAConnectors, DC control,21-pin, micro Dvoltage-frequency outputsSupply voltage Volts ±5DC power consumption for each At 5 V Supply mA 325downconverter At -5 V Supply mA 2.5Weight Grams 52034

2.8–9.9 GHz FREQUENCY MULTIPLEXER (CONT.)ENVIRONMENTAL CONDITIONSOperating temperature . . . . . . . . . . 10 to 60°CStorage temperature . . . . . . . . . . . -25 to +60°CVibration . . . . . . . . . . . . . . . . . . . . 6.5 Gs RMS, 20–2000 HzRadiation . . . . . . . . . . . . . . . . . . . . 30 krads, total DOSPFUNCTIONAL BLOCK DIAGRAMSGENERIC SYSTEM MODEL 136466WB5V-FANTENNA100 -2500 GHz1ST LO5 RECEIVERSMITEQ MULTIPLEXER 1-53–21GHzAMP1450 MHzMITEQ 136460 DOWNCONVERTER2ND LO5-19.5 GHzCW3-21 GHz1300 MHz BWTO DOWNCONVERTERVOLTAGE TOFREQ.CONVERTERV-FCHANNELIF OUT250 -1550 MHzIF OUTCAL PORTCAL SOURCERF INAMP1MUX3AMP2LSB=0.5dB4LSB=0.5dBB9B8ATNATN4WB7WB8WB6V-FV-FV-FB9OUTB8OUTB7AMP3AMP4B7OUTOUTLINE DRAWING0.200[5.08]6.600 [167.64]5.165 [131.19]5.040 [128.02]4.915 [124.84]0.250 [6.35] 2.520 [64.01]0.725 [18.42]0.250 [6.35]0.250[6.35]J621 20 19 18 17 16 15 14 13 1211 10 9 8 7 6 5 4 3 2 15.125[130.18]J521 20 19 18 17 16 15 14 13 1211 10 9 8 7 6 5 4 3 2 13.568[90.63]0.737[18.72]2.813[71.45]1.975[50.17]J1J2J3J41.184[30.07]1.768[44.91]2.318[58.88]0.555[14.10]0.125[3.18]0.125 [3.18]0.125 [3.18]DIA. THRU.TYP. (9) PLACES4.350 [110.49]6.475 [164.47]2.350 [59.69]0.555[14.10]0.600 [15.24]"SMA" FEMALE CONNECTORTYP. (4) PLACESGENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]35

MODEL 136466 TYPICAL DATARF GAIN (dB)26242220181614121086420-2-4-6-8-10-12-141300 MHz RF CHANNELS (AT 25°C)12.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5FREQUENCY (GHz)INPUT VSWR32.82.62.42.221.81.61.41.2VSWR IN/OUTNORMALIZED GAIN (dB)0-3-6-9-12-15-18-21-24-27-30450 MHz DETECTED VOLTAGE TO FREQUENCY OUTPUTS (AT 25°C).1009080706050403020100DETECTED VOLTAGE TOFREQUENCY OUTPUT (kHz)2.56 2.66 2.76 2.86 2.96 3.06 3.16 3.26 3.36 3.46 3.566.76 6.86 6.96 7.06 7.16 7.26 7.36 7.46 7.56 7.66 7.76RF INPUT FREQUENCY (GHz)RF INPUT FREQUENCY (GHz)NORMALIZED GAIN (dB)0-3-6-9-12-15-18-21-24-27-301009080706050403020100DETECTED VOLTAGE TOFREQUENCY OUTPUT (kHz)NORMALIZED GAIN (dB)0-3-6-9-12-15-18-21-24-27-3004.26 4.36 4.46 4.56 4.66 4.76 4.86 4.96 5.06 5.16 5.26RF INPUT FREQUENCY (GHz)100908070605040302010DETECTED VOLTAGE TOFREQUENCY OUTPUT (kHz)NORMALIZED GAIN (dB)10090807060504030201000-3-6-9-12-15-18-21-24-27-307.36 7.46 7.56 7.66 7.76 7.86 7.96 8.06 8.16 8.26 8.36RF INPUT FREQUENCY (GHz)DETECTED VOLTAGE TOFREQUENCY OUTPUT (kHz)36

FEATURES7.9–14.9 GHz FREQUENCY MULTIPLEXERMODEL: 136468• High reliability, spaceborne application• RF coverage.............................. 7.9–14.9 GHz• Gain ........................................... 23 dB nominal• Channel-to-channel isolation.. 45 dB minimum• Input/output VSWR................... 1.5:1 maximum• Noise figure .............................. 3.5 dB typical,4.5 dB maximum• Low power ................................ 130 mA (5 V) typical• Lightweight ............................... 320 grams typicalMITEQ’s model 136468 five-output frequency multiplexer precedes the second IF down conversion stage in a lowearth orbit-based millimeter-wave radiometer. In combination with second IF downconverter, the system providesmaximally flat frequency response over the bands of interest, high linearity of output power to input power, and highisolation between the frequency bands of interest as well as from other undesirable signals. In addition, this highreliability, spaceborne integrated assembly is optimized for small size, low power consumption, lightweight, andexcellent thermal stability of operation.ELECTRICAL SPECIFICATIONSRF INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.Frequency range GHz 7.9 14.9VSWR Ratio 1.5:1RF OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.Number of RF output channels 5Channel 2 dB bandwidth MHz 1300Channel 20 dB rejection band MHz 2300Channel center frequencies GHz 8.5858, 9.0798,10.3013,12.4566, 14.2367Nominal gain dB 23Output power (1 dB compression) dBm -5 -3Noise figure dB 3.5 4.5Isolation between output channels dB 45VSWR Over 1300 MHz passband Ratio 1.5:1Connectors, RFSMAOTHER PARAMETERS CONDITION UNITS MIN. TYP. MAX.Connector, DC9-pin, micro DSupply voltage Volts 5DC power consumption At 5 V supply mA 130Weight Grams 320ENVIRONMENTAL CONDITIONSOperating temperature . . . . . . . . . . 10 to 60°CStorage temperature . . . . . . . . . . . -25 to +60°CVibration . . . . . . . . . . . . . . . . . . . . 6.5 Gs RMS, 20–2000 HzRadiation . . . . . . . . . . . . . . . . . . . . 30 krads, total DOSP37

