horizontal/vertical metal cutting bandsaw - Harbor Freight Tools
horizontal/vertical metal cutting bandsaw - Harbor Freight Tools horizontal/vertical metal cutting bandsaw - Harbor Freight Tools
3.Improper connection of the equipment-groundingconductor can resultin a risk of electric shock. Theconductor with insulation having anouter surface that is green with orwithout yellow stripes is the equipment-groundingconductor. If repairor replacement of the electric cord orplug is necessary, do not connect theequipment-grounding conductor to alive terminal.8.9.The outlet must be properly installedand grounded in accordance with allcodes and ordinances.Do not use an adapter to connect thistool to a different outlet.Double Insulated Tools: Toolswith Two Prong Plugs4.Check with a qualified electrician orservice personnel if the groundinginstructions are not completely understood,or if in doubt as to whether thetool is properly grounded.5.6.Use only 3-wire extension cords thathave 3-prong grounding plugs and3-pole receptacles that accept thetool’s plug.Repair or replace damaged or worncord immediately.1.To reduce the risk of electric shock,double insulated equipment has a polarizedplug (one blade is wider thanthe other). This plug will fit in a polarizedoutlet only one way. If the plugdoes not fit fully in the outlet, reversethe plug. If it still does not fit, contacta qualified electrician to install theproper outlet. Do not change the plugin any way.2.Double insulated tools may be usedin either of the 120 volt outlets shownin the preceding illustration. (SeeOutlets for 2-Prong Plug.)7. This tool is intended for use on a circuitthat has an outlet that looks likethe one illustrated above in 125 V~3-Prong Plug and Outlet. The toolhas a grounding plug that looks likethe plug illustrated above in 125 V~3-Prong Plug and Outlet.SKU 93762 For technical questions, please call 1-800-444-3353. Page 8
SPECIFICATIONSMotor120 V~ / 60 Hz / 1 HP / n 01700/minCutting Capacity 4-1/2” Round Stock /4” x 6” Rectangular StockSpeeds80 FPM / 120 FPM / 200 FPMThroat Depth 4-1/2”Angle CuttingCapacity0° ~ 55° (Left) Miter Plate onHorizontal Cutting BedBlade 64” L x 15/32” W x 0.025” Thick /14 TPIHorizontal Bed 11-1/2” L x 7-1/2” W x 23-1/2” HeightVertical Bed 9-5/8” L x 9-1/2” W x 33-1/2” HeightV-Belt Type 0-506UNPACKINGWhen unpacking, check to make sureall the parts shown on the Parts Lists onpages 31 and 32 are included. If anyparts are missing or broken, please callHarbor Freight Tools at the number shownon the cover of this manual as soon aspossible.ASSEMBLY INSTRUCTIONSNote: For additional information regardingthe parts listed in the following pages,refer to the Assembly Diagram onpage 33.CAUTION! Always make sure the PowerSwitch (164) for the Bandsaw is inits “OFF” position and the tool isunplugged from its electrical outletprior to assembling the tool, addingany accessories, or making adjustmentsto the tool.To Assemble The Stand:PIN(172)PULLHANDLE(173)STAND(174)TOOL PLATE(175)SCREW(178)FLAT WASHER(177)NUT(176)STAND(174)FIGURE AFLAT WASHER(180)NUT(181)WHEEL (182)FLATWASHER(184)HEX BOLT (183)SPRING WASHER (185)WHEELBRACKET(186)WHEEL SHAFT(187)PIN(188)1. Insert the Pull Handle (173) into thetwo mounting holes located in the uppersection of one Stand (174). Thensecure the Pull Handle to the Stand,using two Pins (172).