Owner's manual - Electric bikes & folding bikes
Owner's manual - Electric bikes & folding bikes Owner's manual - Electric bikes & folding bikes
owner's manual4.0 UnpackingNOTE: Your A2B weighs 37.2 kg (82 lb).LIFT WITH CARE. Two people are recommended.4.1 Tools and equipment• Pliers• Side cutters (for cutting cable ties used to pack the A2B)• Blanket or tarpaulin (to avoid scratching unprotectedsurfaces on the A2B whilst unpacking)4.2 Delivered fully assembled and batterychargedYour A2B should be fully assembled and the batterycharged by your Ultra Motor dealer at the time of delivery.If not contact us immediately as this will void your warranty.However, if you need to unpack your A2B, follow theseinstructions:1. Carefully open the flaps at the top of the carton.Remove all staples (with pliers if necessary), to avoid thepossibility of scratching yourself or your A2B.2. Carefully lift the A2B out of the carton. Two people arerecommended.3. Lay the A2B on a tarpaulin or blanket to avoid scratchingany unprotected surface whilst you remove the packingmaterials.4. Remove the accessory boxes from the carton.5. Using the side cutters, clip the cable ties that hold variouscomponents to the frame. ONLY clip those cable ties thatare used to attach components to the frame or preventmovement during shipment (and NOT those trimmed ofexcess length).The A2B has cable ties that manage electrical andcontrol cable routing (and ARE trimmed of excess length).DO NOT clip these cable ties as they are necessary for thesafe operation of the vehicle.6. Remove all of the protective wrapping from the A2B anddispose of the packaging responsibly.The battery and charger should be tested when received.If the battery or charger is damaged in any way, a claimshould be filed with the carrier. A full report of the damageshould be obtained by the claim agent, and this reportshould be forwarded to Ultra Motor. Ultra Motor will advisethe action required and arrange for repair or replacement.Charge the battery for at least 12 hours before usingthe A2B for the first time. See 6.2 & 6.3.7
acbd4.3 Installing the handlebar and display1. Using a 4 mm allen key, unscrew the three bolts that holdthe handlebar clamp to the handlebar stem (pic a).2. Remove the cap from the handlebar stem (pic b).3. Nest the handlebar into the handlebar stem, ensuringthat it is centred and properly oriented. Replace the cap,reinstall the bolts holding the cap to the stem and tightensecurely the bolts to 6 Nm per bolt (pic c).It is essential to tighten all three bolts evenly to ensureproper installation.4. Install the display and tighten the bolts to 6 Nm per bolt.Caution: this is an A-head stem, the top scew D ispreloaded with 1-2 Nm and does not adjust the handlebarstem. Trying to tighten bolt D can damage the head setbearings.The left side bolt on the bar stem must be tightened to10-12 Nm.The 'Nm' measurements refer to the torque value thatshould be applied to the tightening of bolts, please use anappropriate spanner to apply the correct torque values asspecified.8
- Page 1 and 2: BA228114
- Page 4 and 5: owner's manualContents1.0 Introduct
- Page 6 and 7: owner's manual2.0 Important informa
- Page 8 and 9: owner's manual1.2.3.4.5.6.7.8.9.10.
- Page 12: owner's manual4.4 Installing the pe
- Page 17 and 18: Remember that there are power cut-o
- Page 19 and 20: 5.6 Luggage CarrierYour A2B equippe
- Page 21 and 22: 6.0 Battery use, storage and dispos
- Page 23 and 24: • The Indicator LED will illumina
- Page 25 and 26: Charging instructions for storageBe
- Page 27 and 28: Check your A2B before every ride.Do
- Page 29 and 30: 8.0 MaintenanceHave your A2B checke
- Page 31 and 32: 8.7 Removing and re-installing whee
- Page 33 and 34: Removing rear wheel1. Ensure that t
- Page 35 and 36: 9.0 CleaningRubber and plastic part
- Page 37 and 38: 3411.0 Technical InformationGeneral
- Page 39 and 40: 2.3.6 any modification, alteration
- Page 41: Ultra MotorUltra Motor USA 1661 Ten
owner's <strong>manual</strong>4.0 UnpackingNOTE: Your A2B weighs 37.2 kg (82 lb).LIFT WITH CARE. Two people are recommended.4.1 Tools and equipment• Pliers• Side cutters (for cutting cable ties used to pack the A2B)• Blanket or tarpaulin (to avoid scratching unprotectedsurfaces on the A2B whilst unpacking)4.2 Delivered fully assembled and batterychargedYour A2B should be fully assembled and the batterycharged by your Ultra Motor dealer at the time of delivery.If not contact us immediately as this will void your warranty.However, if you need to unpack your A2B, follow theseinstructions:1. Carefully open the flaps at the top of the carton.Remove all staples (with pliers if necessary), to avoid thepossibility of scratching yourself or your A2B.2. Carefully lift the A2B out of the carton. Two people arerecommended.3. Lay the A2B on a tarpaulin or blanket to avoid scratchingany unprotected surface whilst you remove the packingmaterials.4. Remove the accessory boxes from the carton.5. Using the side cutters, clip the cable ties that hold variouscomponents to the frame. ONLY clip those cable ties thatare used to attach components to the frame or preventmovement during shipment (and NOT those trimmed ofexcess length).The A2B has cable ties that manage electrical andcontrol cable routing (and ARE trimmed of excess length).DO NOT clip these cable ties as they are necessary for thesafe operation of the vehicle.6. Remove all of the protective wrapping from the A2B anddispose of the packaging responsibly.The battery and charger should be tested when received.If the battery or charger is damaged in any way, a claimshould be filed with the carrier. A full report of the damageshould be obtained by the claim agent, and this reportshould be forwarded to Ultra Motor. Ultra Motor will advisethe action required and arrange for repair or replacement.Charge the battery for at least 12 hours before usingthe A2B for the first time. See 6.2 & 6.3.7
Change language