MODEL 136468 TYPICAL DATARF GAIN (dB)26242220181614121086420-2-4-6-8-10-12-14MULTIPLEXER CHANNELIZED OUTPUTS (AT 25°C)17 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 13.5 14 14.5 15 15.5 16FREQUENCY (GHz)32.82.62.42.221.81.61.41.2INPUT VSWRFUNCTIONAL BLOCK DIAGRAMSGENERIC SYSTEM MODEL 136468ANTENNA100 –2500 GHz1ST LO5 RECEIVERSMITEQ MULTIPLEXER 1–53–21GHzAMP1450 MHzMITEQ 136460 DOWNCONVERTER2ND LO5–19.5 GHzCW3–21 GHz1300 MHz BWTO DOWNCONVERTERVOLTAGE TOFREQ.CONVERTERV–FCHANNELIF OUT250 –1550 MHzIF OUTCAL PORTCAL SOURCERF INAMP1MUX2AMP2AMP3B3B6B5B2B4B3OUTB6OUTB5OUTB2OUTB4OUTOUTLINE DRAWING0.430 [10.92]0.200 [5.08]0.625 [15.88]5.745 [145.92]6.175 [156.85]6.050 [153.67]0.430 [10.92]0.638 [16.21]3.538[89.87]1.523[38.68]3.288[83.52]0.125[3.18]J1J7J6J3J4J2J52.938[74.63]1.188[30.18]1.838[46.69]2.388[60.66]0.320[8.13]0.125 [3.18]0.718 [18.24]3.087 [78.41]GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]0.250 [6.35] 0.250 [6.35]0.125 [3.18] DIA. THRU.TYP. (6) PLACES0.600 [15.24]38

FEATURES7.6–21.2 GHz FREQUENCY MULTIPLEXERMODEL: 136462• High reliability, spaceborne application• Broadband RF coverage.......... 7.6–21.2 GHz• Gain ........................................... 23 dB nominal• Channel-to-channel isolation.. 50 dB minimum• Input/output VSWR................... 1.5:1 typ., 1.8:1 maximum• Noise figure .............................. 4 dB typ., 6 dB maximum• Low power ................................ 130 mA (5 V) typical• Lightweight ............................... 210 grams typicalMITEQ’s model 136462 broadband three-output frequency multiplexer precedes the second IF down conversionstage in a low earth orbit-based millimeter-wave radiometer. In combination with second IF downconverter, thesystem provides maximally flat frequency response over the bands of interest, high linearity of output power to inputpower, and high isolation between the frequency bands of interest as well as from other undesirable signals. Inaddition, this high reliability, spaceborne integrated assembly is optimized for small size, low power consumption,lightweight, and excellent thermal stability of operation.ELECTRICAL SPECIFICATIONSRF INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.Frequency range GHz 7.6 21.2VSWR Ratio 1.8:1RF OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX.Number of RF output channels 3Channel bandwidth MHz 1300Channel center frequencies GHz 8.408112.775920.4012Gain flatness Over 1300 MHz passband dB 2Normal gain dB 23Channel 20 dB rejection bandwidth MHz 2300Output power (1 dB compression) dBm -8 -5Noise figure dB 4 6Isolation between output channels dB 50VSWR Over 1300 MHz passband Ratio 1.5:1 1.8:1OTHER PARAMETERS CONDITION UNITS MIN. TYP. MAX.Connectors, RFSMAConnector, DC15-pin, micro DSupply voltage Volts 5DC power consumption At 5 V supply mA 130Weight Grams 210ENVIRONMENTAL CONDITIONSOperating temperature . . . . . . . . . . 10 to 60°CStorage temperature . . . . . . . . . . . -25 to +60°CVibration . . . . . . . . . . . . . . . . . . . . 6.5 Gs RMS, 20–2000 HzRadiation . . . . . . . . . . . . . . . . . . . . 30 krads, total DOSP39

MODEL 136462 TYPICAL DATARF GAIN (dB)MULTIPLEXER CHANNELIZED OUTPUTS (AT 25°C)26242220181614121086420INPUT VSWR-2-4-6-8-10-12-146.8 7.8 8.8 9.8 10.8 11.8 12.8 13.8 14.8 15.8 16.8 17.8 18.8 19.8 20.8 21.8FREQUENCY (GHz)32.82.62.42.221.81.61.41.21VSWR (IN/OUT)FUNCTIONAL BLOCK DIAGRAMSGENERIC SYSTEM MODEL 136462ANTENNA100 –2500 GHz1ST LO5 RECEIVERSMITEQ MULTIPLEXER 1–53–21GHzAMP1450 MHzMITEQ 136460 DOWNCONVERTERIF OUT250–1550 MHzIF OUTCAL PORT2ND LO5–19.5 GHzCW3–21 GHzCAL SOURCE1300 MHz BWTO DOWNCONV.VOLTAGE TOFREQ. CONVERTERV–FCHANNELRF INAMP1MUX5B17B16B15B17OUTB16OUTB15OUTOUTLINE DRAWING5.870 [149.10]0.430 [10.92]0.200 [5.08]0.250 [6.35]2.935 [74.55]0.250 [6.35]5.745 [145.93]0.430 [10.92]2.400 [60.96]1.638[41.61]2.275[57.79]0.125[3.18]J1J5J4J3J21.800[45.72]1.250[15.24]0.600[15.24]0.320 [8.13]0.125 [3.18]0.125 [3.18] DIA. THRU.TYP. (6) PLACES4.644 [117.96]"SMA" FEMALECONNECTORTYP. (4) PLACES0.600 [15.24]8 7 6 5 4 3 2 115 14 13 12 11 10 9MDM-152GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]40

