Arc Protection Relay REA 10_ - APE Distribuidor ABB

More documents

Recommendations

Info

Arc Protection Relay REA 10_1MRS750929-MBGOptolink communicationThe REA 101 relay contains two communicationlinks: Optolink 1 and Optolink 2.The selection switches are used to select thelinks to be used, and the messages to be communicatedbetween them.The purpose of thecommunication link is to communicateON/OFF type messages between the centralunits over the signal transfer fiber. The messagecan be:• Light signal• Overcurrent signal• Trip signalOnly one type of message per optolink can betransmitted between the central units. Thedata to be communicated depends on the systemdesign.To monitor the connection, a test pulse is sentthrough the signal transfer fiber at regularintervals. If the test pulse is not received atthe specified time, the optolink fault LED(“Optolink 1 Fault” or “Optolink 2 Fault”)and the “IRF” LED of the central unit is lit,and the IRF relay resets.Circuit-breaker failure protectionThe circuit-breaker failure protection (CBFP)is enabled, when the Trip Condition keyswitch is in “Current&Light” position.The circuit-breaker failure protection isimplemented by delaying either the HSO2output or the TRIP3 output, or when required,both the outputs. Note that if both the outputsare used, the delay time is the same, but thepick-up time of the relay (5...15 ms) is addedto the TRIP3 relay.The selection switches are used to select thewanted alternative.The selected delay time, 100 ms or 150 ms,starts running once the HSO1 is activated.Delayed tripping does not take place if theovercurrent signal disappears before the specifiedtime delay elapses.When the circuit-breaker failure protection isnot in use, all the trip outputs operate in parallel.Self-supervision unitIn addition to that mentioned in the abovesections, the self-supervision unit (IRF) monitorsthe operating voltage of the relay. If afault is detected in the operating voltages, theself-supervision unit prevents the relay fromoperating. In addition, the “IRF” LED of thecentral unit is lit, and the IRF relay resets.The self-supervision signal output operateson the closed circuit principle as presented inthe figure below. Under normal conditions,the output relay is energized and the contactgap between 8 and 10 is closed. If the auxiliarypower supply fails, or an internal fault isdetected, the contact gap between 8 and 10 isopened.IRFFig. 3Self-supervision output (IRF)10A050349Extension unit REA 103The Arc Protection Module REA 103 is anextension unit designed to be used togetherwith the central unit REA 101.The function of the REA 103 unit is to detectlight and to provide the REA 101 relay withinformation about this.The use of the extension unit allows the protectionarea to be extended and the protectedobject to be divided into smaller areasFeatures:Normal condition8910• Two sensor fibers for arc detection; loop orradial arrangement• Two signal relays for each sensor fiber• Relays activated by light detected by thesensor fiber• Two RJ-45 ports for connecting REA 101relay and extension units• Self-supervision unit monitoring operatingvoltages and sensor fiber loops.Extension unit REA 105The Arc Protection Module REA 105 is anextension unit designed to be used togetherwith the central unit REA 101.IRFFault conditionThe function of the REA 105 unit is to detectlight and to carry out tripping, if the REA 101relay provides an overcurrent signal at thesame time, or delivers a trip command.The use of extension units allows the protectionarea to be extended and the protectedobject to be divided into smaller areas. Thus amore selective system is obtained.896
Arc Protection Relay REA 10_1MRS750929-MBGFeatures:• Loop-type or radial sensor fiber for arcdetection.• Two high-speed semi-conductor outputsfor tripping.• Signal relay activated by light detected bythe sensor fiber.• Three RJ-45 ports for connecting theREA 101 relay and extension units.• Circuit-breaker failure protection. Delayedlight signal to REA 101, which opens thehigher-level circuit breaker.• Self-supervision unit which monitors operatingvoltages and the sensor fiber loop.Extension unit REA 107The Arc Protection Module REA 107 is anextension unit designed to be used togetherwith the central unit, Arc Protection RelayREA 101.The function of the REA 107 unit is to detectlight and to provide the REA 101 relay withinformation about this.The use of the extension unit allows the protectionarea to be extended and the protectedobject to be divided into smaller areas.Features:• 8 lens-type sensors for arc detection• 2 signal relays• 2 RJ-45 ports for connecting REA 101relay and other extension units• Self-supervision unit that monitors operatingvoltages• LED indicators for each sensor.7
Page 1: Arc Protection RelayREA 10_Product
Page 4 and 5: Arc Protection Relay REA 10_1MRS750
Page 12 and 13: 135,2±1Arc Protection Relay REA 10
Page 20: ABB OyDistribution AutomationP.O. B

Arc Protection Relay REA 10_ - APE Distribuidor ABB

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?