(See Figure A.)2.3.Attach one end of the Tool Plate(175) to the upper section of oneStand (174), using two Screws (178),two Flat Washers (177), and two Nuts(176). (See Figure A.)Attach the other end of the ToolPlate (175) to the upper section ofthe remaining Stand (174), usingtwo Screws (178), two Flat Washers(177), and two Nuts (176).(See Figure A.)To Attach The Wheels To The Stand:Align the two mounting holes in theWheel Bracket (186) with the twomounting holes located in the lowersection of the Stand (174). Then securethe Wheel Bracket to the Stand,using two Hex Bolts (183), two SpringWashers (185), two Flat Washers(184), two Flat Washers (180), andtwo Nuts (181). (See Figure A.)SKU 93762 For technical questions, please call 1-800-444-3353. Page 9
- Page 1 and 2: horizontal/verticalmetal cutting ba
- Page 3 and 4: Save This ManualKeep this manual fo
- Page 5 and 6: 20.21.1.2.3.4.5.6.7.8.or other part
- Page 7: ditions and situations that may occ
- Page 11 and 12: To Attach The Pulley Cover:WORMSHAF
- Page 13 and 14: SMALL VERTICAL CUTTING PLATE (194)V
- Page 15: AdjustmentsTo Adjust The Stock Stop
- Page 18 and 19: Basic Bandsaw Operation --Vertical
- Page 20 and 21: Blade into the workpiece. (See Figu
- Page 22 and 23: e. Place the new Saw Blade (82) bet
- Page 24 and 25: TROUBLESHOOTINGSKU 93762 For techni
- Page 26 and 27: Part # Description Qty80 Motor Pull
- Page 28 and 29: ASSEMBLY DIAGRAM194: Vertical Cutti
SPECIFICATIONSMotor120 V~ / 60 Hz / 1 HP / n 01700/minCutting Capacity 4-1/2” Round Stock /4” x 6” Rectangular StockSpeeds80 FPM / 120 FPM / 200 FPMThroat Depth 4-1/2”Angle CuttingCapacity0° ~ 55° (Left) Miter Plate onHorizontal Cutting BedBlade 64” L x 15/32” W x 0.025” Thick /14 TPIHorizontal Bed 11-1/2” L x 7-1/2” W x 23-1/2” HeightVertical Bed 9-5/8” L x 9-1/2” W x 33-1/2” HeightV-Belt Type 0-506UNPACKINGWhen unpacking, check to make sureall the parts shown on the Parts Lists onpages 31 and 32 are included. If anyparts are missing or broken, please call<strong>Harbor</strong> <strong>Freight</strong> <strong>Tools</strong> at the number shownon the cover of this manual as soon aspossible.ASSEMBLY INSTRUCTIONSNote: For additional information regardingthe parts listed in the following pages,refer to the Assembly Diagram onpage 33.CAUTION! Always make sure the PowerSwitch (164) for the Bandsaw is inits “OFF” position and the tool isunplugged from its electrical outletprior to assembling the tool, addingany accessories, or making adjustmentsto the tool.To Assemble The Stand:PIN(172)PULLHANDLE(173)STAND(174)TOOL PLATE(175)SCREW(178)FLAT WASHER(177)NUT(176)STAND(174)FIGURE AFLAT WASHER(180)NUT(181)WHEEL (182)FLATWASHER(184)HEX BOLT (183)SPRING WASHER (185)WHEELBRACKET(186)WHEEL SHAFT(187)PIN(188)1. Insert the Pull Handle (173) into thetwo mounting holes located in the uppersection of one Stand (174). Thensecure the Pull Handle to the Stand,using two Pins (172).(See Figure A.)2.3.Attach one end of the Tool Plate(175) to the upper section of oneStand (174), using two Screws (178),two Flat Washers (177), and two Nuts(176). (See Figure A.)Attach the other end of the ToolPlate (175) to the upper section ofthe remaining Stand (174), usingtwo Screws (178), two Flat Washers(177), and two Nuts (176).(See Figure A.)To Attach The Wheels To The Stand:Align the two mounting holes in theWheel Bracket (186) with the twomounting holes located in the lowersection of the Stand (174). Then securethe Wheel Bracket to the Stand,using two Hex Bolts (183), two SpringWashers (185), two Flat Washers(184), two Flat Washers (180), andtwo Nuts (181). (See Figure A.)SKU 93762 For technical questions, please call 1-800-444-3353. Page 9