TRANSMIT SWITCHED MULTIPLEXERMODEL: 127086FEATURE• Three-channel design• Insertion loss.........................3 dB maximum• Flatness .................................0.5 dB maximum• Isolation .................................60 dB minimumMITEQ’S model 127086 integrated, switched filter assembly features three channelized, printed circuit filter banks,individually selectable by a TTL driven, single-pole, three-throw PIN switch. This arrangement offers very lowinsertion loss, high isolation and excellent flatness over each passband. MITEQ’s Microwave Assemblies, Systemsand Technologies Group specializes in the manufacture of integrated switched frequency multiplexers and is ableto offer a wide range of frequency ranges and a number of channels.SPECIFICATIONSPARAMETERSFrequency rangeBand 1Band 2Band 3IsolationInsertion lossFlatnessVSWRSupply voltageControlBPF Band 1FrequencyRejectionInsertion lossFlatnessVSWRBPF Band 2FrequencyRejectionInsertion lossFlatnessVSWRBPF Band 3FrequencyRejectionInsertion lossFlatnessVSWRLIMITS6.68–7.18 GHz6.39–6.64 GHz4.625–5.205 GHz60 dB minimum3 dB maximum0.5 dB/RF band1.5:1 maximum5.2 V0.C.= Off, GND = On6.68–7.18 GHz> 20 dB at 8.35–8.975 GHz1 dB nominal0.7 dB nominal1.5:1 nominal6.39–6.64 GHz> 20 dB at 4.79–4.98 GHz1 dB nominal0.7 dB nominal1.5:1 nominal4.625–5.205 GHz> 20 dB at 5.78–6.51 GHz2 dB nominal0.7 dB nominal1.5:1 nominal41

MODEL 127086 TYPICAL DATAFUNCTIONAL BLOCK DIAGRAMBAND 1: 6.68–7.18 GHzJ1BAND 2: 6.39–6.64 GHzJ0J2BAND 3: 4.625–5.205 GHzJ3OUTLINE DRAWING0.40 [10.16]0.35 [8.89]3.050 [77.47]0.7[18.03]0.53 [13.46]0.53 [13.46]0.41[10.41]0.41[10.41]E1E2J0RTNE3J1J2J30.50[12.7]1.530[38.86]0.50[12.7]1.75[44.45]0.13 [3.30]0.102 [2.59] DIA. THRUC'BORE. 0.188 [4.78] DIA.X 0.13 [3.30] DP. TYP.(4) HOLES3.75 [95.25]0.11 [2.79]TYPE "SMA"FEMALE CONNECTORTYP. (4) PLACES0.13 [3.30] TYP.GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]42

TRANSMIT/RECEIVE SWITCH/AMPLIFIERMODEL: 127077FEATURES• Serves as an amplified duplexer• Low noise figure• Tx-Rx isolation greater than 40 dB• Handles up to 2 watts of transmit power+BEANTP/N 127077S/NRCV TXSPECIFICATIONSPARAMETERS LIMITS CONDITIONSFrequency receive band2.2–4.2 GHzFrequency transmit bands1.75–1.85 GHz and 5.9–6.4 GHzReceive gain 27 dB maximum, 21 dB minimum Includes gain vs. temperaturevariations and gain slopeNoise figure1.7 dB maximumReceive P1 dB output4 dB minimumReceive isolation20 dB minimumTransmit to antenna loss0.7 dB maximumTransmit to receive isolation40 dB minimumTransmit input power33 dBmVSWR all RF ports 2:1 Z0 = 50 ΩStabilityUnconditionalSwitch control15 mA = Receive mode-15 mA = Transmit modeControl and DC connectionsSolderable wiresRF connectionsBondable ribbonsDC power consumption8 V @ 120 mA maximumENVIRONMENTAL CONDITIONSWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 gramsOperating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 70°CStorage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30 to +85°CFUNCTIONAL BLOCK DIAGRAMOUTLINE DRAWINGCONTROL:ANTENNATRANSMITANTENNAPORTTRANSMITPORT0.004 [.10] DIA.WIRETYP. (2) PLACES0.44[11.18] 0.26[6.60]E+80.63 [16.0]0.27 [6.86]ANTRCVTX0.16 [4.06] MAX.0.03 [.76]GROUNDPLATE0.56[14.22]8 V0.27[6.86]0.09 [2.29]0.15 [3.81] TO 0.022 [0.559] WIDERIBBON, TYP. (3) PLACES0.08 [2.03]RECEIVEPORTGENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows:.xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]43

