horizontal/vertical metal cutting bandsaw - Harbor Freight Tools

More documents

Recommendations

Info

7.8.DON’T FORCE TOOL. It will do thejob better and safer at the rate forwhich it was designed.USE RIGHT TOOL. Don’t force toolor attachment to do a job for which itwas not designed.RECOMMENDED MINIMUM WIREGAUGE FOR EXTENSION CORDS(120 VOLT)NAMEPLATEAMPERES(at full load)9.10.11.EXTENSION CORDLENGTH25’ 50’ 100’ 150’0 – 6 18 16 16 146.1 – 10 18 16 14 1210.1 – 12 16 16 14 1212.1 – 16 14 12 Do not use.TABLE AUSE PROPER EXTENSION CORD.Make sure your extension cord isin good condition. When using anextension cord, be sure to use oneheavy enough to carry the currentyour product will draw. An undersizedcord will cause a drop in line voltageresulting in loss of power and overheating.Table A shows the correctsize to use depending on cord lengthand nameplate ampere rating. If indoubt, use the next heavier gage.The smaller the gage number, theheavier the cord.WEAR PROPER APPAREL. Do notwear loose clothing, gloves, neckties,rings, bracelets, or other jewelrywhich may get caught in movingparts. Nonslip footwear is recommended.Wear protective hair coveringto contain long hair.12.13.14.15.16.17.18.19.ALWAYS USE SAFETY GLASSES.Also use face or dust mask if cuttingoperation is dusty. Everyday eyeglassesonly have impact resistantlenses, they are NOT safety glasses.SECURE WORK. Use clamps or avise to hold work when practical. It’ssafer than using your hand and itfrees both hands to operate tool.DON’T OVERREACH. Keep properfooting and balance at all times.MAINTAIN TOOLS WITH CARE.Keep tools sharp and clean for bestand safest performance. Followinstructions for lubricating and changingaccessories.DISCONNECT TOOLS before servicing;when changing accessories,such as blades, bits, cutters, and thelike.REDUCE THE RISK OF UNINTEN-TIONAL STARTING. Make sureswitch is in off position before pluggingin.USE RECOMMENDED ACCESSO-RIES. Consult the owner’s manual forrecommended accessories. The useof improper accessories may causerisk of injury to persons.NEVER STAND ON TOOL. Seriousinjury could occur if the tool is tippedor if the cutting tool is unintentionallycontacted.CHECK DAMAGED PARTS. Beforefurther use of the tool, a guard orother part that is damaged shouldbe carefully checked to determinethat it will operate properly and performits intended function – check foralignment of moving parts, bindingof moving parts, breakage of parts,mounting, and any other conditionsthat may affect its operation. A guardSKU 93762 For technical questions, please call 1-800-444-3353. Page 4
20.21.1.2.3.4.5.6.7.8.or other part that is damaged shouldbe properly repaired or replaced.DIRECTION OF FEED. Feed workinto a blade or cutter against thedirection of rotation of the blade orcutter only.NEVER LEAVE TOOL RUNNINGUNATTENDED. TURN POWER OFF.Don’t leave tool until it comes to acomplete stop.Band Saw Safety WarningsFor Your Own Safety Read InstructionManual Before Operating SawWear eye protection.Do not remove jammed cutoff piecesuntil blade has stopped.Maintain proper adjustment of bladetension, blade guides, and thrustbearings.Adjust upper guide to just clear workpiece.Hold workpiece firmly against table.Keep hands away from cutting areaand Saw Blade.Properly adjust the upper bladeguide, blade tension and thrust bearingbefore each use to reduce the riskof injury. See Operating Instructionsfor explanation of needed adjustments.Never leave the Bandsaw unattendedwhen it is plugged into an electricaloutlet. Turn off the tool, and unplugit from its electrical outlet before leaving.9.10.11.12.13.14.15.16.17.18.Make sure the Bandsaw is located ona flat, level, sturdy surface capableof supporting the weight of the Sawand workpieces. Always “chock” theWheels to prevent the Bandsaw fromaccidentally moving.Before using the Bandsaw, check tomake sure the Saw Blade is properlymounted and is not cracked or bent.Never attempt to cut more than oneworkpiece at a time.Never attempt to cut freehand. Makesure the workpiece to be cut ispressed firmly against the Table and/or secured in the Vise.When cutting a large workpiece,make sure its entire length is properlysupported. If necessary, use a rollerstand (not included).Do not lean on the Bandsaw whenthe tool is in its upright position.When moving the Bandsaw, alwayshave its Head lowered to its horizontalposition and the Locking Pin (115)inserted in the Pivot (120).Allow the Saw Blade to rotate to fullspeed before feeding a workpieceinto the Blade. When turning off theBandsaw, allow the Saw Blade tospin down and stop on its own. Donot press against the Saw Blade tostop it.Wear heavy-duty work gloves whenchanging the Saw Blade.Turn off the Bandsaw and allow theSaw Blade to completely stop if theSaw Blade is to be backed out of anuncompleted cut.SKU 93762 For technical questions, please call 1-800-444-3353. Page 5
Page 1 and 2: horizontal/verticalmetal cutting ba
Page 3: Save This ManualKeep this manual fo
Page 7 and 8: ditions and situations that may occ
Page 9 and 10: SPECIFICATIONSMotor120 V~ / 60 Hz /
Page 11 and 12: To Attach The Pulley Cover:WORMSHAF
Page 13 and 14: SMALL VERTICAL CUTTING PLATE (194)V
Page 15: AdjustmentsTo Adjust The Stock Stop
Page 18 and 19: Basic Bandsaw Operation --Vertical
Page 20 and 21: Blade into the workpiece. (See Figu
Page 22 and 23: e. Place the new Saw Blade (82) bet
Page 24 and 25: TROUBLESHOOTINGSKU 93762 For techni
Page 26 and 27: Part # Description Qty80 Motor Pull
Page 28 and 29: ASSEMBLY DIAGRAM194: Vertical Cutti

horizontal/vertical metal cutting bandsaw - Harbor Freight Tools

Create successful ePaper yourself

Delete template?

Save as template?