Front Drop Axle Kit - Total Cost Involved
Front Drop Axle Kit - Total Cost Involved Front Drop Axle Kit - Total Cost Involved
28-34 Front 4-link Drop AxleInstallation Instruction1-866-925-1101www.totalcostinvolved.comCHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLATING OF THE KIT.IF ANY PIECES ARE MISSING, PLEASE CONTACT: TOTAL COST INVOLVED 800-925-1101We recommend that you box your frame from the front crossmember to the firewall. If this can'tbe done, box a section that extends at least 4 inches on either side of the 4-link frame bracket.Once the frame is boxed, tack weld or clamp driver side frame bracket (bracket with steeringplate if Mustang type steering is being used) to bottom edge of frame, flush with side of frame atposition indicated by the print at right which applies to your car. Repeat procedure for passengerside bracket. To locate hole for top bar on '32-'34's, use measurement shown on print at right.Bore or hole saw a 7/8" hole in frame and weld in frame bushing. Bolt bars to brackets and uppermounting hole in frame with adjustable ends toward front, with front end partially assembled.Check front end for square before final welding. After welding, finish grind weld on side offrame for clean appearance.D.C Series KitD.C. series axle brackets utilizeslip-in tapered buttons to acceptspring perch. These buttons aresimply slipped into place as shownwhen installing the bracket ontothe axle. The top button has amilled relief on one side to clearthe weld on the bracket. Be sure toposition this button correctly toinsure that it seats flat wheninstalled.(c) 2008 Total Cost Involved Engineering, Inc. All Rights Reserved1
28-34 <strong>Front</strong> 4-link <strong>Drop</strong> <strong>Axle</strong>Installation Instruction1-866-925-1101www.totalcostinvolved.comCHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLATING OF THE KIT.IF ANY PIECES ARE MISSING, PLEASE CONTACT: TOTAL COST INVOLVED 800-925-1101We recommend that you box your frame from the front crossmember to the firewall. If this can'tbe done, box a section that extends at least 4 inches on either side of the 4-link frame bracket.Once the frame is boxed, tack weld or clamp driver side frame bracket (bracket with steeringplate if Mustang type steering is being used) to bottom edge of frame, flush with side of frame atposition indicated by the print at right which applies to your car. Repeat procedure for passengerside bracket. To locate hole for top bar on '32-'34's, use measurement shown on print at right.Bore or hole saw a 7/8" hole in frame and weld in frame bushing. Bolt bars to brackets and uppermounting hole in frame with adjustable ends toward front, with front end partially assembled.Check front end for square before final welding. After welding, finish grind weld on side offrame for clean appearance.D.C Series <strong>Kit</strong>D.C. series axle brackets utilizeslip-in tapered buttons to acceptspring perch. These buttons aresimply slipped into place as shownwhen installing the bracket ontothe axle. The top button has amilled relief on one side to clearthe weld on the bracket. Be sure toposition this button correctly toinsure that it seats flat wheninstalled.(c) 2008 <strong>Total</strong> <strong>Cost</strong> <strong>Involved</strong> Engineering, Inc. All Rights Reserved1
28-31 FORDMeasure 27 inchesback from center ofradiator mountinghole along top offrame rail to a pointon frame 90 degreesfrom bottom hole in4-link bracket.32 FORDTo locate framebracket, measure 233/8" back from centerof radiator mountinghole along top offrame rail to a pointon frame 90 degreesfrom bottom hole in4-link bracket. Centerof hole for top bar islocated 4 7/8" aboveand 1/4" behindcenter of bottom hole.33-34 FORDTo locate framebracket, measure 241/2" back from lowerfender brace hole onframe (straight) tomounting hole inframe bracket. Upper hole is located 4 7/8" above lower hole and 24" back from lower fenderbrace hole on frame.(c) 2008 <strong>Total</strong> <strong>Cost</strong> <strong>Involved</strong> Engineering, Inc. All Rights Reserved2
Change language