FEATURESAMPLIFIER/SWITCH ASSEMBLYMODEL: 126140• Military application• Broadband RF coverage .... 0.475–18.5 GHz• RF gain................................. 23 dB nominal• Channel-to-channelisolation ............................... 45 dB minimum• Input/output VSWR.............. 1.5:1 typical, 1.8:1 maximum• Noise figure ......................... 3.5 dB typical, 4.5 dB maximum• Low power ........................... 325 mA (5 V) typical• Lightweight .......................... 520 grams typicalFrequency Noise 1 dB CW PulseRange Gain Gain Figure Flatness Comp. IP 3 IP 2 RF RFBand (GHz) (dB, Min.) (dB, Max.) (dB, Max.) (±dB) (dB, Min.) (+dB, Min.) (+dB, Min.) (+dBm, Max.) (+dBm, Max.)1 0.475–1.050 18 22 2 1 11 21 30 32 572 0.950–2.100 18 22 2.2 1 11 21 30 32 573 1.950–3.800 20 24 2 1.25 8 18 27 32 574 3.100–6.100 22 26 2.6 1.25 8 18 27 31 565 5.400–10.400 24 30 2.7 1.5 7 16.5 25 31 566 9.600–18.500 28 32 4.8 2.25 6 15 23 30 557 2.000–18.500 20 26 4.5 2 9 19 22 10 N/A8 2.000–18.5000 25 32 4.5 2 9 19 22 10 N/AELECTRICAL SPECIFICATIONSPARAMETERS LIMITS CONDITIONSVSWR2.1:1 maximumStability Unconditional Source impedance is BPF with passband VSWR < 2:1On/Off isolation30 dB minimumSwitching speed200 µs maximumVideo feedthru -75 dBm maximum from 1 kHz to 4 GHz PRF = 1 kHzControlTTLControl logic “1” = Channel On, “0” = Channel Off No input = “0”BlankingAll “0” = BlankingDC bias12 V @ 650 mA maximum,-12 V @ 250 mA maximumENVIRONMENTAL CONDITIONSWeight . . . . . . . . . . . . . . . . . . . . . . . . 200 gramsOperating/storage temperature . . . . . . . -54 to +71°CVibration . . . . . . . . . . . . . . . . . . . . . . . . Sinusoidal 5 Gs RMS,52–500 Hz2.40[60.96]2.250[57.15]0.075[1.91].075[1.91]OUTLINE DRAWINGJ3J7J6J43.25 [82.55]1.625 [41.28]3.100 [78.74]J03 7 8 4 -12V +12V 2 6 5 1J1J5J8J20.100[2.54] DIA. THRU.'C' BORE. 0.25 [6.35] DIA. X0.20 [5.08] DEEP (4) HOLES0.450 [11.43]0.500 [12.7] TYP.NOTES:1. PAINT PER MIL-C-83286 GREY,COLOR NO. 26492 PER FED-STD-595.2. MARKING TO BE IN BLACK INK.0.265 [6.73] TYP."SMA" FEMALECONNECTORTYP. (9) PLACESGENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]0.60 [15.24]0.37 [9.40] TYP.0.375 [9.53] TYP.0.450[11.43]TYP.1.425[36.20]0.400[10.16]0.200 [5.08]TYP. (6) PLACES0.03 [0.76] DIA. TINNEDPIN TYP.0.14 [3.56] TYP.44

MINIATURE CALIBRATION SWITCHMODEL: 125475FEATURES• Compact package• Tight amplitude and phase tracking• Fast switching• Blind mate connectors• Airborne military applicationsSPECIFICATIONSPARAMETERS LIMITS CONDITIONS COMMENTSFrequency range6–18 GHzInsertion loss 3.3 dB maximum AZ/EL→Sig., Ref. In→Ref. Out10 dB maximum Cal. In→Sig., Cal. In→Ref. OutAmplitude balance ±0.5 dB maximum AZ/EL→Sig.Phase balance ±5° maximum AZ/EL→Sig.Isolation 25 dB minimum Sig.1 Out to Sig. 2 Out Cal. select60 dB minimum any unselected path AZ/EL selectVSWR 2:1 maximum Selected portsSwitching speed 50 ns maximum 50% TTL to 10 to 90% RFDC power 5 V @ 100 mA maximum, Typical-15 V @ 100 mA maximumControlTTL, 3 linesSwitch positions Transmission paths Path AZ EL CALSelect Select Select1. AZ1→Sig. 1, AZ2→Sig. 2, Ref. In→Ref. Out 1. 0 1 12. EL1→Sig. 1, EL2→Sig. 2, Ref. In→Ref. Out 2. 1 0 13. Cal.→Sig. 1, Cal.→Sig. 2, Cal.→Ref. Out 3. 1 1 0RF connectorsGilbert GPO maleFUNCTIONAL BLOCK DIAGRAMOUTLINE DRAWINGAZ 1EL 1 SIGNAL 10.40[10.16]SOLDER PINS1.76 [44.70]0.346 [8.79]REF. INTYPE "GPO" MALE CONNECTOR,FULL DETENT, TYP. (9) PLACES1.470 [37.34]0.131 [3.33]"J9" (REF. OUT)0.145 [3.68]REF. OUTEL 2AZ 2SIGNAL 2CALIBRATIONIN0.487 [12.37]0.487 [12.37]J1+5VE1E2J2E3-15VJ3GND0.104 [2.64] DIA.THRU TYP. (4) HOLES0.50[12.7]J9 J4J5J6J7J80.63 [16.0]0.243 [6.17]1.450.243 [6.17] [36.83]0.243 [6.17]1.300[33.02]0.243 [6.17]0.075 [1.91]±0.010GENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]45

SWITCHABLE FILTER BANKMODEL: 127938FEATURES• Single input and output• Insertion loss......................... 5 dB maximum• Amplitude balance ................ 0.5 dB maximum• VSWR ..................................... 1.5:1 maximumE1E2J1 P/N 127938J2S/NRTNMITEQ’s model 127938 integrated, two part, switchable filter bank features two channelized, printed circuit filterbanks, individually selectable by TTL driven, SP2T PIN switches the input and output. MITEQ’s MicrowaveAssemblies, Systems and Technologies Group specializes in the manufacture of integrated switch filter assembliesand is able to offer a wide range of frequency ranges and a number of channels.SPECIFICATIONSPARAMETERS BAND 1 BAND 2Passband frequency 10.7–11.8 GHz 11.7–12.75 GHzInsertion loss 5 dB maximum 5 dB maximumInsertion loss flatness 0.7 dB maximum, 0.2 dB any 36 MHz band 0.7 dB maximum, 0.2 dB any 36 MHz bandDifference in band level 0.5 dB maximum 0.5 dB maximumVSWR 1.5:1 maximum 1.5:1 maximumGroup delay (any 40 MHz band)Linear 0.01 ns/MHz maximum 0.01 ns/MHz maximumRipple 0.5 ns p-p maximum 0.5 ns p-p maximumRejection 14.88–15.98 GHz > 80 dB 15.88–16.91 GHz > 80 dB12.79–13.89 GHz > 50 dB 13.79–14.84 GHz > 50 dBSwitch positions Select E1 = 0 V Select E2 = 0 VReturn voltage 5 V 5 VENVIRONMENTAL CONDITIONSWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 gramsOperating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 70°CStorage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30 to +85°CFUNCTIONAL BLOCK DIAGRAMBLOCK DIAGRAM0.38 [9.65]OUTLINE DRAWING2.67 [67.82]0.90 [22.86]BAND 1: 10.7–11.8 GHz0.85[21.59]E1E2J1RTNJ21.85[46.99]1.63[41.40]J1J20.13 [3.30] (4) HOLES X 0.13 [3.30] DEEP TYP.C'BORE 0.188 [4.775] DIA. 0.102 [2.591] DIA. THRUBAND 2 : 11.7–12.75 GHz0.11[2.79]4.47 [113.54]TYP. "SMA"MALE CONNECTORTYP. (2) PLACESGENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]46

FEATURES14.5 GHz OSCILLATORMODEL: 127090• Output power......................... 13–20 dBm• Harmonic levels .................... -20 dBc maximum• Spurious levels ..................... -60 dBc maximum• Phase noise (1 Hz BW)......... -105 dBc/Hz,100 kHz from the carrier• Power consumption.............. 4.5 WRF OUT+15 VSPECIFICATIONSPARAMETERSLIMITSCenter frequency14.5 GHzOutput power13–20 dBmPower vs. temperature±1.5 dB maximumOperating case temperature-54 to +85°CFrequency accuracy0.10% maximumTemperature stability±0.05% maximumPulling (RL = 12 dB)±0.02% maximumPushing±0.001% maximumHarmonics-20 dBc maximumSpurious-60 dBc maximumSSB phase noise 1Hz BW typical10 kHz from the carrier -80 dBc/Hz maximum100 kHz from the carrier -105 dBc/Hz maximumDC voltage15 ±0.5 VDC current300 mASurvival voltage20 V maximumSurvival operating temperature100°C maximumStorage temperature-50 to +125°C maximumWeight1.75 oz. maximumConsult factory for additional frequencies that are available.FUNCTIONAL BLOCK DIAGRAMOUTLINE DRAWINGX2VOLTAGEREG.RFOUT+15 V0.38 [9.65]"SMA"FEMALECONNECTOR0.80 [20.32]RF OUT2.75 [69.85]2.57 [65.28]+15 V1.38[35.05]1.60[40.64]1.38 [35.05]SOLDER PIN4 MOUNTING HOLES0.120 [3.05] DIA. THRUGENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]0.21 [5.33]0.81[20.57]0.32[8.13]47

FEATURES• Used as microwave leveling loop• Ultra-miniaturized selfcontainedAGC feedback loop• External threshold adjust forsetting desired output power• Output power settability of ±0.2 dB• -45 to +85°C operation over airborneenvironmentsX-BAND LEVELERMODEL: 124511J1J2GND-15V +15VPARAMETERSFrequency rangeInsertion lossInsertion loss flatnessVSWRInput powerOutput level adjustOutput level flatnessOutput level vs. temperatureResponse timeSecond harmonicSpuriousDC powerWeightOperating temperatureStorage temperatureSPECIFICATIONSLIMITS8.3–10.3 GHz2.5 dB maximum0.4 dB maximum1.5:1 maximum23 dBm maximum-4.5 to +16 dBm±0.2 dB maximum0.5 dB maximumRise/fall time 100 ns, delay 200 ns maximum30 dBc maximum @ P in = 20 dBm-60 dBc15 V @ 50 mA maximum,-15 V @ 10 mA maximum50 grams-45 to +85°C-55 to +85°CFUNCTIONAL BLOCK DIAGRAMOUTLINE DRAWINGRFINPUTPINATTENUATORRFOUTPUTOUTPUT1.220[31.0]0.512 [13.0]1.47[36.0]TYPE "SMA" FEMALECONNECTOR, TYP. (2) PLACES2.047 [52.0].118 [3.0] 1.811[46.0]0.375 [9.5] TYP.J2GND-15V +15VTHRESHOLDADJUSTLEVELINGLOOPJ13.008[76.4]2.758[70.1]2.548[64.7]0.944[24.0]0.40 [10.16]INPUTLEVEL SET1.000[25.4]0.126 [3.2]M3 X 0.236 [6.0] DP. MIN.TYP. (4) HOLESGENERAL NOTES:1. Dimensions shown in brackets [ ] are in millimeters.2. Tolerance as follows: .xx = ±0.01 [.xx = ±0.25], .xxx = ±0.005 [.xxx = ±0.13]48

PIN SWITCHESTEL: (631) 439-9137FAX: (631) 436-9219E-MAIL: jpierro@miteq.comDATECOMPANYADDRESSCONTACTTEL.FAXE-MAILFor additional technical, price and delivery information, please copy, complete and mail or fax this form to (631) 436-9219, or call John Pierro at (631) 439-9137.SPECIFICATION PARAMETER REQUIREMENT 1 REQUIREMENT 2 REQUIREMENT 3Frequency range (GHz)Type (i.e., SP6T)Insertion loss (dB, maximum)Isolation (dB, minimum)VSWR (maximum)Type (reflective/absorptive)DC power (±V)Current consumption (±V, mA)Video leakage (dBm)Switching speed (ns)ConnectorsOperating temperatureQuantitySpecial requirements, such as special testing/screening, or specific operating environment may belisted below:PLEASE SEND ADDITIONAL INFORMATION ON THE FOLLOWING MITEQ PRODUCTS:AmplifiersMixersMultipliersFrequency SourcesPassive Power ComponentsIF Signal Processing ComponentsIntegrated AssembliesSATCOM Products49100 Davids Drive, Hauppauge, NY 11788TEL.: (631) 436-7400 • FAX: (631) 436-9219/436-7430www.miteq.com

3 dB HYBRIDSTEL: (631) 439-9137FAX: (631) 436-9219E-MAIL: jpierro@miteq.comDATECOMPANYADDRESSCONTACTTEL.FAXE-MAILFor additional technical, price and delivery information, please copy, complete and mail or fax this form to (631) 436-9219, or call John Pierro at (631) 439-9137.SPECIFICATION PARAMETER REQUIREMENT 1 REQUIREMENT 2 REQUIREMENT 3Frequency range (GHz)Nominal split (dB)Insertion loss (dB, maximum)Isolation (dB, minimum)Amplitude balance (±dB, maximum)Phase balance (±deg., maximum)VSWR (maximum)ConnectorsOperating temperatureQuantitySpecial requirements, such as special testing/screening, or specific operating environment may belisted below:PLEASE SEND ADDITIONAL INFORMATION ON THE FOLLOWING MITEQ PRODUCTS:AmplifiersMixersMultipliersFrequency SourcesPassive Power ComponentsIF Signal Processing ComponentsIntegrated AssembliesSATCOM Products100 Davids Drive, Hauppauge, NY 11788TEL.: (631) 436-7400 • FAX: (631) 436-9219/436-7430www.miteq.com50

TEL: (631) 439-9137FAX: (631) 436-9219E-MAIL: jpierro@miteq.comBROADBANDPOWER DIVIDERSDATECOMPANYADDRESSCONTACTTEL.FAXE-MAILFor additional technical, price and delivery information, please copy, complete and mail or fax this form to (631) 436-9219, or call John Pierro at (631) 439-9137.SPECIFICATION PARAMETER REQUIREMENT 1 REQUIREMENT 2 REQUIREMENT 3Frequency range (GHz)Divide byInsertion loss (dB, maximum)Isolation (dB, minimum)Amplitude balance (±dB, maximum)Phase balance (±deg., maximum)Input/output VSWR (maximum)ConnectorsOperating temperatureQuantitySpecial requirements, such as special testing/screening, or specific operating environment maybe listed below:PLEASE SEND ADDITIONAL INFORMATION ON THE FOLLOWING MITEQ PRODUCTS:AmplifiersMixersMultipliersFrequency SourcesPassive Power ComponentsIF Signal Processing ComponentsIntegrated AssembliesSATCOM Products51100 Davids Drive, Hauppauge, NY 11788TEL.: (631) 436-7400 • FAX: (631) 436-9219/436-7430www.miteq.com

TEL: (631) 439-9137FAX: (631) 436-9219E-MAIL: jpierro@miteq.comANALOGPIN ATTENUATORSDATECOMPANYADDRESSCONTACTTEL.FAXE-MAILFor additional technical, price and delivery information, please copy, complete and mail or fax this form to (631) 436-9219, or call John Pierro at (631) 439-9137.SPECIFICATION PARAMETER REQUIREMENT 1 REQUIREMENT 2 REQUIREMENT 3Frequency range (GHz)Insertion loss (dB, maximum)Input/output VSWR (maximum)Amplitude response (dB, MHz)Attenuation range (dB, minimum)Control options (VDC)ConnectorsOperating temperatureQuantitySpecial requirements, such as special testing/screening, or specific operating environment may belisted below:PLEASE SEND ADDITIONAL INFORMATION ON THE FOLLOWING MITEQ PRODUCTS:AmplifiersMixersMultipliersFrequency SourcesPassive Power ComponentsIF Signal Processing ComponentsIntegrated AssembliesSATCOM Products100 Davids Drive, Hauppauge, NY 11788TEL.: (631) 436-7400 • FAX: (631) 436-9219/436-7430www.miteq.com 52

PHASE SHIFTERSTEL: (631) 439-9137FAX: (631) 436-9219E-MAIL: jpierro@miteq.comDATECOMPANYADDRESSCONTACTTEL.FAXE-MAILFor additional technical, price and delivery information, please copy, complete and mail or fax this form to (631) 436-9219, or call John Pierro at (631) 439-9137.SPECIFICATION PARAMETER REQUIREMENT 1 REQUIREMENT 2 REQUIREMENT 3RF frequency range (GHz)Insertion loss (dB, maximum)Input/output VSWR (maximum)Phase shift (deg., maximum)Phase shift step size (deg.)Phase error (deg.)Third-order intercept (dBm, minimum)Switching speed (ns)Control options (VDC)Type of controlOperating temperatureQuantitySpecial requirements, such as output power variations over temperature and frequency, specialtesting/screening, or specific operating environment may be listed below:PLEASE SEND ADDITIONAL INFORMATION ON THE FOLLOWING MITEQ PRODUCTS:AmplifiersMixersMultipliersFrequency SourcesPassive Power ComponentsIF Signal Processing ComponentsIntegrated AssembliesSATCOM Products53100 Davids Drive, Hauppauge, NY 11788TEL.: (631) 436-7400 • FAX: (631) 436-9219/436-7430www.miteq.com

MODULATORSTEL: (631) 439-9137FAX: (631) 436-9219E-MAIL: jpierro@miteq.comDATECOMPANYADDRESSCONTACTTEL.FAXE-MAILFor additional technical, price and delivery information, please copy, complete and mail or fax this form to (631) 436-9219, or call John Pierro at (631) 439-9137.SPECIFICATION PARAMETER REQUIREMENT 1 REQUIREMENT 2 REQUIREMENT 3RF/LO frequency range (GHz)IF frequency range (MHz)Conversion loss (dB, maximum)Isolation, RF and LO (dB, minimum)IF amplitude balance (±dBm, maximum)IF phase balance (±deg., maximum)RF VSWR (maximum)LO/IF VSWR (maximum)RF input (P1 dB compression point) (dBm, minimum)LO drive level (dBm, minimum)Operating temperatureQuantitySpecial requirements, such as special testing/screening, or specific operating environment may belisted below:PLEASE SEND ADDITIONAL INFORMATION ON THE FOLLOWING MITEQ PRODUCTS:AmplifiersMixersMultipliersFrequency SourcesPassive Power ComponentsIF Signal Processing ComponentsIntegrated AssembliesSATCOM Products100 Davids Drive, Hauppauge, NY 11788TEL.: (631) 436-7400 • FAX: (631) 436-9219/436-7430www.miteq.com 54

COUPLERSTEL: (631) 439-9137FAX: (631) 436-9219E-MAIL: jpierro@miteq.comDATECOMPANYADDRESSCONTACTTEL.FAXE-MAILFor additional technical, price and delivery information, please copy, complete and mail or fax this form to (631) 436-9219, or call John Pierro at (631) 439-9137.SPECIFICATION PARAMETER REQUIREMENT 1 REQUIREMENT 2 REQUIREMENT 3Frequency range (GHz)Coupling (dB)Insertion loss (dB, maximum)Input/output VSWR (maximum)Operating temperatureQuantitySpecial requirements, such as special testing/screening, or specific operating environment may belisted below:PLEASE SEND ADDITIONAL INFORMATION ON THE FOLLOWING MITEQ PRODUCTS:AmplifiersMixersMultipliersFrequency SourcesPassive Power ComponentsIF Signal Processing ComponentsIntegrated AssembliesSATCOM Products55100 Davids Drive, Hauppauge, NY 11788TEL.: (631) 436-7400 • FAX: (631) 436-9219/436-7430www.miteq.com

LIMITERSTEL: (631) 439-9137FAX: (631) 436-9219E-MAIL: jpierro@miteq.comDATECOMPANYADDRESSCONTACTTEL.FAXE-MAILFor additional technical, price and delivery information, please copy, complete and mail or fax this form to (631) 436-9219, or call John Pierro at (631) 439-9137.SPECIFICATION PARAMETER REQUIREMENT 1 REQUIREMENT 2 REQUIREMENT 3Frequency range (GHz)Insertion loss (dB, maximum)Input/output VSWR (maximum)RF power, pulsed (dBm, minimum)RF power, CW (dBm, maximum)Flat leakage (dBm, maximum)Spike leakage (erg, maximum)IP 3 (dBm, minimum)LinearityRecovery time (ns)Operating temperatureQuantitySpecial requirements, such as special testing/screening, or specific operating environment may belisted below:PLEASE SEND ADDITIONAL INFORMATION ON THE FOLLOWING MITEQ PRODUCTS:AmplifiersMixersMultipliersFrequency SourcesPassive Power ComponentsIF Signal Processing ComponentsIntegrated AssembliesSATCOM Products100 Davids Drive, Hauppauge, NY 11788TEL.: (631) 436-7400 • FAX: (631) 436-9219/436-7430www.miteq.com 56

ORDERING INFORMATIONPRICING AND TERMSA quotation on any item in the catalog is available bycontacting the factory. All quotations, unlessotherwise noted, are valid for 60 days from the date ofissue, F.O.B. (FCA) Hauppauge, NY 11788. Pricingdoes not include customer or government sourceinspection unless otherwise noted. On internationalorders, an irrevocable letter of credit may be required.MITEQ accepts these credit cards:®CardsWelcome®MasterCard®QUANTITY DISCOUNTSA quantity discount is generally available on mostcatalog items. Due to the wide variety of devices inthe catalog, it is not possible to provide a standarddiscount schedule. When quantities are involved,please contact the factory and the appropriateinformation will be provided.SHIPPING INFORMATIONUnless instructed otherwise by the customer, we willship UPS in the U.S. F.O.B. (FCA) Hauppauge. Airfreight will be used as the primary international meansof shipment. Please indicate at time of purchase whatmethod of shipment you require.DRAWINGS AND SPECIFICATIONSMaterial presented in this catalog is current at thetime of printing. Mechanical and electricalrequirements are subject to change. If either of theseparameters is critical, please contact the factory toverify that the information is current.APPLICATION ENGINEERINGWe maintain a large support staff of engineers whoare experts in specific areas of microwavetechnology. Each has an engineering backgroundthat combines both a formal engineering educationwith training and experience in product design. Asfurther technical support, we make available theservices of our engineering and scientific staff, whomay be consulted on more advanced circuit designsor application problems.RETURNED MATERIALWhen returning material for repair or replacement,please ensure that there is complete informationincluded with the shipment, giving a detaileddescription of the reason for its return, the date andpurchase order on which it was obtained, and theexact address to which the material is to bereshipped. All returns must arrive freight, postage,duties and handling prepaid.SOURCE INSPECTIONGovernment/customer source inspection is availableon any item upon receipt of the complete writtenconfirmation of purchase order items, including theprime government contract number. Source inspectionwith respect to some products increases the unit priceand extends delivery because of duplicate standardfinal inspection and testing. It is recommended whereverpossible that a Certificate of Compliance besubstituted for source inspection to minimize priceand delivery delays.REPAIR COSTSWarranty repairs will be made at no cost to thecustomer. Units out of warranty, or those which havebeen mishandled, will require approval by thecustomer for the charges involved before the repairscan be accomplished. We will provide an estimate forthe cost of the repair, which can be applied to therepair, if approval is granted. For those items that aredeemed beyond repair, or where the customer maydecide not to repair the unit, a handling charge will becharged.FEDERAL SUPPLY CODEOur Federal Supply Code is: 3359257

WARRANTY1. MITEQ, Inc. warrants to the purchaser that each of its products, when shipped will be free from defects in materialand workmanship and will perform in full accordance with applicable specifications. The limit of liability under thiswarranty is at MITEQ, Inc.’s option, to repair or replace any product or part thereof which shall within: (a) threeyears of delivery for indoor equipment, (b) two years of delivery for outdoor equipment and (c) one year of deliveryfor integrated assemblies or equipment having RF output powers equal to or greater than +24 dBm, be returnedby the purchaser to MITEQ, Inc., at 100 Davids Drive, Hauppauge, New York, 11788, and shall, as determined byexamination by MITEQ, Inc., prove defective in material and/or workmanship. Warranty returns must first beauthorized in writing by MITEQ, Inc. Disassembly of any MITEQ, Inc. product by anyone other than an authorizedrepresentative of MITEQ, Inc. voids this warranty in its entirety. MITEQ, Inc. reserves the right to make changesin any of its products without incurring any obligation to make the same changes on previously delivered products.2. Components and subsystems having been repaired by MITEQ, Inc. shall be warranted for that repair for ninety(90) days. For products that are still within the original warranty period as described above, the original warranty(if longer) will take precedence. For all SATCOM products, that portion of the system that is repaired, will be warrantiedfor one year.3. As a condition to the warranties provided for herein, the Buyer will prepay the shipping charges for all productsreturned to MITEQ, Inc. for repair and MITEQ, Inc. will pay the return shipping with the exception of rack mountablehardware returned from outside the United States in which case the Buyer will pay the shipping charges.4. The Buyer will pay the cost of inspecting and testing any goods returned under the warranty or otherwise whichare found to meet the applicable specifications or which are not defective or not covered by the warranty.5. Products sold by MITEQ, Inc. shall not be considered defective or non-conforming to the Buyers’ order if they (a)satisfactorily fulfill the performance requirements that were (i) provided by the Buyer to MITEQ, Inc. or (ii) as publishedin the Sellers’ product specification literature, or (b) or in accordance with any written or verbal agreementbetween the Buyer and MITEQ, Inc., or (c) are in accordance with samples approved by the Buyer. This warrantyshall not apply to any products or parts thereof which have been subject to accident, negligence, alteration, abuseor misuse. MITEQ, Inc. makes no warranty whatsoever in respect to accessories or parts not supplied by it.6. Limitations of Warranty, Damages and LiabilityEXCEPT AS EXPRESSLY SET FORTH HEREIN, THERE ARE NO WARRANTIES, CONDITIONS, GUARANTEESOR REPRESENTATIONS AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR OTHERWARRANTIES, CONDITIONS, GUARANTEES OR REPRESENTATIONS, WHETHER EXPRESSED OR IMPLIED,IN LAW OR IN FACT, ORAL OR IN WRITING.MITEQ, INC.’S AGGREGATE LIABILITY IN DAMAGES OR OTHERWISE SHALL NOT EXCEED THE PAYMENT, IFANY, RECEIVED BY MITEQ, INC. FOR THE UNIT OF PRODUCT OR SERVICE FURNISHED OR TO BEFURNISHED, AS THE CASE MAY BE, WHICH IS THE SUBJECT OF CLAIM OR DISPUTE. IN NO EVENT SHALLMITEQ, INC. BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES, HOWSOEVERCAUSED.7. All matters regarding this warranty shall be interpreted in accordance with the laws of the State of New York andany controversy that cannot be settled directly shall be settled by arbitration in New York, New York in accordancewith the rules then prevailing of the American Arbitration Association, and judgement upon the award renderedmay be entered in any court having jurisdiction thereof.58

Davids Drive • Hauppauge, NYOser Avenue • Hauppauge, NY100 Davids Drive, Hauppauge, NY 11788TEL.: (631) 436-7400 • FAX: (631) 436-7430www.miteq.comC-35